Instruction/ maintenance manual of the product C2495M-A Pelco
Go to page of 16
INST ALLA TION ICS-DO111ABK Integrated Camera System MR5000 Series Public V iewing System C2495M-A (1/06).
2 C2495M-A (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
C2495M-A (1/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4 C2495M-A (1/06) Description Designed specifically for the MR5000 Series public viewing system, the ICS-DO111ABK integrated camera system packages a camera and lens into a small, discreet, high-security dome.
C2495M-A (1/06) 5 Installation PREPARE VIDEO AND ELECTRICAL CABLING 1. T emporarily remove the bottom end cap of the MR5000 Series mount if the end cap is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm.
6 C2495M-A (1/06) INSTALL THE ICS-DO111ABK TO THE MR5000 MOUNT Follow the steps below to install the ICS-DO111ABK to the MR5000 mount: 1. Align the adapter plate with the cover. Position the cover so that the notch on the side of the cover faces the back of the MR5000 mount.
C2495M-A (1/06) 7 3. Do the following to install the back box inside the cover of the ICS-DO111ABK: a. Feed the video cable and power wires attached to the ICS-DO111ABK back box through the cover and adapter plate of the ICS- DO111ABK.
8 C2495M-A (1/06) Install Camera 1. Some indoor installations do not require a heater . If the installation does not require a heater , remove the heater board from the camera assembly. T o remove the heater press on an end of the board. 2. 12 VDC operation only: The camera is set for 24 V AC operation at the factory.
C2495M-A (1/06) 9 5. Always make sure the tab on the camera bracket is pointing out of the enclosure (away from the ceiling or wall). Gently squeeze the bracket, place it against the groove inside the back box, and gently release.
10 C2495M-A (1/06) Install Dome and T rim Ring 1. Align the screw holes in the trim ring with those in the Camclosure base. 2. Domes with Liners (only) – Position the viewing window over the lens of the camera by doing the following: a. Loosen the three Phillip screws located in the dome.
C2495M-A (1/06) 11 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness.
12 C2495M-A (1/06) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is.
C2495M-A (1/06) 13 SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1.
14 C2495M-A (1/06) Specifications General Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fi tting and 3/4-inch (1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco C2495M-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2495M-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2495M-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2495M-A you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2495M-A will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2495M-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2495M-A.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2495M-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2495M-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
