Instruction/ maintenance manual of the product C1927M Pelco
Go to page of 34
MX4000 Genex™ Series Simplex Multiplexer Installation/ Operation Manual C1927M (5/99) Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.
2 Pelco Manual C1927M (5/99) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ................................................................ 5 DESCRIPTION ......................................................................................
Pelco Manual C1927M (5/99) 3 LIST OF ILLUSTRA TIONS Figur e Page 1 Stand-Alone Multiplexer ..................................................................................... 7 2 Multiplexers with KBD4000 Keyboard ...................................
4 Pelco Manual C1927M (5/99) (This page intentionally left blank.).
Pelco Manual C1927M (5/99) 5 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
6 Pelco Manual C1927M (5/99) Not only does the number of cameras af fect the time gap, but so does the recording speed. The slower the recording speed, the longer the gap.
Pelco Manual C1927M (5/99) 7 Figure 2. Multiplexers with KBD4000 Keyboard By adding a KBD4000 keyboard to the multiplexer (refer to Figure 2), you can control 1-16 multiplexers from up to 25 feet (7.6 m) away with the cable supplied with the keyboard.
8 Pelco Manual C1927M (5/99) MODELS Color Simplex MX4009CS 9-channel, color simplex multiplexer, NTSC standard, 120 VAC, 60 Hz (UL, cUL, FCC) MX4009CS-X Same as MX4009CS except PAL standard, 230 VAC, .
Pelco Manual C1927M (5/99) 9 INST ALLA TION Unpack and inspect all parts carefully . The following parts are supplied: 1 MX4000 Series multiplexer 1 Rack ear kit 2 Rack ears 4 4-40 x .375-inch pan head screws 4 10-32 x .750-inch pan head screws 1 Power cord 1 6-foot (1.
10 Pelco Manual C1927M (5/99) 3. Attach the rack ears (C) to the multiplexer. The rack ears are universal and can be used on either side of the unit. Attach the ears with the 4-40 x .375-inch screws (D) that are supplied with the ears. Only the two bottom holes on the rack ears are needed for mounting.
Pelco Manual C1927M (5/99) 11 MONITORS Main Monitor - The main monitor can show live video of an individual camera or a sequence of individual cameras, the same as the spot monitor.
12 Pelco Manual C1927M (5/99) 2. For proper recording, the switching rate of the multiplexer between cameras must match that of the VCR. There are two ways to do this: a. One way is with a head switching pulse from the VCR. This is the most reliable way to synchronize the multiplexer and VCR.
Pelco Manual C1927M (5/99) 13 PELCO’S TIME-LAPSE VCRS Y ou can connect one of Pelco’ s T ime-Lapse VCR Models TLR2024, TLR2096, or TLR2168 to the multiplexer as follows (refer to Figure 7): 1. Connect BNC video cable between the VCR connectors on the multiplexer and the VIDEO connectors on the VCR.
14 Pelco Manual C1927M (5/99) 3. Alarm inputs will be programmed in the Programming section for normally open or normally closed operation. Normally closed operation = current flow = alarm switch or r.
Pelco Manual C1927M (5/99) 15 Figure 9. Front Panel, 9-Channel Color Simplex Multiplexer DISPLA Y RECORD Sim DISPLA Y RECORD Sim Figure 10. Front Panel, 16-Channel Color Simplex Multiplexer MUL TIPLEXER WITH MX4000SVR SER VER Refer to Figure 3 in the Applications section for an overview of a typical installation.
16 Pelco Manual C1927M (5/99) T able B. Front Panel Controls Button Operation Function DISPLA Y/ Press once T oggles main monitor display between record, live inputs, and playback from VCR. RECORD In the RECORD mode, the red LED lights. Press for 3 seconds Displays or exits the record setup menu on the main monitor .
Pelco Manual C1927M (5/99) 17 OPERA TION FRONT P ANEL COMMAND Call a camera to the main Press any CAMERA button. monitor. Call a camera to the spot Press any CAMERA button twice. monitor. Set main tracking 1. Go to the Advanced System Setup menu. 2. Press the arrow buttons so the cursor highlights SPOT MONITOR DISPLA Y .
