Instruction/ maintenance manual of the product XTRPRO104 Orion Car Audio
Go to page of 75
Subwoofer MODEL XTRPRO102 XTRPRO104 XTRPRO122 XTRPRO124 XTRPRO152 XTRPRO154 OWNER'S MANUAL.
© 2008 directed electronics—all rights reserved 1 T ABLE OF CONTENTS English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Français . . . . . . . . . . . . . . . . .
2 © 2008 directed electronics—all rights reserved WHA T’S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation. Listed below is a detailed list of the components included in this system package.
© 2008 directed electronics—all rights reserved 3 FEA TURES 12 3 5 6 7 4 8 9 10 11 12 13 14 15 Figur e 1 Figura 1 Abbildung 1 1 Polypropylene dust cap - moisture and UV resistant. 2 Oversized NBR (Nitrile-butadiene Rubber) surround for linear controlled long excursion.
4 © 2008 directed electronics—all rights reserved WIRING CONFIGURA TIONS Series - One Speaker (dual 2 ohm voice coils) One dual 2 ohm voice coil woofer with voice coils in connected in series results in a 4 ohm load to the amplifier . 2 ohm 2 ohm ++ + Figur e 2 Figura 2 Abbildung 2 __ _ 1.
© 2008 directed electronics—all rights reserved 5 Parallel — One Speaker (dual 4 ohm voice coils) One dual 4 ohm voice coil woofer with voice coils in parallel results in a 2 ohm load to the amplifier . 4 ohm 4 ohm ++ + Figur e 4 Figura 4 Abbildung 4 _ _ _ 1.
6 © 2008 directed electronics—all rights reserved Parallel - T wo Speaker (dual 4 ohm voice coils) T wo dual 4 ohm voice coil woofers with voice coils in parallel and the two woofers in parallel results in a 1 ohm load to the amplifier . 4 ohm 4 ohm + + -- 4 ohm 4 ohm + + -- + - Figur e 5 Figura 5 Abbildung 5 1.
© 2008 directed electronics—all rights reserved 7 Series/Parallel - T wo Speakers (dual 2 ohm voice coils) Note: V erify and ensur e that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil.
8 © 2008 directed electronics—all rights reserved Series/Parallel - Three Speakers (dual 4 ohm voice coils) Note: V erify and ensur e that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil.
© 2008 directed electronics—all rights reserved 9 Series/Parallel - Three Speakers (dual 2 ohm voice coils) Note: V erify and ensur e that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil.
10 © 2008 directed electronics—all rights reserved Series/Parallel - Four Speakers (dual 4 ohm voice coils) Note: V erify and ensur e that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil.
© 2008 directed electronics—all rights reserved 11 Series/Parallel - Four Speakers (dual 2 ohm voice coils) Note: V erify and ensur e that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil.
12 © 2008 directed electronics—all rights reserved 2 Amplifiers - One Speaker (dual 2 ohm voice coils) One dual 2 ohm voice coil woofer with each voice coil connected to an individual amplifier , resulting in a 2 ohm load to each amplifier . 2 ohm 2 ohm ++ -- + - + - Figur e 11 Figura 11 Abbildung 11 1.
© 2008 directed electronics—all rights reserved 13 2 Amplifiers - One Speaker (dual 4 ohm voice coils) One dual 4 ohm voice coil woofer with each voice coil connected to an individual amplifier , resulting in a 4 ohm load to each amplifier . 4 ohm 4 ohm ++ -- + - + - Figur e 12 Figura 12 Abbildung 12 1.
14 © 2008 directed electronics—all rights reserved SPECIFICA TIONS Model/Part Number XTRPRO102 XTRPRO104 XTRPRO122 Thiele/Small Parameters Fs (free-air resonance, Hz) 28.0 32.1 30.5 V as (equivalent compliance, cu. ft.) 0.681 0.587 1.198 V as (equivalent compliance, liters) 19.
© 2008 directed electronics—all rights reserved 15 SPECIFICA TIONS Model/Part Number XTRPRO124 XTRPRO152 XTRPRO154 Thiele/Small Parameters Fs (free-air resonance, Hz) 32.3 23.4 28.7 V as (equivalent compliance, cu. ft.) 1.256 3.464 3.207 V as (equivalent compliance, liters) 35.
16 © 2008 directed electronics—all rights reserved Enclosure Details Parameters listed are for conventional applications only , for further help please 1. call Audio T ech Support. At least 0.75" MDF (Medium Density Fiberboard) is recommend for any XTRPRO 2.
