Instruction/ maintenance manual of the product 9783 Paradyne
Go to page of 233
FrameSaver DSL 9783 USER’S GUIDE Document No. 9783-A2-GB20-00 July 2000.
A 9783-A2-GB20-00 July 2000 Copyright E 2000 Paradyne Corporation All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law .
i 9783-A2-GB20-00 July 2000 Contents About This Guide H Purpose and Intended Audience vii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Document Organization vii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents ii 9783-A2-GB20-00 July 2000 4 Configuration Options H Overview 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Using the Easy Install Feature 4-3 . . . . . . . . . . . . . . .
Contents iii 9783-A2-GB20-00 July 2000 6 Operation and Maintenance H Displaying System Information 6-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Viewing LEDs and Control Leads 6-3 . . . . . . . . . . . . . . . . . . . .
Contents iv 9783-A2-GB20-00 July 2000 8 T roubleshooting H Problem Indicators 8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H Resetting the Unit and Restoring Communication 8-3 . . . . . . . . . . . . .
Contents v 9783-A2-GB20-00 July 2000 10 Setting Up Network Health for FrameSaver Devices H Installation and Setup of Network Health 10-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . H Discovering FrameSaver Elements 10-3 . . . . . . . . . . .
Contents vi 9783-A2-GB20-00 July 2000 C Connectors, Cables, and Pin Assignments H Rear Panel C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H DSL Network Interface Cable C-2 . . . . . . . .
vii 9783-A2-GB20-00 July 2000 About This Guide Purpose and Intended Audience This document contains information that applies to the FrameSaver DSL 9783. It is intended for system designers, engineers, administrators, and operators who are familiar with the functional operation of digital data communications equipment and frame relay networks.
About This Guide viii 9783-A2-GB20-00 July 2000 Section Description Chapter 8 T roubleshooting. Provides device problem resolution, alarm, and other information, as well as troubleshooting and test procedures. Chapter 9 Setting Up OpenLane for FrameSaver Devices.
About This Guide ix 9783-A2-GB20-00 July 2000 Pr oduct-Related Documents Document Number Document Title Paradyne FrameSaver Documentation: 9000-A2-GB20 Configuring Frame Relay Service Over DSL 9783-A2.
About This Guide x 9783-A2-GB20-00 July 2000 Conventions Used Convention Used When Used Italic T o indicate variable information (e.g., DLCI nnnn ) . Menu selection sequence T o provide an abbreviated method for indicating the selections to be made from a menu or selections from within a menu before performing a procedural step.
1-1 9783-A2-GB20-00 July 2000 About the FrameSaver DSL Unit 1 This chapter includes the following: H System Overview H FrameSaver DSL Features and Benefits H FrameSaver DSL Feature Sets — Basic Feat.
About the FrameSaver DSL Unit 1-2 9783-A2-GB20-00 July 2000 FrameSaver DSL Featur es and Benefits Large-scale deployment of frame relay services over DSL-based access networks is possible with the innovative FrameSaver DSL, which provides important advantages for frame relay service providers.
About the FrameSaver DSL Unit 1-3 9783-A2-GB20-00 July 2000 H Advanced SLM and reporting feature set includes all of the diagnostic feature set, plus: — CIR relationship statistics — FDR/DDR (T ru.
About the FrameSaver DSL Unit 1-4 9783-A2-GB20-00 July 2000 An advanced SLM and reporting feature set can be activated on command with the SL V key . In the base configuration, comprehensive Layer 1 and 2 instrumentation allows service providers to isolate, diagnose, and correct problems remotely from their NOC.
About the FrameSaver DSL Unit 1-5 9783-A2-GB20-00 July 2000 The following diagram shows the FrameSaver DSL unit in a frame relay network. Frame Rela y CPE Router/FRAD DSL A TM Access Network F rameSav.
About the FrameSaver DSL Unit 1-6 9783-A2-GB20-00 July 2000 FrameSaver DSL Featur e Sets Depending upon the model ordered, the FrameSaver DSL unit has the basic FrameSaver frame relay and diagnostic capability , or it is enhanced with additional SL V (Service Level V erification) reporting capability .
About the FrameSaver DSL Unit 1-7 9783-A2-GB20-00 July 2000 T o obtain an activation certificate, provide the model number (9783), your OpenLane system license key number , and the number of FrameSaver units whose SL V capability is to be activated.
About the FrameSaver DSL Unit 1-8 9783-A2-GB20-00 July 2000 Basic Features The FrameSaver DSL unit provides the following features: H Easy Installation. When AutoBaud is used, no configuration is required. SNMP options may be modified if desired to provide security and enable traps.
About the FrameSaver DSL Unit 1-9 9783-A2-GB20-00 July 2000 H Dual Flash Memory . Allows software upgrades while the unit is up and running. T wo software loads can be stored and implemented at the user ’ s discretion. H Multiplexed Management PVCs.
About the FrameSaver DSL Unit 1-10 9783-A2-GB20-00 July 2000 H LMI Packet Capture. Provides a way of uploading data that has been captured in a trace file so the data can be uploaded and transferred to a Network Associates Snif fer for analysis, or viewed via the menu-driven user interface.
About the FrameSaver DSL Unit 1-1 1 9783-A2-GB20-00 July 2000 OpenLane SLM System Being standards-based, the OpenLane SLM (Service Level Management) system can be used with other management applications like HP OpenV iew or IBM’s NetV iew . OpenLane includes HP OpenView adapters for integrating OpenLane features with the OpenView W eb interface.
About the FrameSaver DSL Unit 1-12 9783-A2-GB20-00 July 2000.
2-1 9783-A2-GB20-00 July 2000 User Interface and Basic Operation 2 This chapter explains how to access, use, and navigate the menu-driven user interface.
User Interface and Basic Operation 2-2 9783-A2-GB20-00 July 2000 Logging On Start a session using one of the following methods: H T elnet session via: — An in-band management channel through the frame relay network (frame relay network service provider).
User Interface and Basic Operation 2-3 9783-A2-GB20-00 July 2000 If your login was . . . Then the . . . V alid Main Menu appears. Begin your session. NOTE: If your login is valid, but access is denied, there are two currently active sessions. Invalid Message, Invalid Password , appears on line 24, and the Login screen is redisplayed.
User Interface and Basic Operation 2-4 9783-A2-GB20-00 July 2000 Main Menu Entry to all of the FrameSaver unit’s tasks begins at the Main Menu, which has six menus or branches. The Access Level at the top of the screen only appears when security has been set up.
User Interface and Basic Operation 2-5 9783-A2-GB20-00 July 2000 Scr een W ork Ar eas There are two user work areas: H Screen area – Where you input information into fields. H Function keys area – Where you perform specific screen functions. main /config/system/slv 9783 .
User Interface and Basic Operation 2-6 9783-A2-GB20-00 July 2000 Navigating the Scr eens Y ou can navigate the screens by: H Using keyboard keys. H Switching between the two screen work areas using function keys. Keyboard Keys Use the following keyboard keys to navigate within the screen area: Press .
User Interface and Basic Operation 2-7 9783-A2-GB20-00 July 2000 Function Keys All function keys (located in the lower part of the screen; see the example in Screen Work Areas on page 2-5) operate the same way throughout the screens. They are not case-sensitive, so upper- or lowercase letters can be used interchangeably .
User Interface and Basic Operation 2-8 9783-A2-GB20-00 July 2000 Selecting from a Menu " Procedur e T o select from a menu: 1. T ab or press the down arrow key to position the cursor on a menu selection, or press the up arrow key to move the cursor to the bottom of the menu list.
