Instruction/ maintenance manual of the product 887 ParaBody
Go to page of 16
1 887 LA T OPTION CLASS H PAR T # 7305601 REV . A Revision: 06/20/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 877 Lat Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
4 P AR TS LIST PA R T # LEA6800209 LEA6800610 LEA6800809 LEA6801009 LEA6801110 LEA6759810 LEA6274410 LEA6725310 LEA3116201 LEA3116101 LEA6802101 LEA6671601 LEA6692601 LEA3103102 LEA6140701 LEA6405201 .
5 FIGURE 2 STEP 2: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSEL Y assemble the PULLEY HOUSING (3) and the UPRIGHT (1) to the LOWER CROSS SUPPOR T using two 3/8 X 4” BOL TS (38), four 3/8” W ASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29).
6 STEP 3: FIGURE 3 • Insert two 2-1/2” ROUND END CAPS (19) into the ends of the ADJ. FOOT SUPPOR T (2) as shown in FIGURE 3. • Insert one 1-3/4” END CAP (20) into the end of the ADJ.
7 STEP 4: FIGURE 4 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach eight 1 X 1” GLIDES (15) to the ends the CARRIAGE (6) as shown in FIGURE 4 using the following steps: • Thoroughly clean all surfaces where the 1 X 1” GLIDES (15) are to be attached.
8 STEP 6: FIGURE 6 • LOOSEL Y assemble the TOP BOOM (4) to the UPPER CROSS SUPPOR T using two 3/8 X 4” BOL TS (38), four 3/8” W ASHERS (30) and two 3/8” LOCK NUTS (31).
9 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 8: FIGURE 8 • Route the 115-1/4” CABLE (11) through the TOP BOOM (4) as shown in FIGURE 8. • SECUREL Y assemble three 3-1/2” PULLEYS (9) into the sl.
STEP 9: FIGURE 9 10 31 • Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 9.
11 STEP 10: FIGURE 10 • Route the threaded end of the 121-3/4” CABLE (12) through the slot of the PULLEY HOUSING then SECUREL Y assemble one 4-1/2” PULLEY (10) to the PULLEY HOUSING (3) using two 3/8 X 2-3/4” BOL TS (32), two 3/8” FLANGE SP ACERS (33), two 3/8” W ASHERS (30), and two 3/8” LOCK NUTS (31).
12 STEP 1 1: FIGURE 1 1 • Loop the 121-3/4” CABLE (12) around one 3-1/2” PULLEY (9) as shown in FIGURE 11. • LOOSEL Y assemble the 3-1/2” PULLEY (9) to the 3/16 X 1-3/4 X 5-1/4” PLA TES (23) using one 3/8 X 2” BOL T (35), two 3/8” W ASHERS (30), and one 3/8” LOCK NUT (31).
13 STEP 12: FIGURE 12 Thank you for pur chasing the Parabody 887 LA T OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. • Attach the LA T BAR (8) to the ball end of the upper CABLE (1 1) using one 5/16” SNAP HOOK (34) as shown in FIGURE 12.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 14 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
15 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED W ARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life FitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
An important point after buying a device ParaBody 887 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 887 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 887 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 887 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 887 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 887, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 887.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 887. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 887 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