© 2008 directed electronics—all rights reserved 17 Explanation of Enclosure Specifications There are many different factors that help determine the best style of enclosure for you or your vehicle. Listed below are some factors that should be considered.
18 © 2008 directed electronics—all rights reserved ENCLOSURE RECOMMENDA TIONS Enclosure Details 1. External dimensions calculated for 3/4” building material 2. Includes speaker displacement 3. V olumes given are net tuning volume 4. Enclosures include a minimal amount of damping material.
© 2008 directed electronics—all rights reserved 19 XTRPRO102 & 104 V ented Enclosure Recommendations —Box P ar ts— Box Shape: Square Prism 1 T op , 1 Bottom: depth (c) = 11.39 in. (289 mm) width (b) = 15.5 in. (394 mm) thickness = 0.75 in. (19 mm) 1 F ront, 1 Back: height (a) = 10.
20 © 2008 directed electronics—all rights reserved XTRPRO122 & 124 Sealed Enclosure Recommendations c b —Bo x Parts— Bo x Shape: Square Prism 1 T op , 1 Bottom: depth (c) = 14.24 in. (362 mm) width (b) = 16 in. (406 mm) thickness = 0.75 in.
© 2008 directed electronics—all rights reserved 21 XTRPRO122 & 124 V ented Enclosure Recommendations —Box P ar ts— Box Shape: Square Prism 1 T op , 1 Bottom: depth (c) = 15.36 in. (390 mm) width (b) = 18.5 in. (470 mm) thickness = 0.75 in. (19 mm) 1 F ront, 1 Back: height (a) = 12 in.
22 © 2008 directed electronics—all rights reserved XTRPRO152 & 154 Sealed Enclosure Recommendations c b —Bo x Parts— Bo x Shape: Square Prism 1 T op , 1 Bottom: depth (c) = 15.52 in. (394 mm) width (b) = 17.5 in. (445 mm) thic kness = 0.75 in.
© 2008 directed electronics—all rights reserved 23 XTRPRO152 & 154 V ented Enclosure Recommendations —Box P ar ts— Box Shape: Square Prism 1 T op , 1 Bottom: depth (c) = 15.9 in. (404 mm) width (b) = 23.5 in. (597 mm) thickness = 0.75 in. (19 mm) 1 F ront, 1 Back: height (a) = 17 in.
© 2008 directed electronics—T ous droits réservés 25 FRANÇAIS INST ALLA TION Les performances de ces haut-parleurs de graves XTRPRO sont directement liées à la qualité de l’installation. Les précautions prises lors de l’installation se traduiront par des années de bon fonctionnement.
26 © 2008 directed electronics—T ous droits réservés CARACTÉRISTIQUES 12 3 5 6 7 4 8 9 10 11 12 13 14 15 1 Calotte pare-poussière en polypropylène, résistante à l’humidité et aux UV . 2 Suspension surdimensionnée en caoutchouc nitrile-butadiène permettant une longue course contrôlée.
© 2008 directed electronics—T ous droits réservés 27 CONFIGURA TIONS DE CÂBLAGE Série – Un haut-parleur (deux bobines mobiles de 2 ohms) V oir la figure 2 à la page 4 Un haut-parleur de graves à deux bobines mobiles de 2 ohms raccordées en série constitue une charge de 4 ohms pour l’amplificateur .
28 © 2008 directed electronics—T ous droits réservés (+) de l’amplificateur . Raccordez les bornes négatives (-) des haut-parleurs de graves à la borne négative (-) de l’amplificateur .
© 2008 directed electronics—T ous droits réservés 29 1. Configurez chaque haut-parleur de graves en série en raccordant la borne négative (-) de la première bobine à la borne positive (+) de la seconde. 2. Raccordez la borne positive (+) de la première bobine de chaque haut-parleur de graves à la borne positive (+) de l’amplificateur .
30 © 2008 directed electronics—T ous droits réservés (+) et négative (-) correspondantes du premier amplificateur . 2. Raccordez l’autre bobine mobile du haut-parleur au second amplificateur en reliant les bornes positive (+) et négative (-) du haut-parleur aux bornes positive (+) et négative (-) correspondantes du second amplificateur .
© 2008 directed electronics—T ous droits réservés 31 Sd (surface effective de rayonnement, cm2) Sd (surface effective de rayonnement, m2) Sd (surface effective de rayonnement, pouces-carrés) Pla.
