Instruction/ maintenance manual of the product 1000RC Patton electronic
Go to page of 9
USER MANUAL MODEL 1000RC Asynchronous Short Range Modem: Dual Rack Mount Card SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 Part# 07M1000RC-B Doc# 05201 1UB Revised 4/30/96.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1000RC components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
3.2 FRONT CARD CONFIGURA TION The Model 1000RC contains two sets of configuration straps which allow you to set the function of “Carrier Detect” output. Since the Model 1000RC contains two modems, each unit can be configured separately: Jumper 1 (JB1) controls Unit A, while Jumper 2 (JB2) controls Unit B.
JB2 Position 1&2 = Line A Shield Connected to Frame Ground Position 2&3 = No Shield JB4 Position 1&2 = Line B Shield Connected to Frame Ground Position 2&3 = No Shield SGND & FRGND (JB5) In position 1&2, this strap links signal ground and frame ground through a 100 Ohm, 1/2 W resistor .
Switching the Power Supply On and Off The power switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow . Since the Model 1000R16P is a “hot swappable” rack, it is not necessary for any cards to be installed before switching on the power supply .
RJ-45 Cable SIGNAL PIN# PIN# SIGNAL GND † 2 -----------------------7 GND † RCV - 3 -----------------------5 XMT - XMT+ 4 -----------------------6 RCV+ XMT - 5 -----------------------3 RCV - RCV+ 6 -----------------------4 XMT+ GND † 7 -----------------------2 GND † † Connection to ground is optional 11 5.
APPENDIX A SPECIFICA TIONS T ransmission Format : Asynchronous Data Rate : 0 to 19.2 Kbps Surge Protection: 600W power dissipation at 1 mS Control Signal : DCE Mode: CTS (Pin 8) turns ON immediately a.
APPENDIX D INTERF ACE SETTINGS & ORIENT A TION P A TT ON MODULAR INTERF ACE - 10 Wire RJ-45 Contact Number Circuit Description 1 N/A Not Used 2 125 DSR 3 109 Received Line Signal Indicator (CD) 4 .
An important point after buying a device Patton electronic 1000RC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1000RC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1000RC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1000RC you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1000RC will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1000RC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1000RC.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1000RC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1000RC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
