Instruction/ maintenance manual of the product SKC-550C Onkyo
Go to page of 72
E n 7.1ch Home Theater System HT -SR800 AV Receiv er (HT -R550) Front Speak ers (SKF-550F) Center Speaker (SKC-550C) Surround Speak ers (SKM-550S) Surround Back Speak ers (SKB-550) Po wered Subwoofer (SKW -550) Instruction Manual Thank you for purchasing an Onkyo 7.
2 Important Safety Instructions 1. Read these instructions. 2. K eep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Speaker Precautions Placement • The speaker cabinets are made out of wood and are therefore sensitiv e to extreme temperatures and humidity , do not put them in locations subject to direct sunlight or in humid places, such as near an air condi- tioner , humidifier, bathroom, or kitchen.
5 Enjo ying Home Theater Y ou can use two sets of speakers with the A V receiv er: speak er set A and speak er set B . Speaker set A (included speakers) should be used in your main listening room for up to 7.1-channel playback. *While speaker set B is on, speaker set A is reduced to 5.
6 Pa ck ag e Contents Make sure you ha ve the follo wing items: * In catalogs and on packaging, the letter at the end of the product name indicates the color .
7 Features Amplifier • 7-channel amplifier • 110 watts per channel rms into 8 ohms, 2 channels driv en at 1 kHz, less than 0.9% total harmonic distor- tion (FTC rating) • WRA T (Wide Range Amp.
8 Connect the speakers and y our A V components to the A V receiver . ☞ page 19 OUT OUT CBL/SAT IN IN IN IN IN IN IN IN VCR/DVR IN DVD IN OUT COMPONENT VIDEO Y C B/ P B C R/ P R IN 1 IN 2 OUT ANTENN.
9 Contents Introduction Important Safety Instructions ....................2 Precautions ................................................. 3 Speaker Precautions ..................................4 Enjoying Home Theater ..............................5 Speaker Sets A and B .
10 Getting to Kno w the A V Receiver For detailed information, see the pages in parentheses. A ST ANDBY/ON button (36) Sets the A V receiv er to On or Standby . B ST ANDBY indicator (36) Lights up when the A V receiv er is on Standby and flashes while a signal is being receiv ed from the remote controller .
11 Getting to Know the A V Receiver —Continued J T ONE, [–], and [+] buttons (46) Used to adjust the bass and treble. K STEREO button (48) Selects the Stereo listening mode. L LISTENING MODE [ ]/[ ] buttons (48) Select the listening modes. M DISPLA Y button (43) Displays various information about the currently selected input source.
12 Getting to Know the A V Receiver —Continued A DIGIT AL IN OPTICAL 1, 2 and CO AXIAL 1, 2 These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and D VD players. B HDMI IN 1, 2, and OUT These jacks are for connecting HDMI-compatible components.
13 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
14 Remote Controller —Continued Including the A V receiv er, the remote controller can be used to control up to sev en different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the six REMO TE MODE buttons.
15 Remote Controller —Continued For detailed information, see the pages in parentheses. A ST ANDBY/ON button (36) Sets the A V receiv er to On or Standby . B INPUT SELECT OR buttons (42) Used to select the input sources. C MUL TI CH button (43) Selects the multichannel D VD input.
16 Remote Controller —Continued By default, the remote controller is set to control an Onkyo D VD player . A ST ANDBY/ON button Sets the D VD player to On or Standby . B Number buttons Used to enter title, chapter , and track numbers and times for locating specific points.
17 Remote Controller —Continued By default, the remote controller is set to control an Onkyo CD player . A ST ANDBY/ON button Sets the component to On or Standby . B Number buttons Used to enter track numbers and times for locating specific points on CD/MD players.
18 Speaker s For detailed information, see the pages in parentheses. A ST ANDBY/ON indicator Red: Subwoofer in standby mode Green: Subwoofer on W ith the Auto Standby function, the SKW -550 automatically turns on when an input signal is detected in Standby mode.
19 Connecting Y our Speakers Thanks to the A V receiv er’ s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring DTS and Dolby Digital.
20 Connecting Y our Speaker s —Continued Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of between 8 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high v olume lev els for a long period of time, the built-in amp pro- tection circuit may be activ ated.
21 Connecting Y our Speaker s —Continued The following illustration sho ws which speaker should be connected to each pair of terminals. The speakers can easily be mounted on a wall by using the attached wall brackets.
22 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiv er won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner .
23 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
24 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
25 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiv er.
