Instruction/ maintenance manual of the product WS-7013U Oreck
Go to page of 16
WS-7013U Wi r eless 433 MHz T emperatur e Station Instruction Manual Register your product on the web at: WWW .ORECK.COM.
T ABLE OF CONTENTS T opic Page Inventory of Contents 2 Quick Setup 3-5 Detailed Setup Guide Battery Installation 5-7 Setting the T ime 7-8 Selecting Units of Measurement 8 Features Minimum and Maximum.
INVENTOR Y OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket (Figure 2) 3. (3) 1/2" Philips screws 4. One strip of double sided adhesive tape 5. Instruction Manual and W arranty Card 6.
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the r emote temperatur e sensor first then into the indoor temperature station.
Any walls the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Y our distance plus resistance should not exceed 80 feet in a straight line.
3. The hour will now be flashing. a. Press and release the " MIN/MAX " button until the correct hour is shown. Note: When in the 12h mode "PM" is displayed under the word "TIME" during PM hours. During the AM hours this area will be blank.
B. INDOOR TEMPERA TURE ST A TION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly . 1. Remove the battery cover on the backside. To do this, push the cover upward and pull it out.
5. The indoor temperature station should now show: "-:- -" in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’ s. II. TIME A. SETTING THE TIME 1. Press and hold the " SET " button for 5 seconds, "12h" will appear in the TIME LCD.
4. Press and release the " MIN/MAX " button to set the hour . 5. Press and release the " SET " button to move to the minute setting. 6. Press and release the " MIN/MAX " button to set the minutes. 7. Press and release the " SET " button to activate the clock.
IV . FEA TURES A. MINIMUM AND MAXIMUM TEMPERA TURES 1. Press and release the " MIN/MAX " button. "MIN" appears in the temperature LCDs and the recorded minimum temperatures are displayed. 2. Press and release the " MIN/MAX " button to toggle to the maximum temperatures.
before permanently mounting. A. REMOTE TEMPERA TURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor . 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. THE TEMPERA TURE ST A TION 1.
Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station.
responsive to ambient air currents because of the shielding effect of the display case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.
SPECIFICA TIONS T ransmitting 433MHz Frequency Measuring T emperatur es Indoor T emperature 32°F to 156.2°F with Station: Indoor 0.2°F resolution. (0°C to 69.0°C with 0.1°C resolution) Remote T emperature -21.8 °F to 156.2°F Sensor: Outdoor 0.
Remote T emperature 1.57" x 0.9" x 5.04" Sensor (40 x 23 x 128 mm) Battery life Approximately 1 year W ARRANTY INFORMA TION Oreck Corporation warrants the Indoor/Outdoor Clock and W eather Station (WS-7013U) free from defects in material and workmanship under normal, non-commercial use and service.
©2002 Oreck Holdings, LLC. All rights reserved..
An important point after buying a device Oreck WS-7013U (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oreck WS-7013U yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oreck WS-7013U - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oreck WS-7013U you will learn all the available features of the product, as well as information on its operation. The information that you get Oreck WS-7013U will certainly help you make a decision on the purchase.
If you already are a holder of Oreck WS-7013U, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oreck WS-7013U.
However, one of the most important roles played by the user manual is to help in solving problems with Oreck WS-7013U. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oreck WS-7013U along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
