Instruction/ maintenance manual of the product C1306M-B (10/06) Pelco
Go to page of 24
ExSite ™ EHXM Series Explosionproof Fixed Sy stem INSTALLATION C1306M-B (10/06).
2 C1306M-B (10/06) Contents List of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safe ty Instruct ions .
C1306M-B (10/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any venti lation open ings. Install in accordance with the manufact urer’ s instructions.
4 C1306M-B (10/06) Getting Started Thank you fo r purchasin g Pelco’ s ExSite ™ EHXM Series explosionproof system. This ma nual incl udes instructions f or installing all the compon ents of the system.
C1306M-B (10/06) 5 Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (140 lb /63.
6 C1306M-B (10/06) CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is a llocated specif ically for an external wash er (not su pplied by Pelco ). • All relays are specifie d for 32 VDC, 0.
C1306M-B (10/06) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are requ ired for Coaxitron control.
8 C1306M-B (10/06) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON ON.
C1306M-B (10/06) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON .
10 C1306M-B (10/06) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF .
C1306M-B (10/06) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON .
12 C1306M-B (10/06) Install the Camera Module T o install the camera mo dule, do th e followi ng: 1. Refer to Figure 4. Loosen t he set screw at the back of the camera encl osure with the pr ovided 1.5 mm A llen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanne r wrench to loosen the ba ck of the camera enclosur e (refer to Figure 5).
C1306M-B (10/06) 13 3. Slide th e camera module i nto the camera enclosure. Refer to Figure 6 to position t he camera modul e properly in the camera e ncl osure. Carefully mate the camer a’ s power connector to the mating connector loca ted inside the camera en closure.
14 C1306M-B (10/06) 4. Models with a wiper: Refer to Figure 8 and do the fo llowing to install the arm of th e wiper: a. Place the su pplied green bushing on t he stud locate d behind th e handle of t he camera module . The bushing should be in the sam e orientatio n as shown in Figure 8.
C1306M-B (10/06) 15 Install the Enclosure and Set Pan Position 1. Check fo r proper seat ing of the po wer module seal. Make sure t he seal is fully seated in t he groove on th e top of the power m odul e. Figure 9. Factory-Installed Power Module Seal 2.
16 C1306M-B (10/06) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nu t and a 21 mm open end wre nch on the tilt shaft (refer to Fig ure 11).
C1306M-B (10/06) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the moun ting holes of the sun shroud with the holes on top of th e camera enclosure. 3. Use the supplied nylo n washers and screws t o secure the sun shroud to th e camera enclosure.
18 C1306M-B (10/06) Maintenance CAMERA MODULE REPLACEMENT T o replace the c amera module, do t he following: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 13 and do the following: a. Loosen the set screw with a 1. 5 mm Allen wrench .
C1306M-B (10/06) 19 3. Models with a wiper: Remove the wiper arm an d the green bushing from the unit (r efer to Figure 14 ). 4. Slide the camera modu le out of the enclosure. 5. Install th e new camera modu le by doing th e following: Slide the came ra module into the camera encl osure.
20 C1306M-B (10/06) 6. Models with a wiper: Refer to Figure 14 and do the following to re install the arm of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module.
C1306M-B (10/06) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input V oltage Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Heater and Defroster Microprocessor con.
22 C1306M-B (10/06) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT95 00 controllers, but not with CM7500, MPT9000 , or KBD9000 cont rollers.
The materials used in the manufacture of this document an d it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco C1306M-B (10/06) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco C1306M-B (10/06) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco C1306M-B (10/06) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco C1306M-B (10/06) you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco C1306M-B (10/06) will certainly help you make a decision on the purchase.
If you already are a holder of Pelco C1306M-B (10/06), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco C1306M-B (10/06).
However, one of the most important roles played by the user manual is to help in solving problems with Pelco C1306M-B (10/06). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco C1306M-B (10/06) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