18 Pelco Manual C1927M (5/99) OPERA TION FRONT P ANEL COMMAND Sequence PIP display . 1. Push the button. (Does not work in RECORD 2. Push the SEQUENCE button. or VCR modes) Stop a sequence. Press the SEQUENCE button once or press any CAMERA button to stop a sequence on the main monitor .
Pelco Manual C1927M (5/99) 19 PROGRAMMING Programming allows you to configure the multiplexer for the way that you want your system to operate. The multiplexer automatically selects the most common operating parameters and can be operated without programming it.
20 Pelco Manual C1927M (5/99) 4. When the menu item you desire is highlighted (blinking), do one of the following: • If a menu item has more than one option, press the +/- button to cycle through the options to select the one you want. • If a menu item has only one option, press the +/- button to select it.
Pelco Manual C1927M (5/99) 21 NO CHANGE - This is a pass-through selection in case you unintentionally hit the +/- button. This is not an undo button. Alarm Inputs Refer to the Alarms section for an explanation of normally closed and normally open operation.
22 Pelco Manual C1927M (5/99) Date Format Sets the format for displaying the date on the main monitor. Passwor d Enables or disables password control to access programming menus. Fr ont Panel Control Enables or disables the front panel buttons to operate the multiplexer .
Pelco Manual C1927M (5/99) 23 RECORD SETUP (DISPLA Y/RECORD BUTTON) T o program the VCR recording parameters: 1. Press the DISPLA Y/RECORD button for approximately three seconds. T ype the password, if requested. The Record Setup menu appears. 2. The currently selected menu item blinks.
24 Pelco Manual C1927M (5/99) T able D. VCR T ypes NTSC P AL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUTSA TL VCR 251 GYYR 2100 ASUTSA TL VCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HIT ACHI VTL30E.
Pelco Manual C1927M (5/99) 25 Figure 14. Custom VCR Setup Menu CUSTOM VCR SETUP (DISPLA Y/RECORD BUTTON) T o program the advanced VCR parameters: 1. Press the DISPLA Y/RECORD button for approximately three seconds. The Record Setup menu appears. 2. Make sure the VCR T ype in the Record Setup menu is set to CUSTOM.
26 Pelco Manual C1927M (5/99) CAMERA SETUP (CAMERA BUTTONS) T o program a camera input: 1. Press the desired CAMERA button for approximately three seconds. T ype the password, if requested. The Camera menu appears. A video insert appears that shows what the camera is viewing.
Pelco Manual C1927M (5/99) 27 Activity Detection A camera can be set to respond or not to respond to motion. If enabled, select SET DETECTION MASK to define what part of the camera’s viewing field will be monitored for motion. 5. T o program another camera, press the button for that camera.
28 Pelco Manual C1927M (5/99) 7. T urn activity boxes on or off. T o turn on all activity boxes, use the arrow buttons to choose SET ALL. Press the +/- button. All boxes will contain a symbol as shown in Figure 16. The multiplexer will monitor motion in those boxes.
Pelco Manual C1927M (5/99) 29 HELP MENU The Help menu is accessed from any other menu. 1. Use the up and down arrow buttons in any menu to highlight HELP .
30 Pelco Manual C1927M (5/99) PROGRAMMING THE 4-CAMERA DISPLA YS ( BUTTON) Y ou can program four groups of four cameras each. Each of the four groups can be programmed to include any four cameras. is not available in RECORD mode. T o program the four-camera displays: 1.
Pelco Manual C1927M (5/99) 31 PROGRAMMING MENU DEF AUL TS T able E. Programming Menu Defaults Menu Item Default System Setup T ime Display On T itle Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA) .
32 Pelco Manual C1927M (5/99) TROUBLESHOOTING If you have dif ficulty operating your system, run through the following checklist to see if you can solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server set properly? 4.
Pelco Manual C1927M (5/99) 33 RESET T o reset the multiplexer: 1. Unplug the power cord. 2. Press and hold the VIEW button on the front panel of the multiplexer while you plug the power cord into an electrical outlet. When the Initialization Menu appears, release the VIEW button.
34 Pelco Manual C1927M (5/99) REVISION HISTOR Y Manual # Date Comments C1927M 3/99 Preliminary version released for beta evaluation. 5/99 Original version. ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.
An important point after buying a device Pelco C1927M (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C1927M yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C1927M - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C1927M you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C1927M will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C1927M, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C1927M.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C1927M. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C1927M along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