User Interface and Basic Operation 2-9 9783-A2-GB20-00 July 2000 Selecting a Field Once you reach the desired menu or screen, select a field to view or change, or issue a command. Press the T ab or right arrow key to move the cursor from one field to another .
User Interface and Basic Operation 2-10 9783-A2-GB20-00 July 2000 This page intentionally left blank..
3-1 9783-A2-GB20-00 July 2000 Configuration Procedur es 3 This chapter includes the following: H Basic Configuration — Configuration Option Areas — Accessing and Displaying Configuration Options .
Configuration Procedures 3-2 9783-A2-GB20-00 July 2000 Basic Configuration Configuration option settings determine how the FrameSaver DSL Unit operates. Use the unit’s Configuration Edit/Display menu to display or change configuration option settings.
Configuration Procedures 3-3 9783-A2-GB20-00 July 2000 Configuration Option Areas The FrameSaver unit arrives with configured factory default settings, which are located in the Factory Default Configuration option area.
Configuration Procedures 3-4 9783-A2-GB20-00 July 2000 Accessing and Displaying Configuration Options T o access and display configuration options, load (copy) the applicable configuration option set into the edit area. " Procedur e T o load a set of configuration options for editing: 1.
Configuration Procedures 3-5 9783-A2-GB20-00 July 2000 Changing Configuration Options " Procedur e T o change configuration option settings: 1. From the Configuration Edit/Display menu, select a set of configuration options and press Enter . For example: Configuration → PVC Connections 2.
Configuration Procedures 3-6 9783-A2-GB20-00 July 2000 Saving Configuration Options When changes to the configuration options are complete, use the S ave function key to save your changes to either the Current, Customer 1, or Customer 2 configuration areas.
4-1 9783-A2-GB20-00 July 2000 Configuration Options 4 Overview A variety of configuration options are provided, but not ordinarily required. The recommended configuration tool for the FrameSaver DSL unit is the OpenLane Service Level Management system.
Configuration Options 4-2 9783-A2-GB20-00 July 2000 H Setting Up Management and Communication Options — Configuring Node IP Information — Configuring Management PVCs — Configuring General SNMP M.
Configuration Options 4-3 9783-A2-GB20-00 July 2000 Using the Easy Install Featur e An Easy Install screen is provided for custom configurations, but is not required for normal installation. The Easy Install feature allows minimal configuration of the FrameSaver DSL Unit.
Configuration Options 4-4 9783-A2-GB20-00 July 2000 T able 4-1. Easy Install Configuration Options (1 of 2) Node IP Address Possible Settings: 001.000.000.000 – 223.255.255.255, Clear Default Setting: Clear (000.000.000.000) Specifies the IP address needed to access the node.
Configuration Options 4-5 9783-A2-GB20-00 July 2000 T able 4-1. Easy Install Configuration Options (2 of 2) TS Access (VCI) Possible Settings: 32–255 Default Setting: 0 Specifies the VCI on the network interface to be used for troubleshooting by the service provider .
Configuration Options 4-6 9783-A2-GB20-00 July 2000 Setting Up So the Router Can Receive RIP Using the system’s standard Routing Information Protocol (RIP) feature, routing information is passed to the router over the management PVC, so the router can learn routes to FrameSaver devices.
Configuration Options 4-7 9783-A2-GB20-00 July 2000 Configuration Option T ables Configuration option descriptions contained in this chapter are in menu order , even though this may not be the order in which you access each when configuring the unit. The following configuration option tables are included: H T able 4-2.
Configuration Options 4-8 9783-A2-GB20-00 July 2000 Configuring Frame Relay and LMI for the System Select Frame Relay and LMI from the System menu to display or change the Frame Relay and LMI options for the entire system (see T able 4-2). Main Menu → Configuration → System → Frame Relay and LMI T able 4-2.
Configuration Options 4-9 9783-A2-GB20-00 July 2000 T able 4-2. System Frame Relay and LMI Options (2 of 2) LMI Error Event (N2) Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 Default Setting: 3 Configures the LMI-defined N2 parameter , which sets the number of errors that can occur on the LMI link before an error is reported.
Configuration Options 4-10 9783-A2-GB20-00 July 2000 Configuring Service Level V erification Options SL V options are selected from the System menu (see T able 4-3).
Configuration Options 4-1 1 9783-A2-GB20-00 July 2000 T able 4-3. Service Level V erification Options (2 of 2) SL V T imeout Clearing Event Threshold Available Settings: 1, 2, 3, 4 . . . 20 Default Setting: 1 Specifies the number of consecutive SL V messages that must be received before the DLCI Inactive status is cleared.
Configuration Options 4-12 9783-A2-GB20-00 July 2000 Configuring General System Options Select General from the System menu to configure the general system configuration options (see T able 4-4). Main Menu → Configuration → System → General T able 4-4.
Configuration Options 4-13 9783-A2-GB20-00 July 2000 Configuring the Physical Interfaces Characteristics for the following physical interfaces can be configured: H Network Interface H User Data Port C.
Configuration Options 4-14 9783-A2-GB20-00 July 2000 Configuring the User Data Port Select Physical from the Data Ports menu to configure the physical characteristics for the user data port (see T able 4-6). Main Menu → Configuration → Data Ports → Physical T able 4-6.
Configuration Options 4-15 9783-A2-GB20-00 July 2000 T able 4-6. Data Port Physical Interface Options (2 of 2) Monitor DTR Possible Settings: Enable, Disable Default Setting: Enable Specifies whether the state of the DTE Ready (DTR) circuit on the user data port will be used to determine when valid data communication is possible with the DTE.
Configuration Options 4-16 9783-A2-GB20-00 July 2000 Configuring Frame Relay for the Data Port Select Frame Relay from the Data Ports menu to display or change the Frame Relay options (see T able 4-7). Main Menu → Configuration → Data Ports → Frame Relay T able 4-7.
Configuration Options 4-17 9783-A2-GB20-00 July 2000 T able 4-7. Data Port Frame Relay Options (2 of 2) LMI Clearing Event (N3) Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 Default Setting: 1 Configures the LMI-defined N3 parameter , which sets the number of error-free messages that must be received before clearing an error event.
Configuration Options 4-18 9783-A2-GB20-00 July 2000 Configuring A TM for the Network Interface Select A TM from the Network menu to display or change the A TM options (see T able 4-8).
Configuration Options 4-19 9783-A2-GB20-00 July 2000 Configuring Cir cuit and DLCI Records Circuit and DLCI records can be created and modified, and PVCs created based on existing DLCIs, using the Net.
Configuration Options 4-20 9783-A2-GB20-00 July 2000 T able 4-9. DLCI Record Options (2 of 3) DLCI T ype Possible Settings: Standard, Multiplexed Default Setting: Multiplexed Specifies whether the DLCI is standard or multiplexed.
Configuration Options 4-21 9783-A2-GB20-00 July 2000 T able 4-9. DLCI Record Options (3 of 3) Excess Burst Size (Bits) Specifies the maximum amount of data in bits that the network may accept beyond the CIR without discarding frames.
Configuration Options 4-22 9783-A2-GB20-00 July 2000 Configuring PVC Connections The Auto-Configuration feature automatically configures PVC connections and their DLCI Records.
Configuration Options 4-23 9783-A2-GB20-00 July 2000 T able 4-10. PVC Connection Options (2 of 2) Destination Link Possible Settings: Net1-FR1 Default Setting: Initially blank; no default. Specifies the frame relay interface used as the destination link; the to end of a from-to link.
Configuration Options 4-24 9783-A2-GB20-00 July 2000 Setting Up Management and Communication Options The following options can be selected from the Management and Communication menu: H Node IP Options.
