Instruction/ maintenance manual of the product 888101 ParaBody
Go to page of 11
888101 SNI][TH NIACH][NE ASSEMBLY ]INSTRUCTIONS Part # 6801501 1 Revision.: 2/10/99.
WELCOME TO THE WORLD OF ~,~i~u$ ~ee~ ~. Please note: * Thar~k you for purchasing the Parabody 888101 SMITEI MACHINE. Please read these in- structions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
1’" 6798103 ’2 679~103 3 67985O2 4 6798402 ~ 679~702 6 6798901 7 6799601 "8 ,. 6799203 9 6799801 ’10 6714901 11 32030o2[ PART LOWER CROSS BRACE SMrrl-IBk~ POD GLm)EROD BUSH]NO 1" SHAFF COLLAR 2 .
1/2X3"~ FIGURE 2 STEP 2: ¯ LOOSELY assemblethe PLATEHOLDEP--S (7) andtheLOWERCROSS SUPPORT (2) totheUPRIGIff-f FRAMES (8) as FIGURE 2 using four 1/2 X 3" BOLTS (13), and four 1/2" LOCK.
I I I FIGURE 3 STEP 3: ¯ Insert two 3 X 2" END CAP S (12) into the ends of the UPRIGHT FRAMES (8) as shown in FIGURE ¯ Insert four GUIDE ROD BUSHINGS (10) into the UPRIGHT FRAMES (8) as shown i.
FIGURE 4 STEP 4: ¯ Insert one 1-3/4" ROUND END CAP (20) into the end of each HOUSING (6) as shown in FIGURE ¯ Slide one 2-1/2" OD BUMPER (19) over the end of each HOUSING (6) as shown in F.
FIGURE 5 ;TEP 5: ¯ Hookthe SMITH BAR (5) intothe slots ofthe UPRIGHT FRAM]ES (8). ¯ CAREFULLY slide one GUIDE ROD (9) fltrough the upper hole in the UPRIGHT FRAME (8).
FIGURE 6 STEP 6: Attach six 3-1/4 X 1-3/4" OLI]3ES (18) to the LEFT & RIGHT SAFETY STOPS (3 & 4) as shown in FIGURE 6 using following steps: ¯ Thoroughly clean all surfaces where the 3-1/4 X 1-3/4" GLIDES (18) are to be attached.
FIGURE 7 STEP 7: ¯ .Assemble the LEFT & RIGHT SAFETY STOPS (3 & 4) to the UPRIGHT FRAMES (8) as shownin FIGURE.
FIGURE 8 STEP 8: ¯ Insert sixteen 9/16" CAP PLUGS (17) into the exposed holes inthe UPRIGHT FRAMES (8) as shownin FIGURE ¯ Insert eight 7/16" CAP PLUGS (16) into the exposed holes in the UPPER & LOWER CROSS BRACES (1 & 2) as sho~t in FIGURE Thank you for purchasing the Parabody 888101 SMITH MACHINE.
FIGURE 8 STEP 8: ¯ Insert sixteen 9/16" CAP PLUGS (17) into the exposed holes inthe UPRIGHT FRAMES (8) as shownin FIGURE ¯ Insert eight 7/16" CAP PLUGS (16) into the exposed holes in the UPPER & LOWER CROSS BRACES (1 & 2" as sho~a~ in FIGURE Thank you for purchasing the Parabody 888101 SMffH MACHINE.
An important point after buying a device ParaBody 888101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 888101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 888101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 888101 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 888101 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 888101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 888101.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 888101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 888101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
