Instruction/ maintenance manual of the product KX-P8415 Panasonic
Go to page of 32
Setup Guide Model No. KX-P8415 Color Laser Printer and Reference Guide Setup Guide . . . . . . . . . . . . . . .3 Before Y ou Start Setup Reference Guide . . . . . . . . . . .17 Loading Media Settings and Printing Maintenance Appendix This manual includes Setup Guide and Reference Guide.
2 End-User License Agreement THIS IS A LEGAL AGREEMENT BETWEEN YOU AND PANASONIC. CAREFULLY READ ALL THE TERMS AND CONDITIONS OF THIS AGREEMENT PRIOR TO OPENING THE PACKET OF SOFTWARE PROGRAM. OPENING THE PACKET INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS.
End-User License Agreement . . . . .2 For Y our Safety . . . . . . . . . . . . . . . . .4 Cautions . . . . . . . . . . . . . . . . . . . . . . .7 System Requirements . . . . . . . . . . .8 Minimum Space Requirements . . . .8 Power Source . . . . . . .
Caution This printer utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. W arning Make sure that the printer is installed in a well ventilated room so as not to increase density of ozone in the air.
5 CAUTION: HOT SURFACE INSIDE ATTENTION: SURFACE CHAUDE CI-INTERIEUR VORSICHT: HEISSE FLÄCHE INTERN ATENCION: SUPERFICIE CALIENTE EN EL INTERNO CAUTION: HOT SURFACE INSIDE CAUTION: HOT SURFACE BELOW .
6 FOR USERS IN AUSTRALIA This mark shows that the product complies with AS/NZS 3548. FOR USERS IN U.K. IMPORTANT: FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This printer is supplied with a moulded three pin mains plug each for your safety and convenience.
7 To avoid machine malfunction, do not use the equipment under the following conditions: B Liquids near the equipment B Unstable or unlevel surfaces B Directly in front of air conditioning vents Cautions B Direct exposure to sunlight B Extremely high or low temperature [temperature range: 10˚C to 32.
8 Based on the IEEE P1284-B standard (An ECP compatible parallel port is recommended for Windows 95 and Windows 98. To turn on the ECP mode, use the computer’s BIOS setup.
9 Make sure that all accessories shown below were provided and have not been damaged. Report damage or shortages to the reseller from which the units were purchased. Page 3 includes an area for recording important information such as the name of reseller, serial number, and date of purchase.
10 # Open the front door . $ T urn the upper green lever clockwise until it stops and the arrows are aligned. (This tightens the internal belts to ready the unit for printing.) Close the front door . Remove the adhesive tape and lower the output tray .
11 If you do not have a parallel interface cable, you will need to purchase one (see below) from your local computer store or dealer. For detailed information, see page 31 in the Reference Guide. Make sure the computer , printer and the other connected peripheral devices are turned off.
12 Push down on the metal plate until it clicks, locking it in place. Fan the paper , then tap it on a level surface to avoid media jams or skewed printing. Notes: B Be careful not to leave fingerprints on the media, which can result in a smudged print.
13 When installing the KX-P8415 software, the following can be installed. - KX-P8415 printer driver - KX-P8415 Operating Instructions and this manual - Acrobat Reader * 1 To open and read the KX-P8415 Operating Instructions manual on your screen, Acrobat Reader program is needed.
14 The KX-P8415 CD-ROM includes the files for Setup Guide and Reference Guide, Operating Instructions , and the Acrobat Reader . Setup Guide and Reference Guide, and Operating Instructions are automatically installed on your computer when installing the KX-P8415 software.
15 If you need to remove the KX-P8415 software, perform the following steps. Click Start , move the pointer to Programs , Panasonic and Panasonic KX-P8415 . Click Uninstall printer driver and utility . Click Y es . After uninstallation, restart your system.
16.
17 About Media . . . . . . . . . . . . . . . . . . . . . . . . . . .18 In the Media T ray . . . . . . . . . . . . . . . . . . . . . . .18 On the Multi-purpose T ray . . . . . . . . . . . . . . . .19 Printing on T ransparency , Label or Envelope . . . .
