Instruction/ maintenance manual of the product XTR52 Orion Car Audio
Go to page of 29
Component Speaker MODEL XTR52 XTR62 OWNER'S MANUAL.
© 2008 directed electronics—all rights reserved 1 T ABLE OF CONTENTS English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Français . . . . . . . .
2 © 2008 directed electronics—all rights reserved Model Number: _____________________________ Serial Number: _____________________________ Date of Purchase: _____________________________ WHA T’S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation.
© 2008 directed electronics—all rights reserved 3 the location you have chosen will not affect any of the mechanical or electrical operations of the vehicle. Determining the best location for the speakers will depend on your cosmetic needs and your vehicle's interior .
4 © 2008 directed electronics—all rights reserved INST ALLING THE MID/WOOFERS Step 1: Determine where the speakers will be mounted. Make sure there is a flat area large enough for the speakers to fit properly . An uneven mounting surface can damage the driver .
© 2008 directed electronics—all rights reserved 5 INST ALLING THE TWEETER SURF ACE MOUNTING Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Place the provided template or tweeter cup against the panel and mark the two holes at the rear of the housing.
6 © 2008 directed electronics—all rights reserved Step 5: Install tweeter in flush mount housing. Step 6: Connect the speaker wires observing the correct polarity . Step 7: Install tweeter and housing in the hole cut for mounting, so that the trim ring is flat with the front of the surface.
© 2008 directed electronics—all rights reserved 7 WIRING DIAGRAM T o Woofer T o T weeter T o Amplifier Note: The tweeter positive is the wire marked with the stripe. Note: Le câble positif du haut-parleur d'aigus est rayé. Nota. El positivo del tweeter es el cable que tiene la franja.
8 © 2008 directed electronics—all rights reserved SPECIFICA TIONS Model XTR52 XTR62 Nominal Impedance 4 Ω 4 Ω Power Continuous/Maximum 50 /100 W 60 /120 W Frequency Response 80 - 22kHz 75 - 22kHz Sensitivity (2.83V @ 1M) 88dB 90dB Mounting Depth 2.
© 2008 directed electronics—T ous droits réservés 9 FRANÇAIS OÙ MONTER LES HAUT -P ARLEURS Le choix du bon emplacement des haut-parleurs aura un effet majeur sur la qualité du son du système. Plusieurs choses doivent être prises en considération pour faire le meilleur choix.
10 © 2008 directed electronics—T ous droits réservés A TTENTION: Vérifiez l'espace libre du mécanisme et des fils électriques des fenêtres AV ANT de percer . Étape 5: Amenez les câbles à leurs haut-parleurs. Assurez-vous de les garder loin de tout bord métallique ou autre aiguisé.
© 2008 directed electronics—T ous droits réservés 11 Étape 8: Utilisez le support en croix et la vis inclus pour fixer le boîtier sur la surface.. INST ALLA TION DU RÉP ARTITEUR Étape 1: Décidez où fixer le répartiteur , loin de tout fil électrique, d'origine ou installé après coup.
© 2008 directed electronics—Reservados todos los derechos. 13 ESP AÑOL UBICACIONES DE MONT AJE DE LOS AL T A VOCES Escoger la ubicación correcta de los altavoces tendrá el mayor efecto en la calidad del sonido del sistema.
14 © 2008 directed electronics—Reservados todos los derechos. * Sierra circular de 4 3/4 plg. (woofer de 5 1/4 plg.) * Sierra circular de 5 plg. (woofer de 6 1/2 plg.) ADVERTENCIA: V erifique que haya espacio para los mecanismos de ventana y los cables eléctricos ANTES de taladrar .
© 2008 directed electronics—Reservados todos los derechos. 15 Paso 4. Haga el agujero para el tweeter . Cuando instale el tweeter en ubicaciones de fábrica, este paso se puede omitir . Se puede hacer el agujero con unas tijeras de metal o una sierra circular de 2 plg.
16 © 2008 directed electronics—Reservados todos los derechos. Bobina de voz Alambre de cobre de 2 capas en un formador Kapton T weeter Domo de seda - Ferrofluido Araña Conex entrelazado de una pie.
