Instruction/ maintenance manual of the product 100 ParaBody
Go to page of 11
100 LEG PRESS CLASS H P AR T# 7155801 REV . B V ersion: 100102 Revision: 09/26/01 1 ASSEMBL Y INSTRUCTIONS W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the Parabody 100102 LEG PRESS. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 P AR TS LIST PA RT # 7140508 7140802 6806208 7140608 7140708 7140908 7128108 6994721 3102922 KEY 1 2 3 4 5 6 7 8 9 QTY 1 1 1 1 1 1 1 2 6 PA R T # 3102501 3102802 3102944 3102801 3104901 6416601 71 1.
9-1 /2" 4 FIGURE 1 STEP 1: • SECUREL Y assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOL T (12), two 3/4” FLANGE BEARINGS (14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13).
11-1/4" 5 FIGURE 2 STEP 2: • SECUREL Y assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOL T (12), two 3/4” FLANGE BEARINGS (14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13).
FIGURE 3 STEP 3: 6 • Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the SECOND ARM (5) as shown in FIGURE 3. • Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the MAIN ARM (4) as shown in FIGURE 3.
7 STEP 4: FIGURE 4 • SECUREL Y assemble the FOOTPLA TE (6) to the SECOND ARM (5) and the MAIN ARM (4) using two 1/2 X 5” BOL TS (12) and two 1/2” LOCK NUTS (13).
8 STEP 5: FIGURE 5 3/8 X 2-3/4” 9 1 11 10 3 • SECUREL Y assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 2-3/4” BOL TS (9), four 3/8” FLA T W ASHERS (10) and two 3/8” LOCK NUTS (1 1) as shown in FIGURE 5.
9 STEP 6: FIGURE 6 • CAREFULLEY slide the SEA T ADJUST (2) into the FRAME (1) and engage the SPRING PIN into one of the adjustment holes. See FIGURE 6. • Attach eight P ARAGLIDE STRIPS (15) to the inside of the tube on the FRAME (1) using the following steps: • Thoroughly clean all surfaces where the P ARAGLIDE STRIPS (15) are to be attached.
STEP 7: FIGURE 7 • SECUREL Y assemble one P AD (8) to the SEA T ADJUST (2) using two 3/8 X 2-3/4” BOL TS (9) and two 3/8” FLA T W ASHERS (10) as shown in FIGURE 7.
11 STEP 8: FIGURE 8 • SECUREL Y assemble one P AD (8) to the FRAME (1) using two 3/8 X 2-3/4” BOL TS (9) and two 3/8” FLA T W ASHERS (10) as shown in FIGURE 8.
An important point after buying a device ParaBody 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 100 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 100 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 100.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
