Instruction/ maintenance manual of the product RMR603HGA Oregon Scientific
Go to page of 17
W ireless Thermo-Hygro Clock Model : RMR603HGA User Manual RMR603HGA lab test cover R2 1/14/04, 1:31 AM 1.
EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .
EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless Thermo-Hygro Clock (RMR603HGA). This device bundles precise time keeping, alarm, and temperature and humidity monitoring features into a single tool you can use from the convenience of your home.
EN 3 PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT : Press to activate backlight or snooze. 2. T emperature Area: Readings, trend line, sensor reception status and channel number 3.
EN 4 BACK VIEW 1. W all mount 2. Battery compartment 3. ° C / ° F switch 4. ZONE: Press to switch time zones, deactivate Atomic Clock signal reception 5.
EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1 2 1 2 3 4 1. W all mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) RM.
EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. T ABLE ST AND OR W ALL MOUNT Insert the stand on the back of the product, or mount it on a wall with a nail.
EN 7 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor . (Refer to the Sensor Data T ransmission section for more information.
EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure.
EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold ZONE for 2 seconds. Then, manually set the clock following the "Set Clock" instructions (below).
EN 10 ACTIV A TE ALARM Press ((.)) to activate or deactivate the Alarm. shows in the Clock Area when the Alarm is activated. SNOOZE ALARM Press SNOOZE/LIGHT to silence the Alarm for 8 minutes. If no button is pressed, the Alarm will automatically silence after 2 minutes.
EN 11 If you use a sensor that collects only temperature data, humidity will not be shown. MINIMUM / MAXIMUM RECORDS Press MEM to toggle between current, maximum (MAX) and minimum (MIN) records for the selected sensor . T o clear the records, press and hold MEM for 2 seconds.
EN 12 W ARNINGS This product is designed to give you years of service if handled properly . Observe the following guidelines: • Never immerse the product in water . This can cause electrical shock and damage the product. • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity .
EN 13 SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H1 16 x 125 x 57 mm (4.57 x 4.92 x 2.24 inches) We ight 7.90 ounces with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.
EN 14 FCC ST A TEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
EN 15 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead.
© 2004 Oregon Scientific. All rights reserved. P/N.: 086-003347-01 RMR603HGA lab test back cover 12/29/03, 10:29 PM 1.
An important point after buying a device Oregon Scientific RMR603HGA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oregon Scientific RMR603HGA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oregon Scientific RMR603HGA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oregon Scientific RMR603HGA you will learn all the available features of the product, as well as information on its operation. The information that you get Oregon Scientific RMR603HGA will certainly help you make a decision on the purchase.
If you already are a holder of Oregon Scientific RMR603HGA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oregon Scientific RMR603HGA.
However, one of the most important roles played by the user manual is to help in solving problems with Oregon Scientific RMR603HGA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oregon Scientific RMR603HGA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
