Instruction/ maintenance manual of the product C2462M-B Pelco
Go to page of 17
ADDENDUM P elco W or ldwide Headquar t ers 3500 Pelco Way • Clovis , California 93612 USA USA & Canada • T el: 800/289-9100 • Fax: 800/28 9-9150 International • T el: 1-559/292-1 981 • Fax : 1-559/348-112 0 www .
INST ALLA TION C2496M (10/05) 310 Series Camclosure ® Integrated Camera System.
.
C2496M (10/05) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2496M (10/05) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
C2496M (10/05) 5 REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C2496M (10/05) Description The 310 Series Camclosure ® integrated camera system is a track-light design that mounts to a wall or ceiling. The system incorporates a camera and lens package into a small, unobstructive, medium- security enclosure designed for areas subject to vandalism.
C2496M (10/05) 7 • Mounting to ICS310-COND conduit adapter (not supplied) • Mounting to a two-gang electrical box CONDUIT ADAPTER W ALL OR CEILING TWO-GANG ELECTRICAL BOX WA LL OR CEILING ICS310-AP ADAPTER PLA TE (NOT SUPPLIED) 6-32 X 0.
8 C2496M (10/05) CONNECT VIDEO AND POWER 1. Some indoor installations do not require a heater. If the installation does not require a heater, disconnect the heater wiring. a. Remove the cover with the supplied 1/8-inch hollow screwdriver bit. b. Remove the camera from the mounting bracket, and unplug the four -pin heater connector in the base.
C2496M (10/05) 9 ATTACH BASE Release the base locking ring for access to the mounting holes. To attach the base to an adapter plate or conduit adapter, two 6-32 x 1.25-inch tamper-resistant screws are supplied with the adapters. Use the 1/8-inch hollow screwdriver bit supplied with the Camclosure.
10 C2496M (10/05) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit.
C2496M (10/05) 11 SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for optimal performance in lighting conditions where auto iris is required. It is also confi gured with the shutter speed set at 1/60 (NTSC) or 1/50 (PAL) and manual gain set at 6 dB.
12 C2496M (10/05) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is .
C2496M (10/05) 13 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens. To remove the heater board: 1. Disconnect the four-pin heater wiring.
14 C2496M (10/05) Specifications General Pan/T ilt Adjustment Manual; 180° pan; 180° tilt Construction Aluminum base and cover , steel camera mounting bracket Finish Gray polyester powder coat Envi.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco C2462M-B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2462M-B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2462M-B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2462M-B you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2462M-B will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2462M-B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2462M-B.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2462M-B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2462M-B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
