Instruction/ maintenance manual of the product C538M Pelco
Go to page of 17
® Pelco World Headquarters • 3500 Pelco Way, Clovis, California 93612-5699 USA • www.pelco.com USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150 International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120 ADDENDUM Addendum No.
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108 Inte.
2 Pelco Manual C544M (2/98) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS ............................... 3 2.0 DESCRIPTION .
Pelco Manual C544M (2/98) 3 Please thor oughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed.
4 Pelco Manual C544M (2/98) 2.0 DESCRIPTION The Pelco 9760-IRC VCR Controller provides remote control of most VCRs equipped with an infrared receiver for controlling standard functions: play , record, stop, fast-forward, rewind, and pause. Eject control depends on the VCR model.
Pelco Manual C544M (2/98) 5 2.1 GENERAL FEA TURES The Pelco 9760-IRC is housed in a rack frame and connects to one Sercom port on the rear of the CM9760-CC1. • A fully populated Pelco 9760-IRC unit consists of the following: a. One communication card (interfaces with CM9760-CC1) b.
6 Pelco Manual C544M (2/98) 2.2 SAMPLE SYSTEM A typical system installation involving the CM9760-IRC might include: a. CM9760-CC1 e. Monitors b. CM9760-IRC f. Cameras c. CM9760-KBD g. CM9760-MXBs d. VCRs Other Pelco products can be added according to system requirements.
Pelco Manual C544M (2/98) 7 3.0 INST ALLA TION T o install the Pelco Infrared VCR Controller , proceed as follows: 1. Set the baud. 2. Set the start address. 3. Connect the CM9760-IRC to the CM9760-CC1 host. 4. Connect additional IRC units in daisy-chain fashion.
8 Pelco Manual C544M (2/98) 3.1.1 Setting the Baud Bauds of 2400, 4800, 9600, and 19200 are available. The communication protocol uses eight data bits, one stop bit, and even parity . The baud is set using DIP switches 1 and 2 according to T able A. NOTE: The operating baud must match the baud rate set in the .
Pelco Manual C544M (2/98) 9 3.2.1 Setting the Start Address Each Pelco CM9760-IRC unit requires a six-bit start address. The start address is configured using the DIP switches on the communication card (see Figure 5: DIP switches). Each control card occupies one address space.
10 Pelco Manual C544M (2/98) 3.3 CONNECTING THE CM9760-IRC TO THE CM9760-CC1 HOST Each CM9760-IRC has two RS-422 ports; one labeled IN (male) and the other OUT (female). T o connect a CM9760-IRC to the CM9760-CC1 host, connect a SerCom port on the host to the IN RS-422 port on the IRC.
Pelco Manual C544M (2/98) 11 3.3.1 Connecting the CM9760-IRC to a CM9760-CC1 Host via Serial GPI A CM9760-IRC can be daisy-chained from a serial GPI already connected to a SerCom port of a CM9760-CC1 (CPU). The wiring is the same as for Section 3.3. Connect the RS-422 OUT port of the serial GPI to the RS-422 IN port of the IRC (refer to Figure 8).
12 Pelco Manual C544M (2/98) 3.5 CONNECTING VCRs TO THE VIDEO MA TRIX BA Y (CM9760-MXB) VCRs must be connected to the CM9760-MXB (Video Matrix Bay). T wo standard coaxial cables are needed: (1) One to run from the VIDEO OUT port on the back of the VCR to the desired IN port on the VMB.
Pelco Manual C544M (2/98) 13 3.6 VCR CONTROL SIGNAL OUTPUTS An IRC has up to 32 D9 female output connections numbered J1 to J32, each able to control four VCRs (refer to Figure 6). Every DB9 output supports four IR control cables. Each IR control cable controls the functions of a single VCR.
14 Pelco Manual C544M (2/98) 4.0 SPECIFICA TIONS Electrical Specifications Operating Voltages: 120 or 230 VAC 50/60 Hz. ± 10%, selectable Power Consumption: 15 vA per control card and communication c.
Pelco Manual C544M (2/98) 15 NOTES.
16 Pelco Manual C544M (2/98) 5.0 WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one (1) year after the date of shipment.
An important point after buying a device Pelco C538M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C538M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C538M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C538M you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C538M will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C538M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C538M.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C538M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C538M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