Configuration Options 4-25 9783-A2-GB20-00 July 2000 T able 4-1 1. Node IP Options (1 of 3) Node IP Address Possible Settings: 001.000.000.000 – 223.255.255.255, Clear Default Setting: Clear (000.000.000.000) Specifies the IP address needed to access the node.
Configuration Options 4-26 9783-A2-GB20-00 July 2000 T able 4-1 1. Node IP Options (2 of 3) Default IP Destination Possible Settings: None, COM, Ethernet, PVCname Default Setting: None Specifies an IP destination to route data that does not have a specifically defined route.
Configuration Options 4-27 9783-A2-GB20-00 July 2000 T able 4-1 1. Node IP Options (3 of 3) TS Access Management Link Available Settings: None, PVCname Default Setting: None Specifies a troubleshooting management link for the special needs of network service providers.
Configuration Options 4-28 9783-A2-GB20-00 July 2000 Configuring Management PVCs Select Management PVCs to define inband management links by adding or changing Management PVCs (see T able 4-12 ). First, DLCI records must have been configured for the interface where the Management PVC will reside.
Configuration Options 4-29 9783-A2-GB20-00 July 2000 T able 4-12. Management PVC Options (2 of 3) Intf Subnet Mask Possible Settings: Node-Subnet-Mask, Calculate, Special ( nnn .
Configuration Options 4-30 9783-A2-GB20-00 July 2000 T able 4-12. Management PVC Options (3 of 3) Primary DLCI Possible Settings: 16 – 1007 Default Setting: Initially blank; no default. Specifies the DLCI number used for the management PVC after the frame relay interface is selected.
Configuration Options 4-31 9783-A2-GB20-00 July 2000 Configuring General SNMP Management Select General SNMP Management to add, change, or delete the information needed to allow the FrameSaver unit to be managed as an SNMP agent by the NMS supporting the SNMP protocols (see T able 4-13).
Configuration Options 4-32 9783-A2-GB20-00 July 2000 T able 4-13. General SNMP Management Options (2 of 2) Name 2 Access Possible Settings: Read, Read/Write Default Setting: Read Specifies the type of access allowed to the objects in the MIB. This is the type of access allowed for external SNMP managers accessing MIB objects using Community Name 2.
Configuration Options 4-33 9783-A2-GB20-00 July 2000 Configuring T elnet and/or FTP Session Support T elnet and FTP options control whether a T elnet or FTP (File T ransport Protocol) session is allowed through an interconnected IP network and the access security applicable to the session.
Configuration Options 4-34 9783-A2-GB20-00 July 2000 T able 4-14. T elnet and FTP Session Options (2 of 3) Session Access Level Possible Settings: Level-1, Level-2, Level-3 Default Setting: Level-1 Specifies the highest security level allowed when accessing the menu-driven user interface via a T elnet session.
Configuration Options 4-35 9783-A2-GB20-00 July 2000 T able 4-14. T elnet and FTP Session Options (3 of 3) FTP Session Possible Settings: Enable, Disable Default Setting: Enable Determines whether the system responds as a server when an FTP (file transfer protocol) client on an interconnected IP network requests an FTP session.
Configuration Options 4-36 9783-A2-GB20-00 July 2000 Configuring SNMP NMS Security Select SNMP NMS Security from the Management and Communication menu to display , add, or change SNMP security configuration options for the FrameSaver unit to set up trap managers (see T able 4-15).
Configuration Options 4-37 9783-A2-GB20-00 July 2000 Configuring SNMP T raps Select SNMP T raps from the Management and Communication menu to configure SNMP traps when a trap is generated (see T able 4-16).
Configuration Options 4-38 9783-A2-GB20-00 July 2000 T able 4-16. SNMP T raps Options (2 of 3) Initial Route Destination Possible Settings: AutoRoute, Ethernet, COM, PVCname Default Setting: AutoRoute Specifies the initial route used to reach the specified T rap Manager .
Configuration Options 4-39 9783-A2-GB20-00 July 2000 T able 4-16. SNMP T raps Options (3 of 3) Link T raps Possible Settings: Disable, Up, Down, Both Default Setting: Both Determines whether SNMP linkDown or linkUp traps are sent to the currently configured trap manager(s).
Configuration Options 4-40 9783-A2-GB20-00 July 2000 Configuring the Ethernet Port Select Ethernet Port from the Management and Communication menu to configure the Ethernet port (see T able 4-17). Main Menu → Configuration → Management and Communication → Ethernet Port T able 4-17.
Configuration Options 4-41 9783-A2-GB20-00 July 2000 T able 4-17. Ethernet Port Options (2 of 2) Proxy ARP Possible Settings: Enable, Disable Default Setting: Disable Determines whether the port can be used to supply the MAC (Media Access Control) address of a FrameSaver unit at the other end of a PVC using ARP (Address Resolution Protocol).
Configuration Options 4-42 9783-A2-GB20-00 July 2000 Configuring the Communication Port Select Communication Port from the Management and Communication menu to display or change the communication port configuration options (see T able 4-18). Main Menu → Configuration → Management and Communication → Communication Port T able 4-18.
Configuration Options 4-43 9783-A2-GB20-00 July 2000 T able 4-18. Communication Port Options (2 of 4) Stop Bits Possible Settings: 1, 2 Default Setting: 1 Determines the number of stop bits used for the COM port. 1 – Provides one stop bit. 2 – Provides two stop bits.
Configuration Options 4-44 9783-A2-GB20-00 July 2000 T able 4-18. Communication Port Options (3 of 4) Inactivity Timeout Possible Settings: Enable, Disable Default Setting: Enable Determines whether a user session is disconnected after a specified time of inactivity (no keyboard activity).
Configuration Options 4-45 9783-A2-GB20-00 July 2000 T able 4-18. Communication Port Options (4 of 4) RIP Possible Settings: None, Standard_out Default Setting: None Specifies which Routing Information Protocol (RIP) is used to enable routing of management data between devices.
Configuration Options 4-46 9783-A2-GB20-00 July 2000 Configuring the COM Port to Support an External Modem Select External Modem (Com Port) to display or change the configuration options that control call processing for an external device attached to the COM port (see T able 4-19).
5-1 9783-A2-GB20-00 July 2000 Security and Logins 5 This chapter includes the following: H Limiting Access H Controlling Asynchronous T erminal Access H Controlling External COM Port Device Access H C.
Security and Logins 5-2 9783-A2-GB20-00 July 2000 Limiting Access The FrameSaver unit provides access security on the following interfaces: H Asynchronous (async) terminal H T elnet H FTP H SNMP Up to.
Security and Logins 5-3 9783-A2-GB20-00 July 2000 " Procedur e T o limit asynchronous terminal access to the menu-driven user interface: 1. Select the Communication Port options. Main Menu → Configuration → Management and Communication → Communication Port 2.
Security and Logins 5-4 9783-A2-GB20-00 July 2000 Contr olling External COM Port Device Access Dial-in access can be controlled when an external device (modem) is connected to the unit’s communication (COM) port. The External Device Commands option must be set to A T .
Security and Logins 5-5 9783-A2-GB20-00 July 2000 Limiting T elnet Access T elnet access can be limited by: H Disabling T elnet access completely . H Requiring a login for T elnet sessions that are not on the TS Management Link. H Assigning an access level for T elnet sessions.
Security and Logins 5-6 9783-A2-GB20-00 July 2000 Limiting FTP Access FTP access can be limited by: H Disabling FTP access completely . H Requiring a user ID and password to login. H Limiting FTP bandwidth. " Procedur e T o limit FTP access when the session is not on the TS Management Link: 1.
Security and Logins 5-7 9783-A2-GB20-00 July 2000 Limiting T elnet or FTP Access Over the TS Management Link " Procedur e T o limit T elnet or FTP access when the session is on the TS Management Link: 1. Select the T elnet and FTP Session options.