32 © 2008 directed electronics—T ous droits réservés EXPLICA TION DES CARACTÉRISTIQUES TECHNIQUES DES CAISSONS De nombreux facteurs entrent en jeu dans la détermination du meilleur type de caisson pour un utilisateur ou un véhicule donné. V oici quelques uns de ces facteurs.
© 2008 directed electronics—T ous droits réservés 33 RECOMMANDA TIONS SUR LES ENCEINTES Détails des enceintes 1. Dimensions externes calculées pour des matériaux de 3/4” 2. Inclut le volume d'encombrement des haut-parleurs 3. Les volumes indiqués sont le volume d'accord net 4.
34 © 2008 directed electronics—T ous droits réservés Explication des diagrammes de caissons à évent accordé (voir les dimensions en pages 19, 21 et 23) c b a d c A B C h g e —Éléments du c.
© 2008 directed electronics—Reservados todos los derechos. 35 ESP AÑOL INST ALACIÓN El rendimiento de estos subwoofers XTRPRO es directamente proporcional a la calidad de la instalación. El cuidado que se tenga durante el proceso de instalación será recompensado con muchos años de rendimiento satisfactorio.
36 © 2008 directed electronics—Reservados todos los derechos. CARACTERÍSTICAS 12 3 5 6 7 4 8 9 10 11 12 13 14 15 1 T apa de polipropileno contra el polvo; resistente a la humedad y a los rayos ultravioleta. 2 Envolvente de Goma de Butadieno de Nitrilo (NBR) para grandes desplazamientos lineales controlados.
© 2008 directed electronics—Reservados todos los derechos. 37 CONFIGURACIONES DE CABLEADO En serie: un altavoz (dos bobinas acústicas de 2 Ω ) V ea la figura 2 en la página 4 Un woofer con dos bobinas acústicas de 2 Ω y las bobinas acústicas en serie produce una carga de 4 Ω en el amplificador .
38 © 2008 directed electronics—Reservados todos los derechos. negativa (-) del amplificador . En serie/paralelo: dos altavoces (dos bobinas acústicas de 2 Ω cada uno) V ea la figura 6 en la pági.
© 2008 directed electronics—Reservados todos los derechos. 39 En serie/paralelo: cuatro altavoces (dos bobinas acústicas de 4 Ω cada uno) V ea la figura 9 en la página 10 Nota: V erifique y aseg.
40 © 2008 directed electronics—Reservados todos los derechos. Un woofer con 2 bobinas acústicas de 4 Ω y cada bobina acústica conectada a su propio amplificador produce una carga de 4 Ω en cada amplificador .
© 2008 directed electronics—Reservados todos los derechos. 41 Diámetro del agujero de montaje (plg./mm) Profundidad de montaje (plg./mm) Peso del imán (oz.
42 © 2008 directed electronics—Reservados todos los derechos. EXPLICACIÓN DE LAS ESPECIFICACIONES DE LAS CAJAS Hay muchos factores que contribuyen a determinar el mejor estilo de caja para usted o su vehículo. A continuación se presentan algunos factores que se deben tener en cuenta.
© 2008 directed electronics—Reservados todos los derechos. 43 RECOMENDACIONES P ARA LA CAJA Detalles de la caja 1. Las dimensiones externas se han calculado para un material de construcción de ¾ plg. de grosor 2. Incluye el desplazamiento del altavoz 3.
44 © 2008 directed electronics—Reservados todos los derechos. T raducción del diagrama de la caja ventilada (las medidas se encuentran en las pági- nas 19, 21 y 23) c b a d c A B C h g e —P ar .
© 2008 directed electronics—Alle Rechte vorbehalten 45 DEUTSCH INST ALLA TION Die Leistung dieser XTRPRO-Subwoofer hängt direkt von der Qualität der Installation ab. Ein sorgfältiges V orgehen bei der Installation garantiert Ihnen jahrelange Höchstleistungen.
46 © 2008 directed electronics—Alle Rechte vorbehalten HÖHEPUNKTE 12 3 5 6 7 4 8 9 10 11 12 13 14 15 1 Feuchtigkeits- und UV-beständige Polypropylen-Abdeckung 2 Extra große Sicke aus NBR (Nitril.
