Instruction/ maintenance manual of the product C2941M Pelco
Go to page of 24
INST ALLA TION C2941M (8/07) IP3701H-2 and IP3701H-2X IP Color Camera.
.
C2941M (8/07) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2941M (8/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C2941M (8/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C2941M (8/07) Description The IP3701H-2 and IP3701H-2X are high resolution, color video cameras with a built-in 100Base-TX network interface for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ).
C2941M (8/07) 7 Basic System Configurations IMPORT ANT NOTE. PLEASE READ . The network implementations in this document are shown as general representations only and are not intended to show detailed network topologies.
8 C2941M (8/07) Figure 3. Private Network Example Figure 4. Static Network Example IF NOT DHCP , CAMERA CYCLES THROUGH IP ADDRESS RANGE 169.254.200.0 - 169.254.200.255; NETMASK 255.255.0.0 CAMERA CAMERA WEB BROWSER PRIV A TE NETWORK PC ACTS AS SERVER ( ) EXAMPLE 169.
C2941M (8/07) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following modes: T o access one of these modes: 1. Press and hold the reset button. The unit starts cycling through the modes; hold the button for four seconds to access (cycle through) each mode.
10 C2941M (8/07) Installation LENS MOUNTING The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens.
C2941M (8/07) 11 Wiring T ables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector . The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply .
12 C2941M (8/07) T able C. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
C2941M (8/07) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS Set the lens mode selector switch to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1 Vp-p).
14 C2941M (8/07) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus.
C2941M (8/07) 15 Switch Settings Figure 8. DIP Switch Default Settings NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. BLC: Back light compensation. OFF (default setting): Disables the BLC mode.
16 C2941M (8/07) Not Used EDR: Extended dynamic range • Off (Default setting): Disables the EDR mode. • EDR: Enables the EDR mode to help balance a scene with a large dynamic range. Use this feature to improve the picture in washed-out areas.
C2941M (8/07) 17 Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges from bright sunlight to deep shadows has a high dynamic range, while indoor scenes with less contrast have a low dynamic range.
18 C2941M (8/07) T roubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • V erify Cat5 cable connection. • V erify PoE is enabled. • Disconnect the Cat5 cable from the PoE and then reconnect the cable. Power is indicated by the LED.
C2941M (8/07) 19 Image too light • V erify DIP switch settings. • Use a service connector to verify camera operation. Connect one end of the service connector to the BNC service connector on the camera. Connect the other end of the service connector to a monitor .
20 C2941M (8/07) Specifications GENERAL Construction Finish Black polyester powder coat Imaging Device 1/3-inch imager Picture Elements IP3701H-2 768 (H) x 494 (V) IP3701H-2X 752 (H) x 582 (V) Sensing Area 6 mm diagonally Horizontal Resolution 480 TV lines Iris Control Electronic/passive Minimum Illumination 0.
C2941M (8/07) 21 Minimum Web Browser Requirements PC (Pentium ® 4 microprocessor , 1.6 GHz) with Windows ® 98, Windows 2000, Windows XP (or higher), or Mac ® OS X 10.3.9 (or higher) RAM 512 Mbyte Ethernet Card 100 Mbit Web Browser Internet Explorer 5.
22 C2941M (8/07) The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic c.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco C2941M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2941M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2941M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2941M you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2941M will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2941M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2941M.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2941M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2941M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
