Instruction/ maintenance manual of the product RMR613HGA Oregon Scientific
Go to page of 17
W ireless Thermo-Hygro Clock Model : RMR613HGA User Manual RMR613HGA lab test cover R 2 1/8/04, 7:02 PM 1.
EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .
EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless Thermo-Hygro Clock (RMR613HGA). This device bundles precise time keeping, dual alarm, and temperature and humidity monitoring features into a single tool you can use from the convenience of your home.
EN 3 PRODUCT OVERVIEW FRONT VIEW 1. Clock / Alarm Area: Date, time, dual alarm; and Atomic Clock reception status 2. T emperature Area: Readings; sensor channel number; remote unit reception and battery status 3. Humidity / Comfort Zone Area: Readings, comfort zone and battery status.
EN 4 BACK VIEW 1. MEM: view current, maximum, and minimum temperature / humidity readings 2. DOWN: decrease setting / deactivate radio- controlled clock / activate or deactivate alarm 3. UP: increase setting / activate radio-controlled clock / activate or deactivate alarm 4.
EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1 2 1 2 3 4 1. W all mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) RM.
EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo/ Hygro Sensor that collects T emperature and Humidity data.
EN 7 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor . (Refer to the Search for Sensor section for more information.
EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure.
EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold DOWN for 2 seconds. Then, manually set the clock following the “Set Clock” instructions (below).
EN 10 ACTIV A TE ALARM Press ALARM to switch to Weekday or Single Alarm view . To activate or deactivate the alarm, press UP or DOWN . • Alarm deactivated: --:-- • Alarm activated: Alarm time is shown The bell icons W and S indicate the alarm display mode selected.
EN 11 To auto-scan between sensors, press and hold CHANNEL for 2 seconds. Each sensor's data will be displayed for 3 seconds. T o end auto-scan, press CHANNEL or MEM . If you use a sensor that collects only temperature data, humidity will not be shown.
EN 12 Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The technical specification of this product and contents of this user guide are subject to change without notice. Images not drawn to scale.
EN 13 Problem Symptom Remedy Data does not match main unit Initiate a manual sensor search ( 8) Cannot change channel Check sensors. Only one sensor is working ( 6) Check batteries ( 6) Check location ( 6) Remote sensor Cannot locate remote sensor SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 123 x 49.
EN 14 Calendar MM/DD; weekday in 5 languages (E, D, F , I, S) Alarm Weekday and Single Alarm; 2- minute crescendo POWER Main unit batteries 2 x UM-3 (AA) 1.5V alkaline Sensor batteries 2 x UM-4 (AAA) 1.5V alkaline FCC ST A TEMENT This device complies with Part 15 of the FCC Rules.
EN 15 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead.
P/N.: 086-003326-01 © 2004 Oregon Scientific. All rights reserved. RMR613HGA lab test back cover 12/29/03, 10:49 PM 1.
An important point after buying a device Oregon Scientific RMR613HGA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oregon Scientific RMR613HGA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oregon Scientific RMR613HGA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oregon Scientific RMR613HGA you will learn all the available features of the product, as well as information on its operation. The information that you get Oregon Scientific RMR613HGA will certainly help you make a decision on the purchase.
If you already are a holder of Oregon Scientific RMR613HGA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oregon Scientific RMR613HGA.
However, one of the most important roles played by the user manual is to help in solving problems with Oregon Scientific RMR613HGA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oregon Scientific RMR613HGA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