© 2008 directed electronics—Alle Rechte vorbehalten 47 SCHAL TKONFIGURA TIONEN Reihe — Ein Lautsprecher (Doppelte 2-Ohm-Schwingspulen) Siehe Abbildung 2 auf Seite 4 Ein T ieftöner mit doppelten 2-Ohm-Schwingspulen, bei dem die Schwingspulen in Reihe geschaltet sind: Lastwiderstand von 4 Ohm am V erstärker .
48 © 2008 directed electronics—Alle Rechte vorbehalten 2. Verbinden Sie die positiven (+) T erminals der Tieftöner mit dem positiven (+) T erminal am Verstärker . V erbinden Sie die negativen (+) T erminals der Tieftöner mit dem negativen (+) T erminal am Verstärker .
© 2008 directed electronics—Alle Rechte vorbehalten 49 Lastwiderstand von 1,33 Ohm am V erstärker . 1. Schließen Sie jeden Tieftöner in Reihe an, indem Sie das negative (-) T erminal der ersten Schwingspule mit dem positiven (+) T erminal der zweiten Spule verbinden.
50 © 2008 directed electronics—Alle Rechte vorbehalten 2 V erstärker — Ein Lautspr echer (Doppelte 2-Ohm-Schwingspulen) Siehe Abbildung 11 auf Seite 12 Ein T ieftöner mit doppelten 2-Ohm-Schwingspulen, bei dem jede Schwingspule an einen separaten V erstärker angeschlossen ist: Lastwiderstand von 2 Ohm am V erstärker .
© 2008 directed electronics—Alle Rechte vorbehalten 51 Le (Induktivität, mh) Wirkungsgrad (1 W bei 1 M, dB) Wirkungsgrad (2.86 V bei 1 M, dB) Xmax (linearer Hub in eine Richtung, Zoll) Xmax (linea.
52 © 2008 directed electronics—Alle Rechte vorbehalten angebracht wäre, und bei 90 und mehr empfehlen wir ein Bassreflexgehäuse. *** Subsonic-Filter sollten immer verwendet und speziell an Bassreflexgehäuse angepasst werden. ERLÄUTERUNG DER GEHÄUSEDA TEN Es gibt viele verschiedene Faktoren, die den besten Gehäusetyp für Sie bzw .
© 2008 directed electronics—Alle Rechte vorbehalten 53 GEHÄUSEEMPFEHLUNGEN Gehäusedetails 1. Für Baumaterial mit ¾ Zoll (1,9 cm) Dicke berechnete Außenmaße 2. Einschließlich Lautsprecherhub 3. Angegebene V olumen sind Netto-T uningvolumen 4.
54 © 2008 directed electronics—Alle Rechte vorbehalten Erklärung des Diagramms für Bassreflexgehäuse (Maße finden Sie auf S. 19, 21 und 23) c b a d c A B C h g e —Gehäuseteile— Gehäusefor.
© 2008 directed electronics—tutti i diritti riservati 55 IT ALIANO INST ALLAZIONE I risultati conseguibili con questi subwoofer XTRPRO dipendono direttamente dalla qualità dell’installazione; eseguendola con cautela si avrà la certezza di ottenere un suono soddisfacente per anni e anni.
56 © 2008 directed electronics—tutti i diritti riservati CARA TTERISTICHE 12 3 5 6 7 4 8 9 10 11 12 13 14 15 1 Protezione parapolvere in polipropilene - resistente all’umidità e ai raggi ultravioletti. 2 Surround maggiorato in NBR (gomma nitrile butadiene) per lunga escursione lineare controllata.
© 2008 directed electronics—tutti i diritti riservati 57 CONFIGURAZIONI DI CABLAGGIO Un diffusor e in serie (con due bobine mobili da 2 ohm) V edi Figura 2 a pagina 4 Un woofer con due bobine mobili da 2 ohm collegate in serie, applica un carico di 4 ohm all’amplificatore.
58 © 2008 directed electronics—tutti i diritti riservati (-) dell’amplificatore. Due diffusori in serie-parallelo (ciascuno con due bobine mobili da 2 ohm) V edi Figura 6 a pagina 7 Nota: verific.
© 2008 directed electronics—tutti i diritti riservati 59 Quattro dif fusori in serie-parallelo (ciascuno con due bobine mobili da 4 ohm) V edi Figura 9 a pagina 10 Nota: verificare che i woofer sia.
60 © 2008 directed electronics—tutti i diritti riservati separato, applica un carico di 4 ohm a ciascun amplificatore. 1. Collegare una delle bobine mobili del woofer al primo amplificatore collegandone il terminale positivo (+) e quello negativo (-) rispettivamente al terminale positivo (+) e a quello negativo (-) dell’amplificatore stesso.
