Instruction/ maintenance manual of the product 6138 Palsonic
Go to page of 18
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 61CM CORDLE.
. This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured.
OPERATING INSTRUCTION: POWER ON/OFF SWITCH Press the Power Switch, the appliance will be in "STANDBY" mode. A red light shows on the control panel. Press "PR-/+" buttons to turn on the set. The red light goes out, and a green light, shows on the control panel.
There are two ways to choose the channel number you want-the single-number method and the double-number method. Single-digit Method (highest Program Number is 9) This allows numbers 0 ~ 9 ONLY and is useful for limiting the number of channels if you do not mind some channels on the wrong number (10 and 28 could be put on 1 and 0, for instance).
VHF-1 When the set finds a TV signal, it will stop searching automatically, and show the TV picture on the screen. The tuning is optimised for strong signals. Weak signals may need fine tuning for the best result. If you want another channel, press the SEARCH button again.
The settings of picture and sound will be stored in memory until you reset them. TUNING & STORING A VCR The set is provided with Audio/Video sockets that allow direct connection to the VCR, but the set may also be used with the antenna connection.
Low (Left Speaker) THE CONTROL OF PICTURE AND SOUND Function select On the Front Panel, the "PICTURE" button is used to select the following functions: BRIGHTNESS, COLOUR, CONTRAST, BALANCE and VOLUME in that order. Each of the functions is adjusted by means of the adjacent -/+ level control buttons.
REMOTE CONTROL UNIT The remote control unit allows almost everything to be adjusted from the armchair. DIGITAL BUTTON 16 MUTE 9 VOLUME UP/DOWN 5 BRIGHTNESS UP/DOWN 2 PR (+/-) 6,7 RECALL 15 BATTERIES: 1. Remove the battery cover of Remote Control Unit.
11. S.MPX (Stereo switching) BUTTON LIST The trick is to push the buttons slowly; it takes a moment to register. Be careful that the button does not lock down. Some buttons behave differently in TV and Teletext. The following list is grouped according to TV or Teletext.
16. DIGITAL BUTTON In single-digit mode, press these buttons to select any of 0~9 channels. In double-digit mode, press these buttons to select any of 00~39 channels.
10 AUDIO OUTPUT AND DISPLAY ON SCREEN Transmission Mode Display on Screen Audio Output Mono STEREO : MONO Ineffective Stereo Dual. Sound STEREO MONO DUAL I DUAL II Stereo Mono (Forced) Sound I Sound I.
OUT Sockets These sockets take the signal OUT of the TV set and feed it TN to the VCR. They are hardly ever used. Most VCR’s have their own Tuner built in and do not need the TV set to tune the TV channel for them. The usual setup is to give the VCR the antenna, and feed the TV set out of the VCR’s RF output.
NOTE: * You can use either RF or Audio/Video input from the VCR, but the quality of picture and sound is better using the Audio/Video sockets. * If the VCR has Mono sound, connect it to the L/Mono input socket. The R/Stereo cable is optional for Stereo and need not be used.
Press AV Button (13) to switch to Video mode. The TV set will act as a monitor to help edit while dubbing. The set MUST remain in Video mode and MUST NOT be switched off during the session. 3. DUBBING The figure below shows how to connect TWO VCRs to the TV for dubbing one from the other.
CONNECTING EXTERNAL SPEAKERS You can connect speakers to the EXTERNAL SPEAKER terminals on the TV set to enhance sound from the TV. Note: Before connecting the external speakers, turn off your TV set. While pressing the button, insert the wire into the hole as shown below, and then release the button.
TROUBLE SHOOTING Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other similar causes. If any difficulty arises in the operation of your set, first check through this list of symptoms and correction. Should the difficulty cause concern, unplug the set and contact your dealer.
Specifications Colour System: Receivers Channel Cable Channel Stereo Power supply CRT Audio Output Antenna Impedance Dimension (mm) Weight Remote Control Unit Power Supply * Design and specifications are subject to change without notice.
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-64063-.
An important point after buying a device Palsonic 6138 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Palsonic 6138 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Palsonic 6138 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Palsonic 6138 you will learn all the available features of the product, as well as information on its operation. The information that you get Palsonic 6138 will certainly help you make a decision on the purchase.
If you already are a holder of Palsonic 6138, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Palsonic 6138.
However, one of the most important roles played by the user manual is to help in solving problems with Palsonic 6138. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Palsonic 6138 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
