Instruction/ maintenance manual of the product 4002 Orion Car Audio
Go to page of 18
.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Limited T wo-Y ear Consumer W arranty .
INTRODUCTION Thank you for your purchase of Orion's 4002 or 6002 amplifier . Each Orion amplifier is designed to be the leader in its class offering the most power , advanced features, and ease of use. Orion amplifiers are designed as the best affordable high end car audio amplifier money can buy .
LIMITED TWO-YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal use, .
SPECIFICA TIONS 1. All channels driven, continuous 4 W load 20Hz to 20kHz, < 0.05% THD, with input voltage at 13.8VDC. 2. All channels driven, continuous 2 W load 20Hz to 20kHz, < 0.
END P ANEL LA YOUT 1. Power LED - when lit indicates that the amplifier is on. 2. Stereo/Mono Switch - configures the amplifier for one or two inputs. 3. Gain Control - continuously adjusts from 200mV to 5V for full power output. 4. Copy/Master Switch - Determines the output of the RCA outputs.
Stereo / Mono Input Configuration The STEREO / MONO switch routes input from the front inputs to the rear section of the amplifier . This allows the Orion 4002 and 6002 amplifiers to utilize a single RCA or high- level input to feed signal to both the right and left channels of the amplifier .
High-Pass Crossover When the switch is to the right (OFF position), the high-pass crossover is bypassed. When the switch is to the left (ON position), the high-pass crossover is active. The high-pass crossover is continuously variable from 20Hz to 3kHz.
Speaker Connections T wo-Channel Stereo Configuration ● Lowest recommended impedance is 2 W stereo. ● Stereo input should be used for this configuration. ● Outputs can be configured for high-pass, low-pass, or full range operation. Mono Bridged Configuration ● Lowest recommended impedance is 4 W bridged mono.
Single-Channel Bridged Configuration ● Lowest recommended impedance is 4 W mono. ● Mono input must be used for this configuration. Only the Left input is used.
AMPLIFIER INST ALLA TION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery , alternator or the use of a storage capacitor . W e strongly recommend the use of a Directed Audio Essentials power capacitor with an extra battery in larger stereo systems.
amplifier is twisted or bent. Step 6 T urn the vehicle's key switch to the off position. Step 7 Disconnect the vehicle's battery ground terminal. Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and RGC). Step 9 Connect the RCA and speaker wires to the amplifier .
Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system. Adjusting the sound of the system is accomplished by setting the level controls and adjusting the internal crossovers. Step 1 T urn the signal source volume control all the way down.
T r oubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse.
Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed.
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under .
An important point after buying a device Orion Car Audio 4002 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Orion Car Audio 4002 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Orion Car Audio 4002 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Orion Car Audio 4002 you will learn all the available features of the product, as well as information on its operation. The information that you get Orion Car Audio 4002 will certainly help you make a decision on the purchase.
If you already are a holder of Orion Car Audio 4002, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Orion Car Audio 4002.
However, one of the most important roles played by the user manual is to help in solving problems with Orion Car Audio 4002. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Orion Car Audio 4002 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