Security and Logins 5-8 9783-A2-GB20-00 July 2000 Contr olling SNMP Access The FrameSaver unit supports SNMP V ersion 1, which provides limited security through the use of community names. There are three methods for limiting SNMP access: H Disabling SNMP access.
Security and Logins 5-9 9783-A2-GB20-00 July 2000 Assigning SNMP Community Names and Access Levels The FrameSaver unit supports the SNMP protocol and can be managed by an SNMP manager . SNMP manager access can be limited by: H Assigning the SNMP community names that are allowed to access the FrameSaver unit’s Management Information Base (MIB).
Security and Logins 5-10 9783-A2-GB20-00 July 2000 Limiting SNMP Access Through IP Addr esses An additional level of security is provided by: H Limiting the IP addresses of NMSs that can access the FrameSaver unit. H Performing validation checks on the IP address of SNMP management systems attempting to access the FrameSaver unit.
Security and Logins 5-1 1 9783-A2-GB20-00 July 2000 See Configuring SNMP NMS Security in Chapter 4 , Configuration Options, for more information about SNMP NMS Security configuration options. Cr eating a Login A login is required if security is enabled.
Security and Logins 5-12 9783-A2-GB20-00 July 2000 See Configuring SNMP NMS Security in Chapter 4 , Configuration Options, for more information about security configuration options. Modifying a Login Logins are modified by deleting the incorrect login and creating a new one.
6-1 9783-A2-GB20-00 July 2000 Operation and Maintenance 6 This chapter includes the following information: H Displaying System Information H Viewing LEDs and Control Leads — LED Descriptions — Con.
Operation and Maintenance 6-2 9783-A2-GB20-00 July 2000 Displaying System Information Use the Identity screen to view identification information about the FrameSaver unit. This information is useful if you are purchasing additional or replacement units and/or making firmware upgrades.
Operation and Maintenance 6-3 9783-A2-GB20-00 July 2000 V iewing LEDs and Contr ol Leads The FrameSaver DSL unit’s faceplate includes LEDs ( light-emitting diodes) that provide status on the unit and its interfaces. The central site unit (supporting 64 PVCs) is shown.
Operation and Maintenance 6-4 9783-A2-GB20-00 July 2000 LED Descriptions The following table identifies the alarms that cause the Alarm LED to light. See T able 6-2 and T able 6-3 for network and user data port interface LED information.
Operation and Maintenance 6-5 9783-A2-GB20-00 July 2000 T able 6-2. Network Interface LEDs Label Indication Color What It Means AT M A TM Link Status Multi- colored Y ellow – The A TM link is down. colored Green – The A TM link is up. OFF The FrameSaver unit is in leased line OFF – The FrameSaver unit is in leased line mode.
Operation and Maintenance 6-6 9783-A2-GB20-00 July 2000 Control Lead Descriptions In addition to the LEDs, certain control leads can be monitored through the Display LEDs and Control Leads screen.
Operation and Maintenance 6-7 9783-A2-GB20-00 July 2000 Device Messages These messages appear in the messages area at the bottom of the screens. All device messages are listed in alphabetical order . T able 6-5. Device Messages (1 of 5) Message What It Indicates What T o Do Access level is n , Read-only .
Operation and Maintenance 6-8 9783-A2-GB20-00 July 2000 T able 6-5. Device Messages (2 of 5) Message What T o Do What It Indicates Duplicate DLCI Number DLCI number entered is not unique for the frame relay link. No action is needed; previous contents of the DLCI number field is restored.
Operation and Maintenance 6-9 9783-A2-GB20-00 July 2000 T able 6-5. Device Messages (3 of 5) Message What T o Do What It Indicates Limit of six Login IDs reached An attempt to enter a new login ID was made, and the limit of six login/password combinations has been reached.
Operation and Maintenance 6-10 9783-A2-GB20-00 July 2000 T able 6-5. Device Messages (4 of 5) Message What T o Do What It Indicates No more DLCIs allowed N ew or C opyFrom was selected from an interface’s DLCI Records configuration screen, and the maximum number of DLCI Records had already been reached.
Operation and Maintenance 6-1 1 9783-A2-GB20-00 July 2000 T able 6-5. Device Messages (5 of 5) Message What T o Do What It Indicates Resetting Device, Please W ait ... Y es (or y) was entered in the Reset COM Port usage field of the System Paused menu.
Operation and Maintenance 6-12 9783-A2-GB20-00 July 2000 Status Information Status information is useful when monitoring the FrameSaver unit. The following illustration shows the Status menu for the FrameSaver DSL unit.
Operation and Maintenance 6-13 9783-A2-GB20-00 July 2000 System and T est Status Messages System and test status information is selected from the Status menu.
Operation and Maintenance 6-14 9783-A2-GB20-00 July 2000 Health and Status Messages The following table provides Health and Status messages that apply to the FrameSaver DSL unit. T able 6-7. Health and Status Messages (1 of 3) Message What It Indicates AIS at Network 1 An Alarm Indication Signal (AIS) is received by the network interface.
Operation and Maintenance 6-15 9783-A2-GB20-00 July 2000 T able 6-7. Health and Status Messages (2 of 3) Message What It Indicates Ethernet Link Down The Ethernet port is enabled, but communication between the management system and the unit is not currently possible on the port.
Operation and Maintenance 6-16 9783-A2-GB20-00 July 2000 T able 6-7. Health and Status Messages (3 of 3) Message What It Indicates SL V T imeout, DLCI nnnn , frame relay link 1, 2, 3 An excessive numb.
Operation and Maintenance 6-17 9783-A2-GB20-00 July 2000 T est Status Messages These test messages appear in the right column of the System and T est Status screen. Y ou have the option of allowing the test to continue or aborting the test. See Chapter 8, T roubleshooting , for more information on tests, including how to start and stop them.
Operation and Maintenance 6-18 9783-A2-GB20-00 July 2000 T able 6-8. T est Status Messages (2 of 2) Message What It Indicates Send Pttn Active, DLCI nnnn , frame_relay_link 1, 2 The unit is monitoring the selected test pattern on the specified DLCI for the interface.
Operation and Maintenance 6-19 9783-A2-GB20-00 July 2000 PVC Connection Status PVC connection statuses are selected from the Status menu. Main Menu → Status → PVC Connection Status Only PVC connections with Source DLCIs configured to be Active are shown.
Operation and Maintenance 6-20 9783-A2-GB20-00 July 2000 T able 6-9. PVC Connection Status (2 of 2) Field What It Indicates Status EDLCI 0 to 62 For multiplexed DLCIs only .
Operation and Maintenance 6-21 9783-A2-GB20-00 July 2000 Network Interface Status Network Interface Status can be viewed from the Status menu. Main Menu → Status → Network Interface Status Network.
Operation and Maintenance 6-22 9783-A2-GB20-00 July 2000 IP Routing T able Use the IP Routing T able to see all the routes configured in the FrameSaver unit.
Operation and Maintenance 6-23 9783-A2-GB20-00 July 2000 T able 6-1 1. IP Routing T able V alues Column What It Indicates Destination The Destination IP Address for the route: 001.000.000.000 – 223.255.255.255 Mask The Destination Subnet Mask for the route: H 000.
Operation and Maintenance 6-24 9783-A2-GB20-00 July 2000 Performance Statistics Use the Performance Statistics menu to display statistical information for a selected interface. Statistical information is useful when trying to determine the severity and frequency or duration of a condition.
Operation and Maintenance 6-25 9783-A2-GB20-00 July 2000 Clearing Performance Statistics Performance statistics counters can be reset to the baseline when using a directly-connected asynchronous terminal and your security Access Level is Level-1. This feature is useful when troubleshooting problems.
