Instruction/ maintenance manual of the product 100 Series Pelco
Go to page of 16
100 Series Camclosure ® Integrated Camera System W ith LowLight ™ DSS T echnology C2460M-A (7/03) ® INST ALLA TION/OPERA TION.
2 C2460M-A (7/03) LIST OF ILLUSTRA TIONS Figure Page 1 Installation Directly to a Wall/Ceiling ....................................................................................... ... 5 2 Installation Directly to a Concrete Wall/Ceiling ...........
C2460M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
4 C2460M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS100 Series surface mount dome system includes a high-resolution, low light, color camera with auto iris and varifocal lens.
C2460M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side.
6 C2460M-A (7/03) Figure 3. Installation on a 4S Electrical Box 8-32 X .750 FLAT HEAD SCREW (SUPPLIED) 8-32 X .375 PAN HEAD SCREW (SUPPLIED) WALL OR CEILING ADAPTER PLATE BASE 4S ELECTRICAL BOX Attach Directly to Concrete Wall/Ceiling Refer to Figure 2 for the following steps.
C2460M-A (7/03) 7 Mount to a Plaster Ring Refer to Figure 4 for the following steps. Installation instructions assume that the 4S electrical box and plaster ring were previously installed. 1. Pull video and power wires into the base. 2. Attach the base to the plaster ring.
8 C2460M-A (7/03) Figure 5. Terminal Block for Input Power CONNECT POWER WIRES Depending on the input voltage, connect either the 12 VDC or 24 V AC input power wires to the terminal block inside the base. Refer to Figure 5 for the location of the terminal block.
C2460M-A (7/03) 9 INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements.
10 C2460M-A (7/03) W all Mounting – The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting – The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction.
C2460M-A (7/03) 11 Figure 7. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring. Refer to Figure 7. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise.
12 C2460M-A (7/03) AGC (AUTOMA TIC GAIN CONTROL) AGC automatically adjusts the image to compensate for changes in light levels. ON (Default setting) – Enables the AGC mode.
C2460M-A (7/03) 13 Figure 8. Window Adjustment REINST ALL THE LOWER DOME AND TRIM RING 1. Domes with Liners (only) – Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves.
14 C2460M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ±10%, auto-sensing Power Consumption: 13 watts or less V ideo Connector: BNC General Operating T emperature: -.
C2460M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2460M 4/03 Preliminary manual for beta testing. C2460M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco 100 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco 100 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco 100 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco 100 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco 100 Series will certainly help you make a decision on the purchase.
If you already are a holder of Pelco 100 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco 100 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco 100 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco 100 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
