Instruction/ maintenance manual of the product BAR608HGA Oregon Scientific
Go to page of 18
W ireless W eather Station Model : BAR608HGA User Manual BAR608HGA lab test cover R 2 1/8/04, 6:38 PM 1.
EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .
EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless W eather Station (BAR608HGA). This device bundles precise time keeping, weather forecast, barometric trend with altitude adjustment, and indoor and outdoor temperature and humidity monitoring features into a single tool you can use from the convenience of your home.
EN 3 PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT button 2. Weather Forecast & Barometric T rend Area 3. Outdoor T emperature & Humidity Area 4. Indoor T emperature & Humidity Area 5. Clock / Alarm Area 6 Moon Phase 7. and : increase or decrease setting / activate or deactivate Atomic Clock.
EN 4 BACK VIEW 1. W all mount 2. Battery compartment 3. T able stand REMOTE SENSOR (THGR122N) GETTING ST ARTED 1 2 3 BAR608HGA lab test R2 1/17/04, 4:39 PM 4.
EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1. Wall mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) 1 2 1 2 3 4 BAR.
EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. T ABLE ST AND OR W ALL MOUNT Use the stand on the back of the product, or mount it on a wall with a nail.
EN 7 3. Set the channel. The switch is located in the battery compartment. 4. Place the sensor near the main unit. Press RESET on the sensor . Then, press and hold MEM and CHANNEL on the main unit to initiate signal sending between the sensor and the main unit.
EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure.
EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold DOWN for 2 seconds. Then, manually set the clock following the "Set Clock" instructions (below).
EN 10 If no button is pressed, the Alarm will automatically silence after 2 minutes. It will then sound again after 8 minutes. BAROMETER This product tracks barometric pressure changes over the past 24 hours to provide the weather forecast ( 13) and a trend line showing the direction of barometric change.
EN 11 NOTE TEMPERA TURE AND HUMIDITY This product can display current, minimum, and maximum temperatures and humidity percentage information collected by the remote sensors and main (indoor) unit. Outdoor data is collected and displayed every 40 seconds.
EN 12 When you press RESET , all settings will return to default value, and you will lose all stored information. SAFETY AND CARE Clean the product with a slightly damp cloth and alcohol- free, mild detergent. Avoid dropping the product or placing it in a high-traffic location.
EN 13 SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 142 x 63 x 158 mm (5.5 x 2.5 x 6.2 inches) W eight 366 g (12.96 ounces) with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm (3.
EN 14 RELA TIVE HUMIDITY Range 25% to 95% Resolution 1% Memory Minimum / maximum BAROMETER Unit mb/hPa or inHg Range 700 to 1050 mb (20.67 to 30.01 inHg) Resolution 1 mb (0.
EN 15 FCC ST A TEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
EN 16 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead.
© 2004 Oregon Scientific. All rights reserved. P/N.: 086-003312-012 BAR608HGA lab test back cover 12/29/03, 10:40 PM 1.
An important point after buying a device Oregon Scientific BAR608HGA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oregon Scientific BAR608HGA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oregon Scientific BAR608HGA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oregon Scientific BAR608HGA you will learn all the available features of the product, as well as information on its operation. The information that you get Oregon Scientific BAR608HGA will certainly help you make a decision on the purchase.
If you already are a holder of Oregon Scientific BAR608HGA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oregon Scientific BAR608HGA.
However, one of the most important roles played by the user manual is to help in solving problems with Oregon Scientific BAR608HGA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oregon Scientific BAR608HGA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
