Instruction/ maintenance manual of the product TECHCON SYSTEMS TS250 OK International
Go to page of 17
Techcon Systems TS250 / 255 Precision Dispensers User Guide English, German, Fre nch, Italian and Spanis h version Copyright © OK Inte rnational TS250 / 255 Präzsions-Dosiergeräte Benutzerhandbuch .
3 being sucked back into th e unit. Also do not over fill the barrel and to lay the barrel on its side • Do not smoke or use open flame when fl ammable mate rials ar e being dispensed • This equip.
5 5 CONNECTING THE UNIT CAUTION: A 5-micron filter (TSD800-6), not incl uded, must be installe d with the unit to ensure proper air filtration. Figure 2.0 6 SETUP INSTRUCTIONS Refer to Figure 1.0 6.1 Manual Dispense Cycle Setting: 1. Turn on the unit by pressing the Power button (1) 2.
7 8 MAINTENANCE The dispenser is designed and built to be relatively maintena nce free. To assure trouble free operation, the follow ing recommendations should be followed: 1. Make certain air supply is clean and dry. 2. Avoid turning barrels upside down or laying barrel so that material may run through air line to internal components.
3 • Das dosierte Medium kann giftig und/oder gefährlich sein. Weitere Einzelheiten bezüglich ordnungsgemäßer Handhabung und Sicherheitsvorkehrungen finden Si e im Sicherheitsdatenblatt.
5 4 HAUPTKOMPONENTEN Abb. 1.0 Positionen Beschreibung 1 Ein-/Aus-Taste 2 Modustaste 3 Nullstellung Zykluszähler 4 Display 5 Druckluftmesser 6 Druckluftregler 7 Ausgang für gepulste Luft 8 Einstellun.
7 3. Wiederhole Schritt 3 bis 6 in Abschnitt 6.1. 4. Starten Sie den zeitg esteuerten Do sierzyklus mit dem Fußschalter. 6.3 Zyklenzäh ler Der Zyklenzähler registriert di e Anzahl der aktivierten au tomatischen Dosierzyklen. Es können bis zu 65.535 Zyklen aufgezeichn et werden.
2 SOMMAIRE P Pages 2 Sécurité……………………………………………………….…………2 - 3 2 Définition des symboles…………………………………………………3 3 .
4 4 FONCTIONNALITÉS Figure 1.0 Élément Description 1 Bouton Marche 2 Bouton Mode 3 Bouton de reinitialisation 4 Écran 5 Manomètre 6 Régulateur de répression d'air 7 Sortie d'air puls.
6 2. Tournez le bouton de contrôle du temp s (9) pour régler le temps de dosage désiré. 3. Répétez les étapes 3 a 6 de la section 6.1. 4. Appuyez sur la pédale de commande pour déclencher le cycle de dosage temporisé. 6.3 Compteur de cycle Le compteur de cycle enregistre le nombre de cycles de dosage automatique effectués.
2 INDICE Pagina 1 Sicurezza....... ........... ............ ........... ...................... ........... ..…………2 - 3 2 Significato dei simboli..... .......... ........... ............ ........... ......…………3 3 Specifiche.. ..........
4 3 SPECIFICHE Misura 152mm X 165mm X 178mm (6” X 6.5” X 7.0”) Peso 1,2kg (2,6 libre) Tensione d’al imentazione 24 VCC con trasformatore in dot azione Potenza nominale 10 W Alimentazione aria 6.9 bar max. Grado d’inquinamento II Categoria d’installazione I Utilizzo al chiuso Altitudine fino a 2.
6 5 ALLACCIAMENTO DELL’APPARECCHIO ATTENZIONE: occorre installare un filtro riduttore 5 micron (TSD800-6), Non incluso, all’ingresso dell’unità per assi curare un’adeguata fi ltrazione dell’aria. Se è richiesta la funzione antisgocciolo, l’ar ia di ingresso deve a vere una pressio ne Costante regolabile da 0-6.
8 8 MANUTENZIONE Il dosatore è concepito e costruito in m odo tale per cui non richiede pressoché alcuna manutenzione. Per garantire un funz ionamento esente d a guasti, si consiglia di seguire le raccomandazi oni riportate di seguito. 1 Accertarsi che l’aria di alimentazione sia pul ita e secca.
3 • Si no se utiliza un pistón con el b arril, debe instalarse un filtro en línea (881- 000-000), No Incluido , en la cab eza receptora pa ra impedir que los líquidos sean succionados nuevamente a la unidad.
5 5 CONEXIÓN DE LA UNIDAD PRECAUCIÓN: Debe instalarse un filtro de 5 micras (TSD800-6), No In cluido, con la unidad para garantizar un filtrado correcto del aire. Figura 2.0 6 INSTRUCCIONES DE INSTALACIÓN Consulte la Figura 1.0 6.1 Configuración del ciclo de dosificación manual 1.
7 8 MANTENIMIENTO El dosificador está diseñado y fabri cado para estar relativamente li bre de mantenimiento. Para garantizar una ope ración satisfactoria, deben seguirse las recomendaciones detalladas a continuación: 1 Asegúrese que el suministro de aire esté limpio y seco.
An important point after buying a device OK International TECHCON SYSTEMS TS250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought OK International TECHCON SYSTEMS TS250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data OK International TECHCON SYSTEMS TS250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, OK International TECHCON SYSTEMS TS250 you will learn all the available features of the product, as well as information on its operation. The information that you get OK International TECHCON SYSTEMS TS250 will certainly help you make a decision on the purchase.
If you already are a holder of OK International TECHCON SYSTEMS TS250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime OK International TECHCON SYSTEMS TS250.
However, one of the most important roles played by the user manual is to help in solving problems with OK International TECHCON SYSTEMS TS250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device OK International TECHCON SYSTEMS TS250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
