Instruction/ maintenance manual of the product C2403M-C Pelco
Go to page of 17
ADDENDUM P elco W or ldwide Headquar t ers 3500 Pelco Way • Clovis , California 93612 USA USA & Canada • T el: 800/289-9100 • Fax: 800/28 9-9150 International • T el: 1-559/292-1 981 • Fax : 1-559/348-112 0 www .
® INST ALLA TION 110 Series Camclosure ® Integrated Camera System C2403M-C (10/05).
2 C2403M-C (10/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C2403M-C (10/05) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
4 C2403M-C (10/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C2403M-C (10/05) 5 Description The ICS110 Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install.
6 C2403M-C (10/05) Installation MOUNTING DIRECTLY TO SURFACE WIRING THROUGH BASE Follow the proceeding steps when feeding wire/cables through the base of the cover and back box: 1. Using the cover as a template, mark one of the large hole positions onto the mounting surface.
C2403M-C (10/05) 7 WIRING THROUGH SIDE CONDUIT Follow the proceeding steps when feeding wire/cables through the side conduit opening of the unit: 1. Attach the cover to the mounting surface (hardware not supplied). Use stainless steel hardware when installing the system outdoors.
8 C2403M-C (10/05) Install Camera 1. Some indoor installations do not require a heater . If the installation does not require a heater , remove the heater board from the camera assembly. T o remove the heater press on an end of the board. 2. 12 VDC operation only: The camera is set for 24 V AC operation at the factory.
C2403M-C (10/05) 9 5. Always make sure the tab on the camera bracket is pointing out of the enclosure (away from the ceiling or wall). Gently squeeze the bracket, place it against the groove inside back box, and gently release.
10 C2403M-C (10/05) Install Dome and T rim Ring 1. Domes with Liners (only) – 2. Align the screw holes in the trim ring with those in the Camclosure base. Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome.
C2403M-C (10/05) 11 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness.
12 C2403M-C (10/05) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) i.
C2403M-C (10/05) 13 SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for optimal performance in lighting conditions where auto iris is required. It is also confi gured with the shutter speed set at 1/60 (NTSC) or 1/50 (PAL) and manual gain set at 6 dB.
14 C2403M-C (10/05) Specifications General Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fi tting and 3/4-inch (1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
® United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco C2403M-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C2403M-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C2403M-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C2403M-C you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C2403M-C will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C2403M-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C2403M-C.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C2403M-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C2403M-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