Transparency Paper 18 Caution: B Do not use a media for ink jet that may be wrapped around the fuser roller and cause damage. Available media tray: A4 Paper A4 Transparency Letter Paper Letter Transparency Legal Paper Push down on the metal plate until it clicks, locking it in place.
19 Caution: B Do not use a media for ink jet that may be wrapped around the fuser roller and cause damage. ■ Setting media thickness switch Because of the most reliable paper-picking for various media weights, media thickness can be manually selected.
20 It is possible to see the following menus to configure the printer by printing the menu map. B Test page, Bias Adjustment, Maintenance, Image Area, Power Saver, Network Protocol Setup* 1 , Adjustment to Media, Language. * 1 This menu wil not appear if the network card is not installed in the printer.
21 This feature compensates for the changes in density that can occur as environmental conditions change, toner cartridges or the color imaging unit age.
22 Periodic cleaning of the printer is recommended. The frequency of cleaning is dependent upon the environment in which the printer is used. You should clean the printer: B At least once a month. B When the printer experiences frequent media jams. B When print quality has deteriorated.
23 Open the front door and check whether the media is jammed under the color imaging unit. If the media jam is not found, go to next step. B If the media is jammed, remove it by following Method B of Jam at B . To clear error message “Jam at C”, slide out the fuser unit, then slide it back to the printer.
24 Replace the oil supply roll into the fuser unit. Press down firmly on the oil supply roll to snap both sides into place. Open the front door and slide the fuser unit back into the printer (Refer to the illustration on step 2). Turn the small green thumbscrew clockwise to lock the fuser unit.
25 ■ Printing a T est Print Executing Test Print enables you to print the color halftone pages (Cyan, Magenta, Yellow and Black) to check the print quality. 1. Press the MENU/EXIT button on the printer panel. 2. Press the H H /ENTER button. 3. Press the F F /CONTINUE button twice.
26 Corrective Action Trouble Possible Cause Store media in the original, dust- free package in the same environmental conditions as the printer. Paper doesn’t match the environmental conditions, or it has too much moisture. Try fresh paper, or another type of paper.
27 Corrective Action Trouble Possible Cause Print 5-10 pages of blank pages to clean the roller. If you still see the problem: B Replace the oil supply roll. If you still see the problem: B Replace the fuser unit. A piece of the printed image is missing and reappears out of place, approximately 129 mm (5 ″ ) down the page.
28 * 1 Average life is based on an average of 5% coverage of the printable area and standard density for any one color (refer to Example A: Monochrome 5% coverage). For the components below, the average life may decrease depending on the percentage of colors and coverage used.
29 The average life of printer components ( color imaging unit, fuser unit and cleaning pad ) varies depending on the percentage of colors and coverage used. When printing at full color with high percentage of coverage, the average life of these components will be decreased.
30 ■ Media sizes/Margins and print area Refer to “Specifications” of the Operating Instructions installed on your computer. ■ T ypes of Paper to avoid B Extremely smooth or shiny paper or paper that is highly textured B Letterhead imprinted with low temperature or thermography.
31 The bidirectional parallel interface is based on the IEEE P1284-B standard. If your computer has a bidirectional parallel port, the printer driver and printer can take advantage of faster data transfer.
Panasonic Document Imaging Company, Division of Matsushita Electric Corporation of America, Two Panasonic Way, Secaucus, New Jersey 07094 Panasonic Sales Company (PSC) Division of Matsushita Electric of Puerto Rico, Inc. Ave. 65 de Infatería, Km. 9.5, San Gabriel Industrial Park Carolina, Puerto Rico 00985 Panasonic Canada Inc.
An important point after buying a device Panasonic KX-P8415 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Panasonic KX-P8415 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Panasonic KX-P8415 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Panasonic KX-P8415 you will learn all the available features of the product, as well as information on its operation. The information that you get Panasonic KX-P8415 will certainly help you make a decision on the purchase.
If you already are a holder of Panasonic KX-P8415, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Panasonic KX-P8415.
However, one of the most important roles played by the user manual is to help in solving problems with Panasonic KX-P8415. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Panasonic KX-P8415 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