Operation and Maintenance 6-26 9783-A2-GB20-00 July 2000 Service Level V erification Performance Statistics These statistics appear when Service Level V erification (SL V) is selected from the Performance Statistics menu.
Operation and Maintenance 6-27 9783-A2-GB20-00 July 2000 T able 6-12. Service Level V erification Performance Statistics (2 of 2) Statistic What It Indicates H Above EIR * H The number of frames transmitted by the far-end device that were above the excess information rate and were dropped in transit.
Operation and Maintenance 6-28 9783-A2-GB20-00 July 2000 The statistics collected by the unit depend upon the device at the far end of the connection. If the far-end device is a FrameSaver SL V unit, frame relay , latency , and FDR/DDR (Frame Relay Delivery Ratio/Data Delivery Ratio) performance statistics are collected.
Operation and Maintenance 6-29 9783-A2-GB20-00 July 2000 T able 6-13. DLCI Performance Statistics (2 of 2) Statistic What It Indicates H With BECN Set H The number of frames and octets sent on the selected DLCI of the frame relay link with backward explicit congestion notifications.
Operation and Maintenance 6-30 9783-A2-GB20-00 July 2000 Frame Relay Performance Statistics The following statistics appear when Frame Relay is selected from the Performance Statistics menu.
Operation and Maintenance 6-31 9783-A2-GB20-00 July 2000 T able 6-14. Frame Relay Performance Statistics (2 of 2) Statistic What It Indicates Frame Relay Errors (cont’d) Unknown Error The number of frames received over the interface that do not fall into one of the other statistic categories.
Operation and Maintenance 6-32 9783-A2-GB20-00 July 2000 A TM Performance Statistics The following statistics appear when Frame Relay is selected from the Performance Statistics menu. Main Menu → Status → Performance Statistics → AT M All counts continue to increment until the maximum value is reached (2 32 –2), then the count starts over .
Operation and Maintenance 6-33 9783-A2-GB20-00 July 2000 T able 6-15. A TM Performance Statistics (2 of 2) Statistic What It Indicates OCD Events The number of times Out of Cell Delineation (OCD) events have been detected. An OCD event is declared when 7 consecutive cells with HEC violations are detected.
Operation and Maintenance 6-34 9783-A2-GB20-00 July 2000 Ethernet Performance Statistics The following statistics appear when Ethernet is selected from the Performance Statistics menu. Main Menu → Status → Performance Statistics → Ethernet Statistic What It Indicates Port Rate (Mbps) The operating rate as detected on the Ethernet port.
Operation and Maintenance 6-35 9783-A2-GB20-00 July 2000 T rap Event Log The T rap Event Log displays all traps stored in the SNMP trap event log. The following log example describes the alarm conditions that will generate an SNMP trap for a physical interface, and for the frame relay LMIs and DLCIs.
Operation and Maintenance 6-36 9783-A2-GB20-00 July 2000.
7-1 9783-A2-GB20-00 July 2000 FTP Operation 7 This chapter includes the following information: H FTP File T ransfers — Upgrading System Software — Determining Whether a Download is Completed — C.
FTP Operation 7-2 9783-A2-GB20-00 July 2000 FTP File T ransfers The FrameSaver unit supports a standard File T ransfer Protocol (FTP) server over T ransmission Control Protocol (TCP). A complete binary image of the configuration files can be copied to a host to provide a backup.
FTP Operation 7-3 9783-A2-GB20-00 July 2000 " Procedur e T o initiate an FTP session: 1. Start the FTP client program on your host. For example, on a UNIX host, type ftp , followed by the FrameSaver unit’s IP address.
FTP Operation 7-4 9783-A2-GB20-00 July 2000 Upgrading System Software If you need to upgrade the FrameSaver unit’s program code, you must transfer the upgrade of the nam.
FTP Operation 7-5 9783-A2-GB20-00 July 2000 Determining Whether a Download Is Completed T o see whether a download has completed, check the Identity screen. Main Menu → Status → Identity Check Alternate Software Rev . under the NAM Identity column.
FTP Operation 7-6 9783-A2-GB20-00 July 2000 T ransferring Collected Data SL V user history statistics and LMI packet capture data can be uploaded to an NMS or a Network Associates Sniffer using FTP , which is faster than other methods.
8-1 9783-A2-GB20-00 July 2000 T roubleshooting 8 This chapter includes the following: H Problem Indicators H Resetting the Unit and Restoring Communication — Resetting the Unit from the Control Menu.
T roubleshooting 8-2 9783-A2-GB20-00 July 2000 H DTE Loopback H IP Ping T est H Lamp T est Pr oblem Indicators The unit provides a number of indicators to alert you to possible problems: Indicators . . . See . . . LEDs Viewing LEDs and Control Leads and LED Descriptions in Chapter 6, Operation and Maintenance , as well as the user interface screen.
T roubleshooting 8-3 9783-A2-GB20-00 July 2000 Resetting the Unit and Restoring Communication Y ou can reset the unit in one of four ways: H Reset it from the Control menu. H Cycle the power . H Reset the configuration options for the COM port, or reload the factory default settings.
T roubleshooting 8-4 9783-A2-GB20-00 July 2000 Restoring Communication with an Improperly Configur ed Unit Improperly configuring the unit could render the menu-driven user interface inaccessible. If this occurs, connectivity to the unit can be restored via a directly connected asynchronous terminal.
T roubleshooting 8-5 9783-A2-GB20-00 July 2000 T roubleshooting Management Link Featur e A dedicated troubleshooting management link is available to help service providers isolate device problems within their networks.
T roubleshooting 8-6 9783-A2-GB20-00 July 2000 V iewing Captured Packets fr om the Menu-Driven User Interface The twelve most recent LMI events are stored in the trace log. Once the capture buffer or trace log is full, the oldest packets are overwritten.
T roubleshooting 8-7 9783-A2-GB20-00 July 2000 Alarms The following table describes the alarm conditions that will generate an SNMP trap for a physical interface, and the frame relay LMIs and DLCIs. These alarm conditions also generate Health and Status messages seen on the System and T est Status screen.
T roubleshooting 8-8 9783-A2-GB20-00 July 2000 T able 8-1. Alarm Conditions (2 of 4) Alarm Condition What T o Do What It Indicates LMI Down, frame relay link 2 The Local Management Interface is down for the specified frame relay link.
T roubleshooting 8-9 9783-A2-GB20-00 July 2000 T able 8-1. Alarm Conditions (3 of 4) Alarm Condition What T o Do What It Indicates Loss of Cell Delineation, atm link The A TM T ransmission Convergence.
T roubleshooting 8-10 9783-A2-GB20-00 July 2000 T able 8-1. Alarm Conditions (4 of 4) Alarm Condition What T o Do What It Indicates SNR Margin Threshold Exceed, Network 1 The user-specified SNR margin threshold has been exceeded. Contact your network provider .
T roubleshooting 8-1 1 9783-A2-GB20-00 July 2000 T rap Event Log The T rap Event Log displays all traps stored in the SNMP trap event log. The following log example describes the alarm conditions that will generate an SNMP trap for a physical interface, and for the frame relay LMIs and DLCIs.
T roubleshooting 8-12 9783-A2-GB20-00 July 2000 T able 8-2. Device Problems (2 of 2) Symptom Solutions Possible Cause Cannot access the unit or the menu-driven user interface. Login or password is incorrect, COM port is improperly configured, or the unit is otherwise configured so it prevents access.
