Instruction/ maintenance manual of the product 300 Packard Bell
Go to page of 10
Packard Bell V ibe 300 Disassembly Manual.
1 Packard Bell Vibe 300 Disassembly Manual Table of Contents Overview 2 Technician Notes 2 Disassembly Instructio ns 2 Reassembly Instructions 2 Required Tools 2 Removing the Bottom C over 3 Removing .
2 Packard Bell Vibe 300 Disassembly Manual Overview This document contain s step-by-step disassemb ly instructions for the Vibe 300 MP3 pla yer. The instructions are illustra ted where necessary with imag es of the part that is be ing removed or disassembled.
3 Packard Bell Vibe 300 Disassembly Manual Removing the Bottom Cover 1. Remove three rubber stoppers (you do not need to remo ve the stopper located on the FM m odule cover.) Fig. 1 Remo ving the rubber stop pers. 2. Remove the FM Modu le cover. It has be en clicked into place, so you can easily push it out us ing a flat blade screwdriver.
Packard Bell Vibe 300 Disassembly Manual 4 Fig. 3 Vibe 30 0 without bottom cover. Removing the HDD To remove the HDD, first remove the bottom cover (see section Removing the Bottom Cover ) and then follow the steps below: 1. Disconnect micro drive (pull drive while holding the flat cable).
Packard Bell Vibe 300 Disassembly Manual 5 Fig. 5 Discon necting the battery from the main board. Removing the M ain Board / LCD Panel To remove the main boa rd / LCD panel, first r emove the bottom c.
Packard Bell Vibe 300 Disassembly Manual 6 Fig. 7 Disconn ecting the keypad flat cab le. 4. Separate the top cover and main board. 5. In case you need to replace the main board, disconnect the HDD flat cable: Push the two clip s in the indi cated direction (see Fig 8 ) and ta ke out the fl at cable.
Packard Bell Vibe 300 Disassembly Manual 7 7. Lift the LCD panel from the main board. The backside might be “ glued” , so you might need to apply some force .
Packard Bell Vibe 300 Disassembly Manual 8 button! The swi tch on the main board fits e xactly in the plastic switch locate d in the side panel. Fig. 12 Power button. n The rubber stopper s are keyed, so they only fit properly in on e way. Fig. 13 Keyed rubber stoppe r.
9 Packard Bell Vibe 300 Disassembly Manual Notice The infor mation in this guide i s subject to change withou t notice. This guide contains infor mation protected by copyright. No pa rt of this guide may be ph otocopied or reproduced in any for m or by any means w ithout prior written consent from NEC Computers Inte rnational B.
An important point after buying a device Packard Bell 300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Packard Bell 300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Packard Bell 300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Packard Bell 300 you will learn all the available features of the product, as well as information on its operation. The information that you get Packard Bell 300 will certainly help you make a decision on the purchase.
If you already are a holder of Packard Bell 300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Packard Bell 300.
However, one of the most important roles played by the user manual is to help in solving problems with Packard Bell 300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Packard Bell 300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
