Instruction/ maintenance manual of the product C2461M-A Pelco
Go to page of 16
150 Series Camclosure ® Integrated Camera System with LowLight ™ DSS T echnology C2461M-A (7/03) ® INST ALLA TION/OPERA TION In-Ceiling Mount.
2 C2461M-A (7/03) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 WELCOME ................................................................................
C2461M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
4 C2461M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS150 Series in-ceiling dome system includes a high- resolution, low light, color camera with auto iris and varifocal lens.
C2461M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side.
6 C2461M-A (7/03) Attach to a 4S Deep Electrical Box Refer to Figure 2 for the following steps. The installation instructions assume that the 4S box was previously installed. 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch screws supplied.
C2461M-A (7/03) 7 Install in a Ceiling T ile Refer to Figure 3 for the following steps. 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Use the adapter plate as a template. 2. Punch four screw holes in the ceiling tile.
8 C2461M-A (7/03) Figure 4. Heater Jumper and Camera Connector Locations INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements.
C2461M-A (7/03) 9 Wall Mounting - The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting - The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction.
10 C2461M-A (7/03) Figure 5. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring clockwise/counterclockwise. Refer to Figure 5. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise.
C2461M-A (7/03) 11 ON OFF DIGIT AL SLOW SHUTTER (DSS) Digital slow shutter slows the picture frame rate and increases the camera sensitivity under low light conditions.
12 C2461M-A (7/03) VERTICAL PHASE ADJUSTMENT (24 V AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate ver tical roll reverse the 24 VAC connections on one camera.
C2461M-A (7/03) 13 Figure 6. Dome and Trim Ring Installation REINST ALL THE DOME AND TRIM RING Place the trim ring and dome over the back box. If the dome has a liner , position the viewing window over the lens of the camera. T ighten the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit.
14 C2461M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ± 10%, auto-sensing Power Consumption: 13 watts or less Video Connector: BNC General Operating T emperature: -.
C2461M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2461M 4/03 Preliminary manual for beta testing. C2461M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco C2461M-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2461M-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2461M-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2461M-A you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2461M-A will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2461M-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2461M-A.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2461M-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2461M-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
