Instruction/ maintenance manual of the product HCA 806A Parasound
Go to page of 12
-1- P o w e r Power HCA-806A High Current Multi Amplifier HCA-806A High Current Multi Amplifier Current Overload 1 2 3 4 5 6 AC Line Standby Normal O W N E R ' S M A N U A L HCA- 8 0 6A S i x Ch .
-2- T able of Contents Important Safety Instructions ........................................................................................ 3 Figure #1 and #2 HCA-806A Front and Rear P anel Drawings ..................................... 4 Intr oduction .
-3- IMPORTANT SAFETY INSTRUCTIONS The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of “dangerous voltage” inside the product that may constitute a risk of electric shock.
-4- HCA-806A Front and Rear Panel Controls Figure #2 HCA-806A Front Panel Controls Figure #1 HCA-806A Front Panel Controls HCA - 806A High Current Multi-Amplifier Parasound Products, Inc San Francisco, CA U.
-5- Introduction Congratulations on your purchase of this precision audio component and thank you for your selection of Parasound. Please take a few moments to read these instructions so that you may fully understand the capabilities of your new Parasound power amplifier.
-6- Input Connections and Switch Settings for the HCA-806A Refer to Figure #2 Six Channel Operation The six channel mode of your HCA-806A can power the six speakers required for a complete home theater: Front left and right, surround left and right, center channel, and subwoofer.
-7- Multi-Zone Stereo Operation Refer to Figure #2 You can switch your HCA-806A to reproduce a single stereo source through up to three pairs of stereo channels via input cables connected to channels 1 and 2 input jacks only. This permits a neater and less confusing hookup.
-8- Mono Bridging — Channels 3+4 and 5+6 When you bridge channels 3+4 and/or 5+6, your speakers are connected to the bridged channels differently. You bridge by using the red + terminals of the adjacent channel pairs only.
-9- Operating Your HCA-806A Power Switch Manual Turn On Press the upper side to turn the unit on manually; press the lower side to turn the unit off. Automatic Turn On When the power switch is in the off position, the power amplifier can be turned on with an external DC voltage applied at the DC trigger connector on the rear panel.
-10- In Case of Trouble If you suspect a problem with this unit, first recheck all your connections. If only one channel is inoperative, the trouble may be caused by another component or even a defective hookup cable.
-11- Parasound HCA-806A Specifications Continuous Power Output > 80 watts RMS x 6, 20 Hz - 20 kHz, 8 Ω , all channels driven > 120 watts RMS x 6, 20 Hz - 20 kHz, 4 Ω , all channels driven Co.
-12- © 1997 Parasound Products, Inc. Parasound Limited Warranty (USA only) Your Parasound HCA-806 amplifier is covered by a limited warranty against defects in materials and workmanship for a period of two years from date of purchase. This warranty is provided by the Parasound dealer where the unit was purchased.
An important point after buying a device Parasound HCA 806A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Parasound HCA 806A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Parasound HCA 806A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Parasound HCA 806A you will learn all the available features of the product, as well as information on its operation. The information that you get Parasound HCA 806A will certainly help you make a decision on the purchase.
If you already are a holder of Parasound HCA 806A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Parasound HCA 806A.
However, one of the most important roles played by the user manual is to help in solving problems with Parasound HCA 806A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Parasound HCA 806A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