26 Connecting Y our Components —Continued If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiv er to the A V receiver and use its tuner to listen to TV programs through the A V receiver (see pages 30 and 32).
27 Connecting Y our Components —Continued Connecting a D VD player Connection A V receiver Signal flow DVD pla yer Picture quality COMPONENT VIDEO D VD IN ⇐ Component video output Best D VD IN S .
28 Connecting Y our Components —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as DVD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiv er’ s multichannel DVD input.
29 Connecting Y our Components —Continued If you hav e an HDMI-compatible player, you can connect it to the A V receiver with an HDMI cable. Notes: • Audio and video signals receiv ed via the HDMI IN jacks are output only by the HDMI OUT .
30 Connecting Y our Components —Continued W ith this hookup, you can use your VCR’ s tuner to listen to your fav orite TV programs via the A V receiv er, useful if your TV has no audio outputs.
31 Connecting Y our Components —Continued Connecting a VCR or D VD Recorder f or Recording Connection A V receiver Signal flow VCR or D VD recorder Picture quality VCR/D VR OUT S ⇒ S-Video input .
32 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiver to listen to your f av orite TV programs via the A V receiv er, useful if your TV has no audio outputs.
33 Connecting Y our Components —Continued ■ CD Play er or T urntable (MM) with Built-in Phono Preamp •W ith connection , you can listen to and record audio from your CD player or turntable and listen via speaker set B. •T o connect the CD player digitally , use connection or .
34 Connecting Y our Components —Continued ■ RI Dock with video Connect your RI Dock’ s analog audio output jacks and S-V ideo output jack to the A V receiv er’ s CBL/SA T IN L/R jacks and CBL/SA T IN S jack. ■ RI Dock without video Connect your RI Dock’ s analog audio output jacks to the A V receiv er’ s T APE IN L/R jacks ( 1 ).
35 Connecting Y our Components —Continued W ith (Remote Interactive), you can use the follo wing special functions: ■ A uto P ower On/Standby When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source.
36 T urning On the A V Receiver MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE AUX CBL/SAT VCR/DVR DVD MULTI CH C D SETUP ENTER SETUP MI.
37 Fir st Time Setup This section explains the settings that you need to make before using the A V receiv er for the very first time. W ith the supplied speaker setup microphone, the Audyssey 2EQ/HTI.
38 First Time Setup —Continued Using A udyssey 2EQ/HTIB Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 60) will be set to “ Audyssey . ” •Y ou can cancel the automatic speaker setup at any point in this procedure simply by disconnecting the setup microphone.
39 First Time Setup —Continued Error Messa g es While the automatic speaker setup is in progress, one of the following error messages may appear: Ambient noise is too high This message appears if there’ s too much background noise and the measurements cannot be performed prop- erly .
40 First Time Setup —Continued If you connect a video component to HDMI IN 1 or 2, use this setting to assign that input to an input selector . HDMI Video Setup MUTING PREVIOUS MENU GUIDE TOP MENU S.
41 First Time Setup —Continued To enjoy Dolby Digital and DTS, you must connect your D VD player to the A V receiver digitally (coaxial or opti- cal). These are the default digital audio input assignments. Y ou can change the digital audio input assignments if necessary .
42 Pla ying Y our A V Components Basic A V Receiver Operation MASTER VOLUME VIDEO STANDBY TONE DISPLAY STEREO DIMMER MEMORY DIGITAL INPUT TUNING MODE AB SPEAKERS TUNER TAPE AUX CBL/SAT VCR/DVR DVD MUL.
43 Playing Y our A V Components —Continued The multichannel D VD input is for connecting a compo- nent with a 7.1-channel analog audio output, such as a D VD-Audio or SACD-capable D VD player , or an MPEG decoder . See page 28 for hookup information.
44 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations. ■ AM Frequency Step Setup (not North America) Y ou must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted.
45 Listening to the Radio —Continued ■ T uning into Stations by Frequenc y Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Y ou can store a combination of up to 40 of your favorite AM/FM radio stations as presets.
46 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the bass and treble for the front speakers, except when the Direct or Pure Audio (not North Amer- ican models) listening mode is selected.
47 Common Functions —Continued W ith the sleep timer, you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] b utton.
48 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 50. Selecting on the A V Receiver ■ [PURE A UDIO] button (not North American model) This button selects the Pure Audio listening mode.
49 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. : Only a vailable on 6.1/7.1-channel playback systems. Not a vailable while speak er set B is on. : Only a vailable on 7.
