Instruction/ maintenance manual of the product CC3600 Pelco
Go to page of 16
® Installa tion/Oper a tion CC3500/CC3600 Series Color Cameras C1981M-C (8/02) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.
[ 2 ] Pelco Manual C1981M-C (8/02).
Pelco Manual C1981M-C (8/02) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS ................................................................................. 4 Regulatory Notices ....................................................................
[ 4 ] Pelco Manual C1981M-C (8/02) IMPORT ANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
Pelco Manual C1981M-C (8/02) [ 5 ] DESCRIPTION The CC3500 and CC3600 Series are compact, color video cameras with a 1/3-inch CCD imager . All cameras have a direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses.
[ 6 ] Pelco Manual C1981M-C (8/02) CAMERA LA Y OUT INST ALLA TION Lens Mounting The CC3500 and CC3600 Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Cameras are factory-set for CS-mount lenses, but easily adjusted for C-mount lenses.
Pelco Manual C1981M-C (8/02) [ 7 ] PIN DD LENS CONNECTIONS AI LENS CONNECTIONS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3 Drive coil positive (+) Video drive signal 4 Drive coil negative (-) Ground Figure 2.
[ 8 ] Pelco Manual C1981M-C (8/02) POWER AND VIDEO CONNECTIONS To connect the camera power and video do the following: 1. Remove the rear cover from the camera (refer to Figure 1). Thread cabling through the rear cover . 2. Connect the power cable to the two pin power connector on the back of the camera using the terminal block connector provided.
Pelco Manual C1981M-C (8/02) [ 9 ] AC Operation Only – If you are wiring more than one camera to the same transformer , connect one side of the transformer to the same terminal on all cameras, and connect the other side of the trans- former to the remaining terminal on all cameras.
[ 10 ] Pelco Manual C1981M-C (8/02) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AI. Switch the EI and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak).
Pelco Manual C1981M-C (8/02) [ 11 ] BA CK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 12 ] Pelco Manual C1981M-C (8/02) SWIT CH SETTINGS Figure 7. Switch Settings 01236 10 9 8 7 6 5 4 3 2 1 BLACK REPRESENTS SWITCH POSITION 10 9 AUTO 10 9 6300 O K 10 9 3200 O K 10 9 4200 O K 8 8 NORMAL (0.
Pelco Manual C1981M-C (8/02) [ 13 ] Shutter Speed Selection - Switch Settings 4, 3, 2, and 1 4 3 2 1 1/50 4 3 2 1 1/125 1/250 1/500 1/1,000 1/2,000 1/4,000 1/10,000 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 4 3.
[ 14 ] Pelco Manual C1981M-C (8/02) CAMERA SYNCHRONIZA TION When using one AC power supply in a multi camera system, a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll adjust the phase control to synchronize (line-lock), the cameras to one another .
Pelco Manual C1981M-C (8/02) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Picture Elements CC3500S-2: 510 (H) x 492 (V) CC3500H-2: 768 (H) x 494 (V) CC3600H-2: 768 (H) x 494 (V) Sensing Area: 6.
® Pelco, the Pelco logo, Spectra, Genex, Legacy , PelcoVision, Esprit, and Camclosure are registered trademarks of Pelco. ™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation. © Copyright 2002, Pelco. All rights reserved. WARRANTY AND RETURN INFORMA TION REVISION HISTOR Y Manual # Date Comments C1981M 6/00 Original version.
An important point after buying a device Pelco CC3600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco CC3600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco CC3600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco CC3600 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco CC3600 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco CC3600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco CC3600.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco CC3600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco CC3600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
