Instruction/ maintenance manual of the product SWI-RC PAC
Go to page of 8
1 06-18-10 SWI-RC Universal Steering Wheel Control Interface Before Y ou Start A. Is this product compatible with the vehicle? • Please visit http://www .pac-audio.com/swixprogramming/swixprogramming.asp for the most current list of compatible vehicles.
2 SWI-RC Step 1 - Wiring Step A. Connect the BLACK wire to ground (-). V erication: Wire or location registers a constant (-) when probed. Step B. Connect the RED wire to switched +12V . V erication: Wire registers +12V when the ignition key is turned to the ACC or ON positions.
3 06-18-10 Step A. Refer to The V ehicle Application Guide or www.pac-audio.com/swixprogramming/swixprogramming.asp for the proper version number . Refer to the programming chart on page 4 for the proper radio select switch setting. Fill in the information below for quick reference.
4 Step B. Press and hold program - ming/mode button on SWI-RC. LED will light. Step C. Release programming/ mode button. SWI-RC SWI-RC SWI-RC SWI-RC Step 3 - Programming the SWI to Learn Steering Wheel Control Functions Step A. T urn the vehicle ignition to the ON position.
5 06-18-10 Programming the SWI-RC to Control the Head Unit (cont.) SWI-RC Once programming is completed, wait 7 seconds . The LED will ash three times indicating end of programming. The Interface will then ash the vehicle version number it was programmed for .
6 SWI-RC Step F . Repeat Steps D and E, using the TEMP DOWN Button. Step G. If the vehicle is equipped with F AN UP and F AN DOWN buttons: Repeat Steps D and E for these buttons as well. Step H. If the vehicle is NOT equipped with F AN UP and F AN DOWN buttons: Press and release the programming/ mode button on the SWI-RC.
7 06-18-10 Steering Wheel Interface Connect SWI white wire to resistors 47 100 150 560 1000 1500 47 = yel, vio, blk 100 = brn, blk, brn 150 = brn, grn, brn 560 = grn, blu, brn 1000 = brn, blk, red 1500 = brn, grn, red 3900 = org, wht, red 5100 = grn, brn, red Some vehicles have a separate wire for each of the steering wheel buttons.
8 Working on a new or unlisted vehicle? We are always looking for new vehicle information. If you’ve successfully completed the installation on a vehicle with steering wheel controls, and the vehicle is not listed in these instructions or on our Website, contact us at techsupport@pac-audio.
An important point after buying a device PAC SWI-RC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought PAC SWI-RC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data PAC SWI-RC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, PAC SWI-RC you will learn all the available features of the product, as well as information on its operation. The information that you get PAC SWI-RC will certainly help you make a decision on the purchase.
If you already are a holder of PAC SWI-RC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime PAC SWI-RC.
However, one of the most important roles played by the user manual is to help in solving problems with PAC SWI-RC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device PAC SWI-RC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