© 2008 directed electronics—Alle Rechte vorbehalten 17 DEUTSCH SO PLA TZIEREN SIE DIE LAUTSPRECHER Die Wahl der korrekten Lautsprecherposition hat große Auswirkungen auf die Soundqualität des Systems. Bei der Wahl der Lautsprecherposition, die Ihren Ansprüchen am besten entspricht, sind mehrere Faktoren zu beachten.
18 © 2008 directed electronics—Alle Rechte vorbehalten WARNUNG: Prüfen Sie VOR dem Bohren, dass Sie keine Fenstermechanismen oder Stromkabel anbohren. 5. Schritt: V erlegen Sie die Lautsprecherkabel zu den Lautsprechern. Dabei müssen Sie die Kabel von scharfen Metallkanten oder anderen Kanten entfernt halten.
© 2008 directed electronics—Alle Rechte vorbehalten 19 WARNUNG: Prüfen Sie VOR dem Bohren, dass Sie keine Fenstermechanismen oder Stromkabel anbohren. 5. Schritt: Installieren Sie den Hochtöner im bündig eingebauten Gehäuse. 6. Schritt: Schließen Sie die Lautsprecherkabel an, wobei Sie auf die korrekte Polung achten müssen.
20 © 2008 directed electronics—Alle Rechte vorbehalten Zentriermembran Conex, einfach verknüpft Körbe aus Stahlblech mit Euro-Befestigungskonfiguration Zweiwegsysteme haben spezielle Crossover-Einheiten mit 6 dB Hochpass, 6 dB T iefpass und Hochtönerschutz.
© 2008 directed electronics—tutti i diritti riservati 21 IT ALIANO INDIVIDUAZIONE DELLA POSIZIONE DI MONT AGGIO DEGLI AL TOP ARLANTI La scelta della posizione degli altoparlanti ha la massima influenza sulla qualità del suono dell'impianto.
22 © 2008 directed electronics—tutti i diritti riservati o una sega a tazza della misura dell'altoparlante indicata di seguito. o sega a tazza da 4-3/4" (per installare un woofer da 5-1/4.
© 2008 directed electronics—tutti i diritti riservati 23 Fase 4: praticare il foro per il tweeter . Quando si inserisce l'altoparlante nelle sedi predisposte in fabbrica, è possibile tralasciare queste operazioni. Eseguire il foro con un paio di forbici da lattoniere o con una sega a tazza da 50,8 mm (2") per materiali duri.
24 © 2008 directed electronics—tutti i diritti riservati T weeter Cupola in seta - Ferrofluido Centratore Conex intrecciato T elai in acciaio stampato con configurazioni di montaggio europee Gli im.
© 2008 directed electronics—T odos os direitos reservados 25 POR TUGUÊS DETERMINAÇÃO DOS LOCAIS P ARA INST ALAÇÃO DOS AL TOS-F ALANTES A seleção dos locais corretos para instalação dos alto-falantes é o fator que mais influenciará a qualidade do som produzido pelo sistema.
26 © 2008 directed electronics—T odos os direitos reservados ser cortado com uma tesoura para metal fina, uma serra tico-tico ou a ar , ou uma serra copo correspondente ao tamanho do alto-falante de graves médios descrito abaixo.
© 2008 directed electronics—T odos os direitos reservados 27 metal ou uma serra copo de 50.8 mm (2”) para materiais duros. A TENÇÃO: Verifique se há espaço suficiente até os mecanismos e fios elétricos de operação do vidro da janela ANTES de perfurar .
28 © 2008 directed electronics—T odos os direitos reservados Aranha Conex entrelaçado simples Carcaças de aço estampado com configurações de instalação européias Sistemas bidirecionais com .
© 2008 Directed Electronics. All rights reserved GXTR52 2008-10 Vista, CA 92081 WWW .DIRECTED.COM Directed Electronics is committed to delivering world class quality products and ser vices that excite and delight our customers. Directed Electronics is an ISO 9001 registered company .
An important point after buying a device Orion Car Audio XTR52 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio XTR52 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio XTR52 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio XTR52 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio XTR52 will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio XTR52, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio XTR52.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio XTR52. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio XTR52 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