50 Using the Listening Modes —Continued The A V receiv er’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
51 Using the Listening Modes —Continued DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with D VDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.
52 Using the Listening Modes —Continued W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low volume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone.
53 Using the Listening Modes —Continued The Audio Adjust settings are explained belo w . Input Channel Settings ■ Multiplex This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
54 Using the Listening Modes —Continued T -D Listening Angle Setting ■ Lstn Angl (Listening Angle) W ith this setting, you can specify the angle of the front left and right speakers relati ve to the listening position. Processing for the Theater -Dimensional listening mode is based on this setting.
55 Recor ding This section explains ho w to record the selected input source to a component with recording capability , and how to record audio and video from dif ferent sources. Y ou can only record to a component that’ s connected to the T APE OUT or VCR/D VR OUT jacks.
56 Ad v anced Setup This section explains ho w to check the speaker settings and how to set them manually , which is useful if you change a speaker after performing the automatic speaker setup. Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 37).
57 Adv anced Setup —Continued Note: • These settings cannot be changed while headphones are connected, speaker set B is on, or the multichannel D VD input is being used. Crosso ver Frequency This setting only applies to the speakers that you speci- fied as Small in the “Speaker Configuration” on page 56.
58 Adv anced Setup —Continued Double Bass W ith the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left and right channels to the subwoofer .
59 Adv anced Setup —Continued Notes: • The Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Front distance. For e xample, if the Front distance is set to 20 ft. (6 m), the Center and Subwoofer distances can be set between 15 and 25 ft.
60 Adv anced Setup —Continued Equalizer Settings Here you can adjust the tone of individual speak ers. T o set the volume of indi vidual speakers, see page 59. Notes: • The front, center , surround, and surround back speak- ers can be adjusted at 80 Hz, 250 Hz, 800 Hz, 2500 Hz, and 8000 Hz.
61 Adv anced Setup —Continued The following table sho ws the display indicator for each digital signal format. Normally , the A V receiver detects the signal format auto- matically .
62 Contr olling Other Components Y ou can use the A V recei ver’ s remote controller (RC-681M) to control your other A V components, including those made by other manufacturers. This sec- tion explains ho w to enter the necessary remote control code for the component that you want to control (e.
63 Controlling Other Components —Continued Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allows you to control components that are out of view , in a rack, for example.
64 Controlling Other Components —Continued To control another component, point the r emote controller at it and use the buttons explained below . (Y ou must select the appropriate r emote control mode first.) W ith some A V components, certain buttons may not work as expected, and some may not work at all.
65 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all outlet, wait 5 seconds or more, then plug it in again.
66 Tr oubleshooting —Continued The center speaker produces no sound • When the Stereo or Mono listening mode is selected, the center speaker produces no sound (page 50). • Make sure the speakers are configured correctly (page 56). The surround bac k speakers produce no sound • While speaker set B is on, speaker set A is reduced to 5.
67 Tr oubleshooting —Continued Reception is noisy , stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear • Relocate your antenna. •M ove the A V recei ver a way from your TV or com- puter . • Listen to the station in mono (page 44).
68 Tr oubleshooting —Continued The A V receiver contains a microcomputer f or signal processing and control functions. In very rare situa- tions, se vere interf erence, noise from an e xter nal source, or static electricity may cause it to loc kup.
69 Specifications Amplifier Section Video Section T uner Section General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs Specifications and features are subject to change without notice.
70 Specifications —Continued 7.1ch Home Theater Speaker Pac kage ■ Po wered Subwoofer (SKW -550) ■ Front Speaker (SKF-550F) ■ Center Speaker (SKC-550C) ■ Surround Speaker (SKM-550S/SKB-550) Specifications and appearance are subject to change without prior notice.
71 Memo HT-SR800_En.book Page 71 Tuesday, January 30, 2007 11:09 AM.
72 SN 29344416 I0702-1 (C) Copyright 2007 ONKY O CORPORA TION Japan. All rights reser ved. http://www.onky o.com/ HOMEP AGE Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.
An important point after buying a device Onkyo SKC-550C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Onkyo SKC-550C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Onkyo SKC-550C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Onkyo SKC-550C you will learn all the available features of the product, as well as information on its operation. The information that you get Onkyo SKC-550C will certainly help you make a decision on the purchase.
If you already are a holder of Onkyo SKC-550C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Onkyo SKC-550C.
However, one of the most important roles played by the user manual is to help in solving problems with Onkyo SKC-550C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Onkyo SKC-550C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
