Instruction/ maintenance manual of the product XT6 Orion
Go to page of 20
IN 226 Re v . C 11/10 Providing Exceptional Consumer Optical Products Since 1975 Customer Support (800) 676-1343 E-mail: support@telescope.com Corporate Offices (831) 763-7000 P .
2 Figure 1. The SkyQuest XT8 IntelliScope Secondar y mirror holder with 4-v ane spider (not visible) Finder scope Finder scope brac ket Eyepiece F ocuser Optical tube T ensioning knob IntelliScope Con.
3 Congratulations on y our purchase of an Orion SkyQuest XT IntelliScope Dobsonian . It is a high-per- f ormance astronomical instr ument designed to provide dazzling vie ws of celestial objects and unprecedented ease of use.
4 1 Azimuth encoder board 1 Encoder connector board 5 Encoder board mounting wood scre ws 1 Brass b ushing 1 Encoder disk 1 Azimuth axis he x-head screw (length 2.
5 the baseplate. Thread an encoder board mounting screw into the predrilled star ter hole with a Phillips screwdriver and tighten until just tight. 6. Place one T eflon bearing pad (G) into each recessed hole on the ground baseplate (A). The bearing pads will be loose in the recessed hole and should remain that wa y .
by adding or remo ving washers . This is impor tant when using the optional IntelliScope Computerized Object Locator , since the optical tube must be e xactly v er tical during the two-star alignment procedure. Installing the Eyepiece Rack The aluminum e yepiece rac k is a standard accessory on SkyQuest IntelliScope Dobsonians.
7 down much too freely . This causes problems when the observ- er tries to accurately center and track an object f or vie wing, especially at higher powers . Also, the telescope becomes v ery sensitive to balance , requiring additional equipment such as counterweight systems or springs to compensate.
8 spring-loaded tensioner on the brack et with your fingers (Figure 12b). Push the finder scope through the brack et until the O-ring seats just inside the front opening of the brack et. Now , release the tensioner and tighten the two blac k nylon screws a couple of turns each to secure the finder scope in place.
9 (left/right) (Figure 14). For altitude motion, the altitude bear- ings on the telescope tube glide on pairs of bearing cylinders made from ultra-high molecular weight (UHMW) poly eth yl- ene. For azim uth motion, the top baseplate mov es on three T eflon bear ing pads embedded in the ground baseplate.
10 Note: The image in both the finder scope and the main telescope will appear upside-down (r otated 180°). This is normal for finder scopes and reflector telescopes (see Figure 16). Now look through the finder scope . Ideally , the object should be within the field of view .
1200 mm = 120x 10 mm The maximum attainab le magnification for a telescope is directly related to how much light its optics can collect. A tele- scope with more light-collecting area, or aper ture, can yield higher magnifications than a smaller-aper ture telescope.
12 rethread the knobs back into the bearings so that you do not lose them. Do not use the navigation knob as a carry handle! It is not designed to suppor t the weight of the telescope tube and could break off or damage the tube. Note: The SkyQuest may be too heavy f or some users to lift and carry as one unit.
13 Preparing the T elescope for Collimation Once you get the hang of collimation, y ou will be able to do it quickly e v en in the dark. F or now , it is best to collimate in daylight, pref erab ly in a brightly lit room and aimed at a white wall. It is recommended that the telescope tube be oriented hor izontally .
14 Adjusting the Primary Mirror The final adjustment is made to the primar y mirror . It will need adjustment if , as in Figure 18d, the secondar y mirror is cen- tered under the f ocuser and the refl.
15 Note About the Collimatable 2" Focuser (XT8, XT10 only) The 2" f ocuser of the SkyQuest XT8 and XT10 can be colli- mated using three pairs of push-pull screws located at the base of the f ocuser (Figure 13). The focuser was collimated at the f actory howev er , and should nev er need to be adjusted.
night vision f or days . So give y ourself at least a little while to get used to the dark before y ou begin obser ving. T o see what you are doing in the darkness, use a red-filtered flashlight rather than a white light. Red light does not spoil your e yes ’ dark adaptation lik e white light does.
17 dark patches, and you ma y be ab le to spot a whitish polar ice cap . T o see surface detail on Mars , you will need a high po wer ey epiece and v er y steady air! D. The Stars Stars will appear as tiny points of light. Ev en powerful tele- scopes cannot magnify stars to appear as anything more than pinpoints.
18 location, the numbers get progressiv ely smaller . When the navigation n umbers reach 0, the telescope will be pointed right at the object! Y ou just look into the eyepiece and enjo y the view! The IntelliScope Computerized Object Locator is a wonderful conv enience f or both the novice and e xperienced observer .
19 8. Specifications SkyQuest XT6 IntelliScope Primar y mirror :150mm diameter , parabolic , center-marked F ocal length: 1200mm F ocal ratio: f/8.0 F ocuser :Rack-and-pinion.
20 One-Y ear Limited W arranty This Orion SkyQuest IntelliScope Dobsonian Reflecting T elescope is warranted against def ects in materials or workmanship for a period of one year from the date of purchase . This warranty is f or the benefit of the original retail purchaser only .
An important point after buying a device Orion XT6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion XT6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion XT6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion XT6 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion XT6 will certainly help you make a decision on the purchase.
If you already are a holder of Orion XT6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion XT6.
However, one of the most important roles played by the user manual is to help in solving problems with Orion XT6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion XT6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