T roubleshooting 8-13 9783-A2-GB20-00 July 2000 A TM Problems T able 8-3. A TM Problems Symptom Possible Cause Solutions OCD events; loss of cell delineation. Line impairments. Check Hotwire GranDSLAM statistics. Reduce the link rate. A TM statistics show VCs receiving no data.
T roubleshooting 8-14 9783-A2-GB20-00 July 2000 Frame Relay PVC Problems T able 8-4. Frame Relay PVC Problems Symptom Possible Cause Solutions No receipt or transmission of data Cross Connection of the DLCIs are configured incorrectly . V erify the PVC connections and DLCIs by checking the network-discovered DLCIs on the LMI Reported DLCIs screen.
T roubleshooting 8-15 9783-A2-GB20-00 July 2000 T ests A vailable The following tests are available to a FrameSaver DSL unit. T est Menu Example main/test 9783 Device Name: Node A 05/13/2000 08:02 TES.
T roubleshooting 8-16 9783-A2-GB20-00 July 2000 T est Timeout Feature A T est Timeout feature is available to automatically terminate a test (as opposed to manually terminating a test) after it has been running a specified period of time.
T roubleshooting 8-17 9783-A2-GB20-00 July 2000 " Procedur e T o start and stop a loopback or a set-pattern test: 1. Follow this menu selection sequence: Main Menu → T est 2. Select an interface and test (e.g., Network or Data Port PVC T ests) and press Enter .
T roubleshooting 8-18 9783-A2-GB20-00 July 2000 PVC T ests PVC tests can be run on a requested DLCI for a selected interface. The FrameSaver unit must be operating in frame relay mode. H When PVC tests are on a multiplexed DLCI between FrameSaver devices, they are nondisruptive to data, so user data can continue to be sent during a test.
T roubleshooting 8-19 9783-A2-GB20-00 July 2000 PVC Loopback The PVC Loopback loops frames back to the selected interface on a per-PVC basis. This test logically (not physically) loops back frames received from another FrameSaver device through the selected frame relay PVC to the same device.
T roubleshooting 8-20 9783-A2-GB20-00 July 2000 Monitor Pattern This test monitors packets filled with a hexadecimal 55 test pattern and sequence number over the selected interface and DLCI to another FrameSaver device.
T roubleshooting 8-21 9783-A2-GB20-00 July 2000 DTE Loopback The local DTE external Loopback (DTLB) test loops the received signal on the DTE interface back to the DTE without affecting the operation of the remaining ports. Use this test to isolate problems on the user data port.
T roubleshooting 8-22 9783-A2-GB20-00 July 2000 IP Ping T est An IP Ping test can be run to test connectivity between the FrameSaver unit and any FrameSaver unit, router , or NMS to which it has a route. In addition, the test can be run to access a remote unit for configuration purposes.
T roubleshooting 8-23 9783-A2-GB20-00 July 2000 " Procedur e 2 T o ping the NMS at the central site: 1. V erify that the central site NMS has the FrameSaver unit’ s IP address in its routing table so it can communicate with the FrameSaver unit.
T roubleshooting 8-24 9783-A2-GB20-00 July 2000 Lamp T est The FrameSaver unit supports a Lamp T est to verify that all LEDs are lighting and functioning properly . All LEDs flash or blink on and of f at the same time every 1/2 second during execution of the test.
9-1 9783-A2-GB20-00 July 2000 Setting Up OpenLane for FrameSaver Devices 9 This chapter includes: H OpenLane Support of FrameSaver Devices H Setting Up the OpenLane SLM System H Setting Up FrameSaver .
Setting Up OpenLane for FrameSaver Devices 9-2 9783-A2-GB20-00 July 2000 H Device reset capability H HP OpenV iew adapters for integrating OpenLane with the OpenV iew Web interface The advanced SL V f.
Setting Up OpenLane for FrameSaver Devices 9-3 9783-A2-GB20-00 July 2000 Setting Up FrameSaver and SL V Support With the OpenLane SLM system’s extensive online Help system, the application is self-documenting and you have access to the most current system information.
Setting Up OpenLane for FrameSaver Devices 9-4 9783-A2-GB20-00 July 2000 This page intentionally left blank..
10-1 9783-A2-GB20-00 July 2000 Setting Up Network Health for FrameSaver Devices 10 FrameSaver units are compatible with Concord Communication’s Network Health software.
Setting Up Network Health for FrameSaver Devices 10-2 9783-A2-GB20-00 July 2000 For additional information about installing, accessing, and managing FrameSaver DSL devices through Concord’s Network Health, and for information about applicable reports, refer to: H Network Health Installation Guide to help you install the application.
Setting Up Network Health for FrameSaver Devices 10-3 9783-A2-GB20-00 July 2000 Discovering FrameSaver Elements Once licenses are entered and you have access to the applications, the Discover dialog box opens. Use this dialog box to search for FrameSaver units in your network and discover their DLCIs.
Setting Up Network Health for FrameSaver Devices 10-4 9783-A2-GB20-00 July 2000 Configuring the Discover ed Elements Network Health sets the speed for discovered elements when it polls the unit for the first time. For a FrameSaver DSL unit, the speed set would be the unit’s CIR.
Setting Up Network Health for FrameSaver Devices 10-5 9783-A2-GB20-00 July 2000 Gr ouping Elements for Reports Once the discovery process is completed and required changes are made, the newly discovered elements (DLCIs) should be organized into a group for Health reporting.
Setting Up Network Health for FrameSaver Devices 10-6 9783-A2-GB20-00 July 2000 Generating Reports for a Gr oup Once Network Health has had sufficient time to gather data from the polled DLCIs and the DLCIs have been grouped, you can start generating reports.
Setting Up Network Health for FrameSaver Devices 10-7 9783-A2-GB20-00 July 2000 About T rend Reports By specifying specific variables like bandwidth, trend analysis can be performed and shown on T rend Reports. Up to ten variables for a DLCI, or ten DLCIs on one variable can be generated on a single trend report.
Setting Up Network Health for FrameSaver Devices 10-8 9783-A2-GB20-00 July 2000 — Elements Summary Report – Compares DLCI traffic with volume and the baseline, bandwidth utilization, and errors.
Setting Up Network Health for FrameSaver Devices 10-9 9783-A2-GB20-00 July 2000 — FrameSaver SL V Plus At-a-Glance Report – For FrameSaver units with the SL V and SLM reporting feature set, performs trend analysis on up to ten specified variables for DLCIs.
Setting Up Network Health for FrameSaver Devices 10-10 9783-A2-GB20-00 July 2000 H T rend Reports – Perform trend analysis on up to ten specified variables for DLCIs.
A-1 9783-A2-GB20-00 July 2000 Menu Hierar chy A Menus The following menus are a graphical representation of the FrameSaver DSL unit’s menu organization.
Menu Hierarchy A-2 9783-A2-GB20-00 July 2000 00-16771a Menu Hierar chy – Frame Rela y Mode Status System and T est Status PVC Connection Status Network Interface Status IP Routing T ab le P erforman.
Menu Hierarchy A-3 9783-A2-GB20-00 July 2000 00-16771b MAIN MENU Status T est Configuration Control Easy Install System Information • Device Name • System Name, Location, Contact • Date • Time.
Menu Hierarchy A-4 9783-A2-GB20-00 July 2000 This page intentionally left blank..
B-1 9783-A2-GB20-00 July 2000 SNMP MIBs and T raps, and RMON Alarm Defaults B This appendix contains the following: H MIB Support H Downloading MIBs and SNMP T raps H System Group (mib-2) — FrameSav.
SNMP MIBs and T raps, and RMON Alarm Defaults B-2 9783-A2-GB20-00 July 2000 MIB Support The FrameSaver unit supports the SNMP V ersion 1, and has the capability of being managed by any industry-standard SNMP manager and accessed by external SNMP managers using the SNMP protocol.
