Instruction/ maintenance manual of the product 684 Peavey
Go to page of 18
O WNER ’ S M ANUAL XR ® 684/XR ® 684+ Stereo Powered Mixer.
2 Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
XR ™ 684/684+ Powered Sound Reinforcement Mixing Console General Description: Congratulations on your purchase of the XR ™ 684/684+ powered mixer . Within one compact unit, we have packed feature after feature, each displaying the latest technology available.
CHANNEL SECTION: CHANNELS 1-4 1. MIC INPUT : XLR balanced, low-impedance channel input optimized for a microphone or other low-level source. Pin 2 is the positive input. Because of the wide range of gain adjustment, signal levels as high as +10 dBV (2.
NOTE: Channels 5-9 contain features that differ from the previous channels. Only those features are mentioned below . For information on features not mentioned please refer to the section for Channels 1-4. CHANNELS 5-6 10. LINE: 1/4" balanced TRS input for line level signals.
17. PRESET : Selects the effect preset from the list below . EFX Presets PRESET NAME TIME/SIZE COLOR/TONE 1 Chamber T ime: 150 to 5,000 ms Damping (High Frequency) 2 Plate T ime: 100 to 4,000 ms Dampi.
26. MAIN LEVEL: This is the master level control for the main mix sent to the Left/Mono and Right output jacks. This control sets the Main level going to the power amp when in Main/Monitor mode (see System Mode #24). A good starting position for this control is the center detent position (12:00).
30. LEFT/MONO OUTPUT : This 1/4" jack provides an output from the Left Main mix to supply external amp/speaker combinations. The level of this signal is determined by the Main Level control. When no plug is connected to the Right Output (#31) then the right signal is mixed with the left, and both can be accessed at the Left/Mono Output.
9 CHANNELS 1-4 HI-Z INPUT MIC PREAMP PA D TONE CONTROL LO MID HI +48V PHANTON LO-Z INPUT CHANNELS 5-6 LINE INPUT MIC PREAMP +48V PHANTON LO-Z INPUT MONITOR SEND CHANNEL GAIN EFX LEVEL TONE CONTROL CHA.
XR ® 684 LEVEL DIAGRAM 10 INPUTS HI-Z (W/P AD) LINE/T APE LO-Z MIC (W/P AD) LO-Z MIC (NO P AD) HI-Z MIC (NO P AD) -60 -50 -40 -30 -20 -10 0 dBu +10 +20 +30 +21 dBu +13.5 dBu -1 1 dBu -12.5 dBu -28 dBu -35 dBu -60 dBu 2 dBu = 0 dBV -15 dB +15 dB EQ XR 684 LEVELS ® MONITOR OUT +22 dBu MAX T APE OUT +10 dBV MAX -10 dBV NOM.
11 Left/Monitor Outputs (Rear) Right/Main Outputs (Rear) Impulse ™ 200 Impulse ™ 200 Mains - Left Mains - Right Mode Switch Out Ke yboard PVM ™ 22 Reactor ® MA Q ™ 150 SP ™ 112M Out T ape P.
Left/Monitor Outputs (Rear) Right/Main Outputs (Rear) Impulse ™ 200 Monitors Mains Mode Switch Depressed (In) PVM ™ 22 Reactor ® Ke yboard Out T ape Player T ape Player In Stereo V oice Module L .
XR ™ 684 SPECIFICA TIONS : Input Specifications: Function Input Z Input Gains Input Levels Bal/ Connector (ohms) control Min** Nominal* Max UnBal. Min setting Lo-Z 2 k Max w/o pad -60 dBu -30 dBu -1 1 dBu Bal. XLR: Pin 1 Gnd, (150 ohms) (50 dB) Pin 2 (+), Pin 3 (-) Channel 1-8 Max.
Frequency Response: Mic Input to L - R Output Line Input to L - R Output T o Power Amplifier Output 20 Hz — 20 kHz +0 dB/-1 dB 20 Hz — 20 kHz +0 dB/-1 dB 20 Hz — 20 kHz +0 dB/-1 dB Graphic Equal.
15 POWER SECTION (400 SC Module with DDT ™ ) Frequency Response: +0, -1 dB, 20 Hz — 20 kHz @ rated power Rated Power: • 210 watts RMS into 4 ohms, both channels driven • 150 watts RMS into 8 ohms, both channels driven • Bridge out 420 watts into 8 ohms* * 8 ohms minimum load for bridge output only T otal Harmonic Distortion: Less than .
34 PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This W arranty Covers Y our Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.
IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed. including the following. 1. Read all safety and operating instructions before using this product. 2. All safety and operating instructions should be retained for future reference.
Features and specifications subject to change without notice. Peavey Electronics Corporation • 71 1 A Street • Meridian • MS • 39301 (601) 483-5365 • F AX (601) 486-1278 • www .
An important point after buying a device Peavey 684 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Peavey 684 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Peavey 684 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Peavey 684 you will learn all the available features of the product, as well as information on its operation. The information that you get Peavey 684 will certainly help you make a decision on the purchase.
If you already are a holder of Peavey 684, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Peavey 684.
However, one of the most important roles played by the user manual is to help in solving problems with Peavey 684. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Peavey 684 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
