Instruction/ maintenance manual of the product LV-1201 Omega Vehicle Security
Go to page of 8
BOOT 15 AMP CAPACITY MICROSWIT SINGLE POLE DOUBLE THROW ELIMINATES RELAYS, ALLOWS DIRECT CONTROL OF PUMP MOTORS SOLENOID VALVES, HEATERS, ETC. BUNA N FILTER 1 WATER, OIL RESISTANT STRAIN RELIEF ELECTRICAL CABLE CONNECTOR 7 HOLLOW POLYP ROPYLENE FLOAT FLOAT SHAFT _ ILV1203l ” TO 1” RYTON R-4 BUSHING X (LV.
GREY) SUPPLIED WITH THE LV-1200 SERIES CAN BE CRACKED IF THE CENTER BODY IS FIRST TIGHTENED INTO THE BUSHING. CRACKING PROBABILITY IS REDUCED IF THE BUSHING IS FIRST TIGHTENED INTO THE PIPE OR TANK FITTING AND THEN THE CENTER BODY TIGHTENED INTO THE BUSHING.
r-- FLOAT SHAFT OR DRAG DISK ARM (E) (D) WARNING LV-1200 Series are NOT explosion-proof devices. 3 .‘ -SEALSHAFT 1 &i (C) DIAPHRAGM SEAL (B) DIAPHRAM WASHER 1 FEEDTHRU SHAFT OR SWITCH ACTUATING ARM I IS ASSEMBLED. FILTER BOOT (F) (El IS UN- THREADED AND A NEW SHAFT DISK ARM (E), DURING CHANGE OF FLOAT OR DRAG DISK.
“. Slip on terminals are supplied with each switch. Remove them from the switch terminals and crimp on or solder to the electrical leads. Feed the electrical cable through the gland nut, grommet and switch cover as shown below. n Apply slip on terminals to appropriate contacts of the microswitch.
MICROSWITCH LINE Microswitch actuation point may be monitored by an audible click or with an OHM meter before connecting the line power to the terminal strip or by monitoring the voltage supplied to the load through the microswitch.
>,,” FLEXIBLE CONDUIT LV-1201 AND LV-1202 PARTS LIST DIAGRAM 6 ‘ F’ COVER TO SUIT CUSTOMER SUPPLIED FITTING FOR 10399~16. FLOAT SHAFT + % - IAI I INORYLI IF FLOAT IS TO BE REMOVED FROM ASSEMBLY, THE FLOAT SHAFT MUST BE GRIPPED BY PLIERS OR IN A VICE TO PREVENT UNTHREADING FROM THE SEAL SHAFT -178.
%” L I J LV-1203 PARTS LIST DIAGRAM ;;;PXq;;;J~;lN~FOR 1 1 1 ‘ F’ COVER TO SUIT CUSTOMER (Al I I I StAL SHAFT k”“ M tA ” lNCI - -_.. __^.. .^...^ UNTHRr OR IN A VICE TO PREVENT an-r MUST BE GRIPPED BY PLIERS ~1v-1 A=+LI.IDLI, -_..-.._- FROM .
A.lNWWWJl va3wa sluem~ sgl ly eq 01 eel, ,o sloe,ep u! s(e!mew d!qsuewyom pus pus 01 eA!B h~ol~e,syas e+ues JO, po!led e 40 pi sqwotu uoy ,o elep ‘ essqlmd v~)3wO AlueueM ue sppe leuo!l!ppe euo (L) .
An important point after buying a device Omega Vehicle Security LV-1201 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Omega Vehicle Security LV-1201 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Omega Vehicle Security LV-1201 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Omega Vehicle Security LV-1201 you will learn all the available features of the product, as well as information on its operation. The information that you get Omega Vehicle Security LV-1201 will certainly help you make a decision on the purchase.
If you already are a holder of Omega Vehicle Security LV-1201, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Omega Vehicle Security LV-1201.
However, one of the most important roles played by the user manual is to help in solving problems with Omega Vehicle Security LV-1201. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Omega Vehicle Security LV-1201 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
