Instruction/ maintenance manual of the product C2423M Pelco
Go to page of 28
® SD5BCBW Series Spectra II™ Color/Black & White Dome Systems Operation and Programming Manual C2423M (5/00) P elco • 3500 P elco Wa y • Clovis , CA 93612-5699 USA • www .
CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND WARNINGS ................................................................ 3 OPERA TION ...................................................................................................................
IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes.
OPERA TION POWER-UP DISPLA Y When the Spectra II™ dome is pow ered up, the selected protocol, re vision number , and other inf or mation is display ed on the monitor .
OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iable speed T urbo Mode Preset Mode 0.1 to 80 ° per second, depending on joystick position 150 ° per second 250 ° per second 0.
NOTE: The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. PA TTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command.
AUXILIAR Y OUTPUTS An A UX 1 command from the controller will activate the rela y in the dome and operate the de vice that is connected to the relay . The relay will remain latched until a clear command is issued. An A UX 2 command from the controller will place a ground at the output of A UX 2 to operate the de vice that is connected to it.
PROGRAMMING Programming Guide - Spectra II Color/Black & White Gain/AGC Menu 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Mov e up or down to position cursor or to toggle between selections. Iris Open: Enter Iris Close: Cancel PRESETS The follo wing presets are reserved for special functions .
ACCESSING MAIN MENU (PRESET 95) NOTE: F or American Dynamics controllers with only 32 presets, set s witch SW1-7 on the dome drive in the ON position. When SW1-7 is ON, preset 99 becomes 32 98 becomes.
NOTE: Pattern length is set on the secondar y menu entitled Other . NOTE: To make the pattern r un to its end when an alarm activates it, mak e alar m dwell time longer than pattern length. Thus, if the alarm goes awa y before the end of the pattern, the pattern will continue until the dwell times out.
NOTE: The Spectra II Color/Black and White camera cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. 6. P osition the cursor (>) beside the number of the alarm input for which you w ant to set the pattern. 7. Press the Iris Open button.
AUTO FLIP Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit There are two auto flip modes: On - Auto flip mode is enab led.
AUTO IRIS Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT A uto-Iris Menu A uto-iris mode A uto Auto-iris level 7 Exit Camera Menu.
AUTO IR LEVEL Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <.
NOTE: If backlight compensation is ON and the IR cut filter switches OUT (black and white mode) in normal lighting condi- tions, adjust the A uto IR Level to a darker setting. Ref er to the Auto IR Le vel section. 4. Move the jo ystick up or down to position the cursor ne xt to either Aux 1 mode or A ux 2 mode.
GAIN/AGC Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC&g.
IR FIL TER MODE Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit &l.
NOTE: Programming preset 90 (23) disables the manual limit stops until preset 91 (24) is set. NOTE: On power-up , the auto scan tilt angle will be whatever angle the camera was at when the right scan limit was set. TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1.
LINE SYNC PHASE - The cursor mov es to a numeric value. Move the jo ystick up or down to change the value . Press the Ir is Open b utton to select the choice. The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees.
POWER-UP MODE Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Po w er-Up Menu Pow er Up Default Exit This f eature lets the dome resume a desired condition following pow er-up. The menu includes the following choices.
3. Press the Iris Open button to enter the Other menu. 4. Position the cursor (>) beside Proportional Pan. 5. Press the Iris Open button. The cursor moves to the right, beside the word On or Off . 6. Mov e the joystic k up or down to toggle between On and Off .
SCAN SPEED Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit The scan speed is adjustable from 1-40 degrees per second.
SHUTTER SPEED Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset camera.
SLOW SHUTTER MODE Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset ca.
WHITE BALANCE Main Menu Camera Menu Next Menu White Balance Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit .
ZONE BLANK Main Menu Alarms, Zone Blank Menu Zone Blank Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Alarm resume Off Alarm dwell se.
MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’ s e xter ior surf ace with a nonabrasive cleaning cloth and cleaning agent that is safe f or acrylic.
Effectiv e Pixels NTSC: 768 (H) x 494 (V) P AL: 752 (H) x 582 (V) Horizontal Resolution: >470 TV lines Lens Minimum f-stop: F1.4 Focal Length: 4.1 mm to 73.8 mm optical Zoom Ratio: 18X optical zoom, 4X electronic zoom Digital Slow Shutter: Auto/manual speed selection Horizontal Angle of View: 48 ° (at 4.
An important point after buying a device Pelco C2423M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2423M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2423M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2423M you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2423M will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2423M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2423M.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2423M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2423M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
