Instruction/ maintenance manual of the product 1008/I Patton electronic
Go to page of 13
USER MANU AL MODEL 1088/I 10BaseT mDSL Rocket Part# 07M1088I-UM Doc# 0331 1U2-001 Rev . D Revised 10/24/06 SALES OFFICE (301)975-1000 TECHNICAL SUPPORT (301)975-1007 http://www .
T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S Section Page 1.0 W arranty Information .............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service 2.0 General Information ........
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Support at: tel: (301)975-1007 email: support@patton.
3.0 PPP OPERA TIONAL B ACK GROUND PPP is a protocol used for multi-plexed transport over a point- to-point link. PPP operates on all full duplex media, and is a sym- metric peer-to-peer protocol, which can be broken into three main components: 1. A standard method to encapsulate datagrams over serial links; 2.
4 4 . . 0 0 C C O O N N F F I I G G U U R R A A T T I I O O N N There are two modes of operation for the model 1088: Plug-and- Play and self configuration.
9 4.2 CONFIGURING THE HARDW ARE DIP SWITCHES The Model 1088 has two sets of eight DIP switches, which allow configuration for a wide variety of applications.
11 4.2.2 Configuration DIP Switch Set “S3” Use the DIP Switches in Switch S3 to set the DTE Rate (for LAN Bandwidth Allocation), the transmit data sampling point and to reset the unit to its software default settings. The following table summa- rizes default positions of DIP Switch S3.
13 5 5 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N When the Model 1088 has been properly configured, it may be connected to the DSL twisted pair interface, the 10BaseT Ethernet Interface, and the power source. This section describes these connec- tions.
5.4 POWER CONNECTION Universal AC Power (100-240V AC) The Model 1088 uses a 5VDC, 2A universal input 100-240V AC, power supply (center pin is +5V). The universal input power supply has a male IEC-320 power entry connector . This power supply con- nects to the Model 1088 by means of a barrel jack on the rear panel.
CRC 9 pulses = Detected LAN receive frame(s) too large 10 pulses = Detected LAN receive frame(s) not octet aligned 1 1 pulses = Detected LAN receive frame(s) with bad CRC 10BT Link (Active Green) Solid green indicates that the 10BaseT Ethernet interface has detected a valid SQE heartbeat, signifying a valid 10BaseT con- nection.
transmitting data and the pattern generator is enabled on one end of the link, the far end will begin receiving unframed packets and assume that the line has gone down. During test modes, the pattern generator is forced to time out before it can cause the DSL link to go down.
2. If the above test indicates no errors are present, move the test switch V .52 toggle switch UP , activating the “51 1/E” test with intentional errors present.
APPENDIX B P A TTON ELECTRONICS MODEL 1088 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Electronics Model # Description 1088/I ..............................10BaseT mDSL Rocket (CAP) 48V -PSM .........................DC Power Supply Module 08055DCUI .
An important point after buying a device Patton electronic 1008/I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1008/I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1008/I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1008/I you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1008/I will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1008/I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1008/I.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1008/I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1008/I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
