Instruction/ maintenance manual of the product CC3700H-2X Pelco
Go to page of 16
® Installa tion/Oper a tion CC3700 Series Color Camera C1986M-B (11/03) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.
[ 2 ] Pelco Manual C1986M-B (1 1/03).
Pelco Manual C1986M-B (11/03) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS .............................................................................................. ....... 4 Regulatory Notices ..............................................
[ 4 ] Pelco Manual C1986M-B (1 1/03) IMPORT ANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
Pelco Manual C1986M-B (11/03) [ 5 ] DESCRIPTION The CC3700 Series is a compact, color video camera with a 1/3-inch CCD imager . All cameras have a direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses. Models CC3700S-2 Standard resolution, 330 TV lines, SuperHAD™ CCD, 0.
[ 6 ] Pelco Manual C1986M-B (1 1/03) CAMERA LA Y OUT NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations. The trim ring also hides the power connectors and protects the DIP switches.
Pelco Manual C1986M-B (11/03) [ 7 ] PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS 1 Control coil negative (-) Lens positive supply 2 Control coil positive (+) Not used 3D rive coil positive (+) Video drive signal 4D rive coil negative (-) Ground Figure 2.
[ 8 ] Pelco Manual C1986M-B (1 1/03) POWER AND VIDEO CONNECTIONS The CC3700 Series camera is designed to operate from a 12 VDC or 24 V AC power supply . The power supply connections are shown in Figure 4. The LED on the back panel of the camera indicates that power is connected.
Pelco Manual C1986M-B (11/03) [ 9 ] AC Operation Only – If you are wiring more than one camera to the same transformer , connect one side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras.
[ 10 ] Pelco Manual C1986M-B (1 1/03) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak).
Pelco Manual C1986M-B (11/03) [ 11 ] BA CK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 12 ] Pelco Manual C1986M-B (1 1/03) SWIT CH SETTINGS Figure 7. Switch Settings (Defaults) Gamma (NOR/LIN Switch) - Switch Setting 8 Sets the Gamma level to one of the following: NOR (Default setting) - Increases visibility in dark areas of the picture.
Pelco Manual C1986M-B (11/03) [ 13 ] Shutter Speed Selection - Switch Settings 4, 3, 2, and 1 ESC (Electronic Sensitivity Contr ol) Switch Settings 4, 3, and 1 The ESC feature compensates for an excessive light level by automatically adjust- ing shutter speed.
[ 14 ] Pelco Manual C1986M-B (1 1/03) CAMERA SYNCHRONIZA TION When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line-locking, the cameras to one another .
Pelco Manual C1986M-B (11/03) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Picture Elements CC3700S-2: 510 (H) x 492 (V) CC3700H-2: 768 (H) x 494 (V) Sensing Area: 6mm diagonal Synchronization .
® Pelco, the Pelco logo, Spectra, Genex, Legacy , Esprit, and Camclosure are registered trademarks of Pelco. ™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation. © Copyright 2002, Pelco. All rights reserved. WARRANTY AND RETURN INFORMA TION REVISION HISTOR Y Manual # Date Comments C1986M 3/02 Original version.
An important point after buying a device Pelco CC3700H-2X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco CC3700H-2X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco CC3700H-2X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco CC3700H-2X you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco CC3700H-2X will certainly help you make a decision on the purchase.
If you already are a holder of Pelco CC3700H-2X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco CC3700H-2X.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco CC3700H-2X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco CC3700H-2X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