SNMP MIBs and T raps, and RMON Alarm Defaults B-3 9783-A2-GB20-00 July 2000 System Gr oup (mib-2) This section provides the system description and system object identifier for the System Group for the FrameSaver DSL unit, which is an SNMPv1 MIB.
SNMP MIBs and T raps, and RMON Alarm Defaults B-4 9783-A2-GB20-00 July 2000 Interfaces Gr oup (mib-2) Clarification for objects in the Interfaces Group, as defined in RFC 1573 and RFC 1213, which is an SNMPv1 MIB, is provided in this section.
SNMP MIBs and T raps, and RMON Alarm Defaults B-5 9783-A2-GB20-00 July 2000 NetScout Indexes to the Interface T able (ifT able) For remote monitoring at sites where FrameSaver units are operating with NetScout Probes, use the following ifName, ifDescr , and ifIndex.
SNMP MIBs and T raps, and RMON Alarm Defaults B-6 9783-A2-GB20-00 July 2000 Standards Compliance for SNMP T raps This section describes the FrameSaver unit’s compliance with SNMP format standards and with its special operational trap features. All traps have an associated string to help you decipher the meaning of the trap.
SNMP MIBs and T raps, and RMON Alarm Defaults B-7 9783-A2-GB20-00 July 2000 T rap: warmStart This trap indicates that the FrameSaver unit has been reset and has stabilized. T able B-3. warmStart T rap T rap What It Indicates Possible Cause warmStart FrameSaver unit has just reinitialized and stabilized itself.
SNMP MIBs and T raps, and RMON Alarm Defaults B-8 9783-A2-GB20-00 July 2000 T raps: linkUp and linkDown These traps are supported on the following interfaces: H Physical sublayer interfaces: network, Ethernet, and synchronous data ports H Frame relay logical link layer interfaces T able B-5.
SNMP MIBs and T raps, and RMON Alarm Defaults B-9 9783-A2-GB20-00 July 2000 T able B-6. linkUp and linkDown V ariable-Bindings (1 of 3) Interface V ariable-Bindings Possible Cause Physical Sublayer Network (Supported by an entry in the MIB-II interfaces table.
SNMP MIBs and T raps, and RMON Alarm Defaults B-10 9783-A2-GB20-00 July 2000 T able B-6. linkUp and linkDown V ariable-Bindings (2 of 3) Interface Possible Cause V ariable-Bindings Physical Sublayer (cont’d) Ethernet Port H ifIndex (RFC 1573) H ifAdminStatus (RFC 1573) H ifOperStatus (RFC 1573) H devLastT rapString (devHealthAndStatus.
SNMP MIBs and T raps, and RMON Alarm Defaults B-1 1 9783-A2-GB20-00 July 2000 T able B-6. linkUp and linkDown V ariable-Bindings (3 of 3) Interface Possible Cause V ariable-Bindings A TM Logical Link Sublayer Network (Supported by an entry in the MIB-II interfaces table.
SNMP MIBs and T raps, and RMON Alarm Defaults B-12 9783-A2-GB20-00 July 2000 T raps: enterprise-Specific These traps indicate that an enterprise-specific event has occurred.
SNMP MIBs and T raps, and RMON Alarm Defaults B-13 9783-A2-GB20-00 July 2000 T able B-7. enterprise-Specific T raps and V ariable-Bindings (2 of 3) T rap Possible Cause V ariable-Bindings enterpriseMissedSL V - Down(16) H devFrExtDlciIfIndex (devFrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-14 9783-A2-GB20-00 July 2000 T able B-7. enterprise-Specific T raps and V ariable-Bindings (3 of 3) T rap Possible Cause V ariable-Bindings enterpriseT est- Start(5) For physical interfaces and frame relay links: H ifIndex (RFC 1573) H .
SNMP MIBs and T raps, and RMON Alarm Defaults B-15 9783-A2-GB20-00 July 2000 T raps: RMON-Specific T wo traps are defined to support the Alarm and Events Groups of RMON. See RMON Alarm and Event Defaults for the default values that will generate RMON-specific traps.
SNMP MIBs and T raps, and RMON Alarm Defaults B-16 9783-A2-GB20-00 July 2000 RMON Alarm and Event Defaults The FrameSaver unit supports automatic generation of RMON alarm and event information. Each alarm sets an SNMP variable to monitor . When the threshold set for the monitored variable is exceeded, an SNMP trap or a log event is sent.
SNMP MIBs and T raps, and RMON Alarm Defaults B-17 9783-A2-GB20-00 July 2000 Physical Interface Alarm Defaults This alarm only applies to the FrameSaver DSL unit’s network interface.
SNMP MIBs and T raps, and RMON Alarm Defaults B-18 9783-A2-GB20-00 July 2000 Frame Relay Link Alarm Defaults These alarms apply to the FrameSaver unit’s frame relay link interfaces.
SNMP MIBs and T raps, and RMON Alarm Defaults B-19 9783-A2-GB20-00 July 2000 T able B-10. Frame Relay Link Alarm Defaults (2 of 2) Item Falling Threshold Default Rising Threshold Default Event T ype Interval MIB/T ag/OID 2 Sample T ype 1 Tx T otal Errors D MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-20 9783-A2-GB20-00 July 2000 DLCI Alarm Defaults – Paradyne Area These alarms apply to all DLCIs on the network interface and can be created during RMON initialization or when a DLCI is created. They are put into the Paradyne alarm area.
SNMP MIBs and T raps, and RMON Alarm Defaults B-21 9783-A2-GB20-00 July 2000 T able B-1 1. DLCI Alarm Defaults – Paradyne Area (2 of 3) Item Falling Threshold Default Rising Threshold Default Event T ype Interval MIB/T ag/OID 2 Sample T ype 1 Frames Sent D MIB: FR DTE MIB (RFC 21 15) T ag: frCircuitSentFrames OID: .
SNMP MIBs and T raps, and RMON Alarm Defaults B-22 9783-A2-GB20-00 July 2000 T able B-1 1. DLCI Alarm Defaults – Paradyne Area (3 of 3) Item Falling Threshold Default Rising Threshold Default Event T ype Interval MIB/T ag/OID 2 Sample T ype 1 Tx Frames Exceeding CIR D MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-23 9783-A2-GB20-00 July 2000 Object ID Cr oss-References (Numeric Order) The FrameSaver unit supports automatic generation of RMON alarm and event information. Each alarm sets an SNMP variable to monitor .
SNMP MIBs and T raps, and RMON Alarm Defaults B-24 9783-A2-GB20-00 July 2000 T able B-14. History OID Cr oss-Reference (1 of 5) Object ID (OID) 1 Item MIB/T ag .1.3.6.1.2.1.2.2.1. . . .1.3.6.1.2.1.2.2.1. 5.I Link Speed MIB: MIB II (RFC 1573) T ag: ifSpeed .