© 2008 directed electronics—tutti i diritti riservati 61 Profondità di montaggio (pollici/millimetri) Peso magneti (oz) Diametro telaio (pollici/millimetri) Casse raccomandate Cassa sigillata tipi.
62 © 2008 directed electronics—tutti i diritti riservati SPIEGAZIONE DEI DA TI TECNICI DELLA CASSA Il tipo migliore di cassa per le esigenze del proprietario o le condizioni del veicolo dipende da numerosi fattori, alcuni dei quali sono elencati di seguito.
© 2008 directed electronics—tutti i diritti riservati 63 RACCOMANDAZIONI PER LA CASSA Dettagli della cassa 1. Le misure esterne sono calcolate in base a un materiale da costruzione spesso 19 mm (0,75 in). 2. Comprendono il volume interno del diffusore.
64 © 2008 directed electronics—tutti i diritti riservati Legenda relativa alla cassa ventilata (vedi pagine 19, 21 e 23 per le misure) c b a d c A B C h g e —P ar ti della cassa— Forma della ca.
© 2008 directed electronics—T odos os direitos reservados 65 POR TUGUÊS INST ALAÇÃO O desempenho dos subwoofers XTRPRO é diretamente proporcional à qualidade da instalação. O cuidado durante o processo de instalação será recompensado com anos de satisfação com o desempenho.
66 © 2008 directed electronics—T odos os direitos reservados CARACTERÍSTICAS 12 3 5 6 7 4 8 9 10 11 12 13 14 15 1 Cobertura contra pó de polipropileno resistente à umidade e radiação ultravioleta. 2 Surround de borracha nitrílica (NBR) grande para longo deslocamento linear controlado.
© 2008 directed electronics—T odos os direitos reservados 67 CONFIGURAÇÕES DE CONEXÃO Em série – Um alto-falante (duas bobinas de 2 ohm) V er figura 2 na página 4 Um woofer com duas bobinas móveis de 2 ohm conectadas em série resulta em uma carga de 4 ohm ao amplificador .
68 © 2008 directed electronics—T odos os direitos reservados (-) do amplificador . Série-Paralela – Dois alto-falantes (duas bobinas de 2 ohm) V er figura 6 na página 7 Nota: V erifique e certi.
© 2008 directed electronics—T odos os direitos reservados 69 positivo (+) do amplificador . Conecte o terminal negativo (-) da segunda bobina de cada woofer ao terminal negativo (-) do amplificador .
70 © 2008 directed electronics—T odos os direitos reservados Dois amplificadores – Um alto-falante (duas bobinas móveis de 4 ohm) V er figura 12 na página 13 Um woofer com duas bobinas móveis de 4 ohm com cada bobina conectada a um amplificador , resultando em uma carga de 4 ohm a cada amplificador .
© 2008 directed electronics—T odos os direitos reservados 71 Produto de eficiência da largura de banda (EBP) ** Dimensão física do alto-falante Deslocamento do alto-falante (pés cúbicos) Diâmetro do orifício de montagem do alto-falante (pol.
72 © 2008 directed electronics—T odos os direitos reservados EXPLICAÇÃO DAS ESPECIFICAÇÕES DAS CAIXAS Existem muitos fatores diferentes que ajudam a determinar o melhor estilo de caixa para o usuário ou o veículo.
© 2008 directed electronics—T odos os direitos reservados 73 RECOMENDAÇÕES P ARA CAIXAS Detalhes da caixa 1. Dimensões externas calculadas para material de construção de 190 mm (3/4”) de espessura. 2. Inclui o deslocamento do alto-falante. 3.
74 © 2008 directed electronics—T odos os direitos reservados T radução do diagrama da caixa ventilada (ver as medidas nas páginas 19, 21 e 23) c b a d c A B C h g e —P ar tes da caixa— Forma.
© 2008 Directed Electronics. All rights reser ved. GXTRPRO102 2008-11 Vista, CA 92081 WWW .DIRECTED.COM Directed Electronics is committed to delivering world class quality products and ser vices that excite and delight our customers. Directed Electronics is an ISO 9001 registered company.
An important point after buying a device Orion Car Audio XTRPRO104 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio XTRPRO104 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio XTRPRO104 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio XTRPRO104 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio XTRPRO104 will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio XTRPRO104, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio XTRPRO104.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio XTRPRO104. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio XTRPRO104 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
