Instruction/ maintenance manual of the product 1000 Peavey
Go to page of 12
N ashville 1000 Oper at ing Guide ™.
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Nashville ª 1000 Congratulations on your purchase of the Peavey Nashville ª 1000. As the leader in steel guitar amplification, we are proud to combine innovation and tradition in this new model.
Step 10. T o adjust the overall level, use the Master Gain control. Step 1 1. T o adjust out any undesirable distortion, use the Pre Gain knob. T urning the knob counter- clockwise results in a decreased level, thus reducing the overdriven signal. Any external effects units can also cause the signal to overdrive.
Post EQ Patch (8) Similar to the Pre EQ Patch(4), these jacks are post EQ. The same notes apply . The return level should still be monitored for its strength. In addition, the Post EQ Patch can be taken in and out of the signal path via the footswitch.
NASHVILLE ª 1000 SPECIFICA TIONS: 6 Power Amplifier Section: Rated Power and Load: 300 W RMS into 4 Ohms (with DDT compression) 190 W RMS into 8 Ohms (with DDT compression) 2 Ohms operation not recommend Frequency Response: +0,-3 dB, 20 Hz to 20 kHz @ 250 W RMS into 4 Ohms T otal Harmonic Distortion: Less than 0.
7 Nashville ª 1000 Block Diagram Input Pre Gain Send Return Pre-EQ Effects Loop EQ Low Mid Shift High Pres. Ft. Sw. Switch Logic Send Return Post-EQ Effects Loop Ft.
8 Clean Single Coil Guitar Steel: E9 T uning Steel: C6 T uning Lap Steel Fiddle Nashville ª 1000 Recommended Tone Settings *For CLEAN settings: the MASTER should be a higher setting than the PRE GAIN to a void premature signal clipping.
9 NO TES.
IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water .
PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This W arranty Covers Y our Peavey W arranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.
Peavey Electronics Corporation ¥ 71 1 A Street ¥ Meridian, MS 39301 ¥ U.S.A. (601) 483-5365 ¥ Fax (601) 486-1678 ¥ www .peavey .com ©1999 Printed in U.
An important point after buying a device Peavey 1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Peavey 1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Peavey 1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Peavey 1000 you will learn all the available features of the product, as well as information on its operation. The information that you get Peavey 1000 will certainly help you make a decision on the purchase.
If you already are a holder of Peavey 1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Peavey 1000.
However, one of the most important roles played by the user manual is to help in solving problems with Peavey 1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Peavey 1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