SNMP MIBs and T raps, and RMON Alarm Defaults B-25 9783-A2-GB20-00 July 2000 T able B-14. History OID Cr oss-Reference (2 of 5) Object ID (OID) 1 MIB/T ag Item .1.3.6.1.4.1.1795.2.24.2.6.9.4. . . .1.3.6.1.4.1.1795.2.24.2.6.9. 4 .1.1 . 3.I . D DLCI CIR MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-26 9783-A2-GB20-00 July 2000 T able B-14. History OID Cr oss-Reference (3 of 5) Object ID (OID) 1 MIB/T ag Item .1.3.6.1.4.1.1795.2.24.2.6.9.4 . . . .1.3.6.1.4.1.1795.2.24.2.6.9.4. 1.1.57.I . D Network Frames Dropped Above CIR Within EIR MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-27 9783-A2-GB20-00 July 2000 T able B-14. History OID Cr oss-Reference (4 of 5) Object ID (OID) 1 MIB/T ag Item .1.3.6.1.4.1.1795.2.24.2.6.9.4.5.2.1. . . .1.3.6.1.4.1.1795.2.24.2.6.9.4.5.2.1 .2 . I.D.N Burst Upper Limit (1– 5) MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-28 9783-A2-GB20-00 July 2000 T able B-14. History OID Cr oss-Reference (5 of 5) Object ID (OID) 1 MIB/T ag Item .1.3.6.1.4.1.1795.2.24.2.6.9.4.10.3.1. . . .1.3.6.1.4.1.1795.2.24.2.6.9.4.10.3.1 .2 . I.N Port Burst Upper Limits 1– 4 MIB: pdn_FrExt.
SNMP MIBs and T raps, and RMON Alarm Defaults B-29 9783-A2-GB20-00 July 2000 T able B-15. Alarm OID Cr oss-Reference (1 of 2) Object ID (OID) Item MIB/T ag .1.3.6.1.2.1.10.32.2.1. . . .1.3.6.1.2.1.10.32.2.1. 4.I . D Rx FECNs MIB: FR DTE MIB (RFC 21 15) T ag: frCircuitReceivedFECNs .
SNMP MIBs and T raps, and RMON Alarm Defaults B-30 9783-A2-GB20-00 July 2000 T able B-15. Alarm OID Cr oss-Reference (2 of 2) Object ID (OID) MIB/T ag Item .1.3.6.1.4.1.1795.2.24.2.6.9.4. . . .1.3.6.1.4.1.1795.2.24.2.6.9.4. 3.1.7.I . D Current Latency MIB: pdn_FrExt.
C-1 9783-A2-GB20-00 July 2000 Connectors, Cables, and Pin Assignments C This appendix shows the FrameSaver unit’s rear panel, and the pin assignments for the connectors/interfaces and cables. Rear Panel The following illustration shows the FrameSaver DSL unit’s rear panel.
Connectors, Cables, and Pin Assignments C-2 9783-A2-GB20-00 July 2000 DSL Network Interface Cable The DSL network interface connector is an RJ48C 8-position keyed modular jack.
Connectors, Cables, and Pin Assignments C-3 9783-A2-GB20-00 July 2000 COM Port Connector The following table provides the pin assignments for the FrameSaver unit’s 25-position EIA-232C communication port connector .
Connectors, Cables, and Pin Assignments C-4 9783-A2-GB20-00 July 2000 Standard EIA-232-D Crossover Cable A standard crossover cable can be used to connect the COM port to an external modem. The external modem must be configured so it is compatible with the FrameSaver unit.
Connectors, Cables, and Pin Assignments C-5 9783-A2-GB20-00 July 2000 " Procedur e T o configure an external modem: 1. Disconnect the asynchronous terminal from the standard cable. See page C-4 for an illustration of the COM Port connection . 2. Reconnect the crossover cable to the external modem.
Connectors, Cables, and Pin Assignments C-6 9783-A2-GB20-00 July 2000 Data Port Connector The following table provides the pin assignments for the 34-position V .
Connectors, Cables, and Pin Assignments C-7 9783-A2-GB20-00 July 2000 Ethernet Port Connector The following table provides the pin assignments for the FrameSaver unit’s 8-position RJ45 Ethernet port unkeyed modular jack.
Connectors, Cables, and Pin Assignments C-8 9783-A2-GB20-00 July 2000 This page intentionally left blank..
D-1 9783-A2-GB20-00 July 2000 T echnical Specifications D T able D-1. FrameSaver DSL T echnical Specifications (1 of 2) Specification Criteria Approvals FCC Part 15 Safety Class A digital device Refer to the equipment’s label for safety information.
T echnical Specifications D-2 9783-A2-GB20-00 July 2000 T able D-1. FrameSaver DSL T echnical Specifications (2 of 2) Specification Criteria COM Port Standard Data rates 25-position (DB25) connector EIA-232, V .24 (ISO 21 10) 9.6, 14.4, 19.2, 28.8, 38.
E-1 9783-A2-GB20-00 July 2000 Equipment List E Equipment See page E-2 for cables you can order . Description Model / Feature Number FrameSaver DSL Units FrameSaver DSL unit with 8 PVCs and Basic Feature Set. Includes 1-Slot Housing, 120 V ac Power Supply , Network Cable, Installation Instructions, and Quick Reference.
Equipment List E-2 9783-A2-GB20-00 July 2000 Description Model / Feature Number NMS Products OpenLane Enterprise 7805-D1-001 OpenLane Workgroup 7805-D1-003 NetScout Manager Plus – For UNIX or Window.
IN-1 9783-A2-GB20-00 July 2000 Index Numbers 55 hexadecimal, test pattern, 8-19, 8-20 A aborting tests, 8-17 Access Dial-In, 4-46 Name, 4-31 T ype, 4-36 Access Level, 5-10, 5-1 1 assigning, 5-9 Port, .
Index IN-2 9783-A2-GB20-00 July 2000 Concord’s Network Health, 1-1 compatibility , 10-1 Configuration Auto, Active, 6-14 displaying and changing options, 3-4 FTP transfer rate, 1-8 menu, 3-2 menu/br.
Index IN-3 9783-A2-GB20-00 July 2000 DSL front panel LED, 6-5 network interface options, 4-13 Network Interface Status screen, 6-21 DTE Loopback, 8-21 port connector pin assignments, C-6 port-initiate.
Index IN-4 9783-A2-GB20-00 July 2000 H hardware revision, NAM, 6-2 HDLC errors, frame relay statistics, 6-31 Health and Status, 8-2 messages, 6-14 Hop, 6-23 hyperlink to more information, highlighted .
Index IN-5 9783-A2-GB20-00 July 2000 Login, 5-1 creating, 5-1 1 ID, 5-1 1 modifying and deleting, 5-12 Required, 4-33, 4-43, 5-3, 5-5, 5-6 LOL, linkDown trap, B-9 Loopback DTE, 8-21 Port (DTE) Initiat.
Index IN-6 9783-A2-GB20-00 July 2000 O odd parity , 4-42 OID, cross-reference (numeric order), B-24, B-29 OK, LED, 6-4, 6-5 OpenLane, 1-1 1 SLM support, 9-1 operation, 2-1 organization of this documen.
Index IN-7 9783-A2-GB20-00 July 2000 right arrow key , 2-6 RIP , 1-8, 4-6, 4-45 proprietary , 4-38 RJ45, Ethernet Port connector , C-7 RJ48C network cable, C-2 RMON alarm and event defaults, B-16 Spec.
Index IN-8 9783-A2-GB20-00 July 2000 statistics, 1-10, 6-24 elements, 10-3 uploading to an NMS, 7-6 Status Enquiry , LMI, 4-9 Health and, 6-14 information, 6-12 LED, 6-4 menu/branch, 2-4 network inter.
Index IN-9 9783-A2-GB20-00 July 2000 T rend, report, 10-7 troubleshooting, 8-1 creating a management link, 4-24 device problems, 8-1 1 frame relay PVC problems, 8-13, 8-14 management link, 8-5 tables,.
An important point after buying a device Paradyne 9783 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Paradyne 9783 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Paradyne 9783 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Paradyne 9783 you will learn all the available features of the product, as well as information on its operation. The information that you get Paradyne 9783 will certainly help you make a decision on the purchase.
If you already are a holder of Paradyne 9783, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Paradyne 9783.
However, one of the most important roles played by the user manual is to help in solving problems with Paradyne 9783. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Paradyne 9783 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
