Instruction/ maintenance manual of the product 100 Oricom
Go to page of 16
Baby Monitor Secure 100 User Guide.
T ABLE OF CONTENTS W ARNINGS AND SAFETY INFORMA TION 1 GETTING ST ARTED 3 YOUR BABY MONITOR 5 BASIC OPERA TION 8 TROUBLESHOOTING 11 PRODUCT SPECIFICA TIONS 12 GUARANTEE 13.
1 W ARNINGS AND SAFETY INFORMA TION IMPORTANT Please read this user guide thoroughly before use. Your ORICOM Baby Monitor is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision of a child.
2 W ARNINGS AND SAFETY INFORMA TION Battery requirements Each parent unit requires two rechargeable Ni-MH batteries, size AAA 1.2V 800mAh (HR10/44). • Do not dispose of the batteries in a fi re, as they can explode. • Do not open, unscrew or temper with any of your baby monitor units or battery.
3 Installation For the Parent Unit 1 Remove the Belt Clip by lifting the clip at the top and sliding it downwards. 2 Then remove the battery cover on the back of the Parent Unit by pressing and sliding it down. Insert the rechargeable batteries (supplied) as marked on the unit and close the cover again.
4 5 Press [ ] to turn the Parent Unit on. • Before fi rst use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 15-16 hours. During this time, the Parent Unit will operate from the Charger pod when switched on.
5 YOUR BABY MONITOR Baby unit (Sender) 1 Night light Key Press to turn On the night light. Press again to turn off the Light. 2 Power On/Off Key Press to turn the Unit ON. Press and hold to turn the Unit OFF. 3 Page Key Press and hold this key, Parent unit makes an audible alert.
6 YOUR BABY MONITOR Left view of baby unit 6 DC 6V input Connecting to Power Adaptor. 7 8 9 10 6 Parent unit (Receiver) 7 Battery Cover Rechargeable batteries. 8 Belt Clip 9 Volume Up/Down Keys Adjust the Volume at which you hear the sounds in your baby's room.
7 Charger Pod 14 Charging Light When Parent unit is placed in the Charger Pod, the red charger light comes ON to indicate the batteries are charging. Light will remain ON to ensure optimum charge is maintained. 14 11 13 12 YOUR BABY MONITOR 11 Power Light Red light when the power is ON.
8 BASIC OPERA TION Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby's room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels.
9 BASIC OPERA TION • To stop the Page alert, press any button on the Parent Unit, or press [ ] again on the Baby Unit. Note: If no button is pressed, the paging tone will stop after 2 minutes. If the Parent Unit volume is off, the Parent Unit volume will reset to mid volume.
10 BASIC OPERA TION 8 lights illuminated fully charged 6 lights illuminated half charged 4 lights illuminated battery is running low 2 lights illuminated (alarm beep sounds) batteries need recharging Note: The parent unit can be used on or off the charger pod.
11 TROUBLESHOOTING Problem Possible cause(s) The red power lights do not turn on when you plug in the power. 1. Check if the units are properly connected to the power supply.
12 PRODUCT SPECIFICA TIONS Feature Speci fi cations Operating Frequency DECT 1.8 GHz Range Up to 300m under optimum conditions. The range is reduced in buildings (up to 50m) as a result of walls, doors etc.
13 GUARANTEE Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Practices Act 1974 or any other similar legislation.
Australia Oricom International Pty Ltd Locked Bag 658 South Windsor, NSW 2756 Customer Support Email: support@oricom.com.au Web: www.oricom.com.au Phone: 1300 889 785 Fax: (02) 4574 8898.
An important point after buying a device Oricom 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oricom 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oricom 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oricom 100 you will learn all the available features of the product, as well as information on its operation. The information that you get Oricom 100 will certainly help you make a decision on the purchase.
If you already are a holder of Oricom 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oricom 100.
However, one of the most important roles played by the user manual is to help in solving problems with Oricom 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oricom 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
