Instruction/ maintenance manual of the product OP14 Oce
Go to page of 16
1.1.1. Océ OP14 Printing System Set-up O p erations Guide Education Services Océ Operations Guide E n g l i s h v e r s i o n.
i T rademark Information • PRESCRIBE is a registered trademark of K yocera Corporation. • PRESCRIBE 2e and KPDL2 are trademarks of Kyocera Corporation. • MS-DOS, Windows and Windows NT are trademarks of Microsoft Corporation. • PCL and PJL are registered trademarks of Hewlett-P ackard Compan y .
ii IBM PROGRAM LICENSE A GREEMENT THE DEVICE Y OU HA VE PURCHASED CONT AINS ONE OR MORE SOFTW ARE PROGRAMS (“PR OGRAMS”) WHICH BELONG T O INTERNA TIONAL BUSINESS MA CHINES CORPORA TION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTW ARE IS BEING LICENSED TO Y OU BY IBM.
iii T ypeface T rademar k Acknowledgement All resident fonts in this printer are licensed from Agf a Cor poration. Helvetica, P alatino and Times are registered trademarks of Linotype-Hell A G. ITC A vant Garde Gothic , ITC Bookman, ITC ZapfChancer y and ITC Zapf Dingbats are registered trademarks of Inter national T ype-f ace Cor poration.
iv About this Instruction Handbook This Instruction Handbook <Set-up Edition> is meant to be read when the Printer Board is installed in your copier and the copier is to be used mainly as a local printer . It contains e xplanations on set-up procedures for using the copier as a printer .
v Getting connected When connecting the printer directly to your computer (with a parallel cable) ... Parallel cable 1 Connecting the printer directly to your computer with a parallel cable ...................................... Page 3 2 Installing the printer driver into your computer .
T ab le of contents 1. Preparations ............................................................................................................. 1 1-1 Accessories .......................................................................................
1 1. Preparations 1-1 Accessories • 1 CD-ROM • This Instruction Handbook 1-2 Required items • Parallel cable 1-3 Name of par ts (main body) 1 Parallel interface connector Connect a bi-directional parallel cable here. 2 Memory Card slot Insert the optional Memory Card here.
2 1. Preparations 1-4 Name of parts (operation panel) Inch specifications 129% 200% 50% 100% 78% Start Stop/ Reset Memory Over f low/ Data Error Add Toner Paper Select AutoExp .
3 2. Set-up 2-1 Connecting the printer cable CAUTION: AL W A YS tur n the main switch to the printer OFF (O) BEFORE connecting the printer cable. T urn the main switch located on the right side of the printer OFF (O) and then turn the power off to your computer as well.
4 2. Set-up 2-3 Netw ork (TCP/IP) settings When the optional Network Card is installed and this machine is to be used as a network printer, it is necessary to set the corresponding IP address f or the pr inter . Notes • The IP address that should be registered here will diff er depending upon your network environment.
5 3. T r oubleshooting 3-1 Canceling printing Perform the following procedure when you want to stop printing or you want to clear data. IMPORT ANT! • By performing this operation you will be canceling ALL print jobs that are currently w aiting in the pr inter ’ s memor y to be printed.
6 3. T roub leshooting 3-2 When an err or code or error messages appear s… If an error code appear on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding procedure.
7 3. T roubleshooting Error code E60 E70 E71 E72 E73 E80 E82 E83 EF1 EF2 Procedure A read- or write-error has occurred on the RAM disk. Press the Star t [GO] key to er ase the error indication. A read- or write-error has occurred in the Memory Card. Press the Start [GO] key to erase the error indication.
8 3. T roub leshooting 3-3 Basic tr oubleshooting chart If you e xperience trouble while you are using this machine as a printer , ref er to the table below to perf or m minor adjustments. If troub le persists, contact your service representative or an authoriz ed ser vice center.
9 4. Specifications CPU ................................................................... PowerPC 405 (200MHz) Printing Speed ................................................... 15, 18 ppm copier : 18 pages/min (A4 [8 1/2" x 11"]) Printing Resolution .
An important point after buying a device Oce OP14 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Oce OP14 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Oce OP14 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Oce OP14 you will learn all the available features of the product, as well as information on its operation. The information that you get Oce OP14 will certainly help you make a decision on the purchase.
If you already are a holder of Oce OP14, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Oce OP14.
However, one of the most important roles played by the user manual is to help in solving problems with Oce OP14. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Oce OP14 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
