Instruction/ maintenance manual of the product 950102 ParaBody
Go to page of 25
Serious Steel 950 ST 9501.02 ASSEMBLY INSTRUCTIONS Part # 6705001 P, zv~on: 08104197.
! ! ! ATTENTION ! ! ~ UNLE,:,S 0 THER WISE SHOWN, z~LL CONNECTIONS WILL CONSIST OF ONE 1~ ~o~ ~; two ~N~ ONF~ a),,gOC~N~r. BOLT ~ LOCKNUT NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE ~ .OF THE BOLT. ~/i////i~ BOLT LENGTH BOLT LENGTH RULER: 1/2 ] 1/2 .
950 ST Parts List KEY 2 3 4 5 6 7 ’9 ’11 12 13 14 15 ~6 17 18 19 2O 21 ~ 23 24 26 27 28 29 30 31 32 34 36 36 37 ’38 39 "40 41 42 43 ’45 46 47 48 "49 50 51 52 53 54 "55 56 57 58 "’69 PART.
Frame Assembly Instructions Use th~s procedure to assemble the frame of the ParaBady 950ST ~ .~t/8" X 4’ NUT X 3" I~rtLT ~ Step A. I Loosely assembler the leg we|~ht base (18) and the press weight stack base (1~, to 1’he base (15) using two 1/2 x 5-1/2 bolts (91), four 1/2" washers(79), and two 1/2’ nyl¢)ck nuts shown.
Step 2 ’ A. Securely assemble the f!,oatln~ p.ulle.y stop (3.2~, and the s.eaf, support (33). to the front ~,prlght (31) using two 1/2 x 4-,1/2 bolts (.gO), four 1/Z~ washers (~79), and two 1/2" nylock nuts (82). e. Securely assemble one 3/6" spring pin (62) to the seat support (33) as shown.
2-314".
)3/8 X 3" Step 4 A. urel attach the press ~ase (13) to the base (15) using ~wo IlZ x.3-~I/4" bolts (!19;~ tw~,.11z" the rear upright (~21) using one ;~/o bol~ wasne~ L{=~ ,~"= "7- "~o~ ~.~ --e 3/B nylocK nut (B3). (95), tWO 5/B washers L~o) .
Step 5 A. Securely attach the press frame (17) to the pr.e.ss base (13) us;ng one 3" bolts (95), "~wo 1/2" washers C79), fo.u.r 3/8, washers (78), one nylock nu~s (B3).
Step 6 A. SlTde two hinge tabs (73) onto the wolff sleeve (39) and securely attach press seat pl:ld (49) two 3/8 x 1" bolf;~ (97), and two 3/8" washers (78).
318 X LOV HEIGHT NUT HEIGHT NUT Step 7 A. Loosely attach the press arm odiu.sj (25) tp the rear up~!ght (21) using two 1" pillow block bearings (112), four 3/8 x 3-1/4: bolts ~9B), four 5/B washers ~TB~, and four 5/8" nylock nuts ~No~e: A~och pillow blocks ~112~ so the set screws ore on ~he inside, this w~ll ollow mote adjustment.
Step 8 A. Co 31/B X 3-1/4 ° ~ ,~~ (~1/2 X 3-114" Securely attach the re(=r leg base (10) and ihe leg curl handle (9) to the leg frame (14) using 1/2 x 3- " bolts (.
STEP 9-A STEP 9-B ~ STEP g A. Slide two hinge tabs; (73) onto the leg frame (14) and securely attach leg scat pad (4T) using 3/8 x I" bolls (97), and two 5/B" washers (TB). (Nole: The "hinge" part of the hinge tab should face downward.
STEP 11. A. Securely assemble two 3/8" spring pins (62) to the leg curl/extension (8) as shown. B. Apply eight 1-1/2 x 5/A-" glides (63) to the outside surfaces of each roller pad adiuster (34) shown, and insert roller pad adjusters (34) into the leg curl/extenslon (8).
I Step 12 A. Insert two plate bushings ~102~ |nto She °’ParaBody" side of each of sixty weight plates (677 as shown. B. Insert one guide rod (28~ through one weight stock cushion (109~ and into each of the large hales in the base C15), the leg welghf stock base ~IB~, and the press weight stack press (1~ as shown.
3Z8 x 3"(~ Step , 13 Slide pec guide roC[ support (43..~ onto the pec welght.stack guide rods and Ioosely,,att,,ch it bolts (95), four 5/8 washers (78), and two 3/8 nyiock to the boom using two nuts (83). (Note: This connection will be secured in a later step after the pulleys are assembled.
CABLE GUIDE PEC DEC% CABLE STAMPED 65356 -77 51B" PART NUMBER PRESS STAMPED 66274- PART NUMBER AB CRUN% ¯ CABLE /--- STAMPED PART NUMBER ./6707B .
Pec Dec Cable Assembly Instructions Use this procedure to assemble the pec dec cables of the ParaBody 950ST Step C Step F & H Step G I 1318 x ~-3/4.
Step 2 of the pec dec cable (104) |o the slotted bushing on |h~ ri.ght p.ec A. Connect o.ne..end .... ~ ^~ the ~ec dec cable around the front upright {,31.~ anc~ 29. Route the o~l~er e.u .y, . .~% ..... ;o ~e slotted bush, ng on tne ,e’T P== ..... " WO 4--1/2" pulleys (110) to the center B.
I I I I I I I / / / step A. Securely assemble ~!he threaded end of the ab crunch cable (105) approximately 3/4" into the end the pulley bracket (25) and tighten jam nut securely.
I I Step A. 4 Securely assemble the ball end of the ab .crunch cable (106).a,,nd one 3-1/2" pu. lley (’.111).t~,,,the front upright (51) using tw.o 3/6 x 2-3/4: bolts (gg), two 3/8’ flange spacers (74), washers (78), and two 3/8 nylock nuts (83).
Press Station Cable Assembly Instructions Use this procedure to assemble the press station cable of the ParaBody 950!~T Step 1 A. Secure the ball end of the press cable .
Ao Secure the press cable (105) and two 3-1~/2" pulleys (111) ~o the pu!ley flats on the press base (13) and ~ ress weight slack base (1) using two 3//8 x 2" bolts (78), and two 3/8" nylock nuts (83). (Note: The cable should be routed underneath the shaft leg of the ’L’ bracket.
STEP 1 A. 3/B X 2-3/4 ° Leg Station Cable Assembly Instructions Use this procedure to assemble the leg .station cable of the PARABOD¥ 950 S’T Route the "loop" end of the leg cable (lOB) into the rear sl,}t of the leg weight stack base (I"B) behind the welght stack, and out through the slot near the leg station.
STEP 2 A. Screw the threaded end of the leg cable 4108) approximately 3/4" into the end of the selector shaft (113) and tighten ]am nut securely as shown.
B. Securely assemble the. = press station shroud (53) the press guide rod support (2,,4) and the press weight stack bose (1) using fhre=. = 3/8 x .1 .bla.ck button head cap screws (59) and one .3/8 X 1" bolt (~97). (,Note: The press shroud has ~he press exercise diagram.
An important point after buying a device ParaBody 950102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 950102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 950102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 950102 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 950102 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 950102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 950102.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 950102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 950102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
