Instruction/ maintenance manual of the product TT500 Numark Industries
Go to page of 16
CONTENTS Safety Precautions Setup & Installation Controls Cable Setup Platter Setup Inter chan g in g Tonearm Tubes T one Arm S etup Cartrid g e Setup Important Notes & Operation Spec ificat i.
Thank you for purchasing this Numa rk product. Please read thes e operating inst ructions so you wi ll know how to operate t his equipm ent properly. After you have finished reading t hese instructions, keep the m for future reference. WARNING: TO PREVENT FIRE OR SH OCK HAZARD, DO NOT EXPOSE THIS APPLI ANCE TO RAIN OR MOISTURE.
POWER-CORD PROTECTION Power-suppl y cords should be rout ed so that they are n ot likely to be wal ked on or pinched by items placed upon or against the m, paying particular attention to cords a t plugs, convenienc e receptacles, and t he point where they exit from the produ ct.
SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be se tup in a variety of different ways depe nding on your mixing style.
CONTROLS General Controls 1. Power Button This button turns on the turntable when pressed. It illuminates blue when the turntable i s switched on. 2. Platter This turntable has a special edge design that has bee n optimized for "dragged" platter slow downs.
CONTROLS c ontinued 9. Pitch Fader This s lide cont rol a llow s the pitch o f th e pl aybac k sou rce t o be changed. In the ce nter position the pitch is at 0%. Moving the fader knob closer to you will increase the pitch. The Pi tch Slider is enclosed in an Interchangeable/Replaceabl e Cartridge.
CONTROLS continued Bottom Parts 20. Adjust able Rubber Dampeni ng Feet When all of the fe et of the turntable ar e completely tig htened, the top flat surface o f the turntable w ill be at 85mm. Unsc rewing these feet rai ses the turnta ble up to compens ate for unlevel ed surfaces.
CABLE SETUP This turntable is sh ipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the prope r setting! Making the power and audio connections: 1.
PLATTER SETUP WARNING: Incorre ct Platter setup can l ead to poor turn table performance, platte r instability, or permanent motor damage. 1. Start by inspecti ng the bottom of t he aluminum plat ter to check that bot h locking pins have r ubber fitting s on them.
INTERCHANGING TONEARM TUBES WARNING : An incomplete under standing of this procedure could le ad to permanent da mage to the headshe ll, your records, or th e tonearm assembly. NOTICE : Interchanging tonear m tubes unnecessarily m ay shorten the life of the tone arm tubes and/or tonearm component s.
TONE ARM SETUP A properly adjusted tone arm and cartri dge setup will mini mize vinyl recor d wear and optimize th e performance of the turntable. Follo w these simple steps fo r setting the tone arm .
CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that c omes with this tur ntable should be pre installed on the he ad shell. If it is n't, please follow the below instruct ions for installing a cartridge onto the head shell. 1. Position the head shell an d the cartridge so that th e four connector pins are visible.
OTHER IMPORTANT NOTES Please read these prec autionary notes to in sure a comple te understanding and long life of th is DJ turntable. 1. Unneces sarily remov ing the plat ter may cause d amage to the ma gnet mounti ng structu re, the motor or th e platter resulting in undesired pe rformance.
SPECIFICATIONS Turntable: Torque (transient) : 4.5kgf.cm Torque (stab le): 3.5kgf.cm Motor: Brushless DC motor Brake: Elec tronic braking system Platter: Dampened aluminu m diecast, low frictio n design Pitch: +/-8%, 10%, 25%, 50% Speeds: 33 1/3RPM, 45RP M, 78RPM Wow/flutter: <0.
T ROUBLE SHOOT ING PAGE 14 Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. T he Turntable is not co nnected to a device with a PHON O preamp. Connect the device to a preamp DJ mixer or an AV rece iver that has an input labeled PHO NO.
(1) Turntable w /Straigh t Tonearm (1) Anti-Drag A luminum P latte r (1) S -Shaped Tonea rm Tube (1) S -Tube Tone arm Weigh t (1) IEC Power C able (1) Service To o l (1) RCA Cor d (1) Slipma t INSIDE .
An important point after buying a device Numark Industries TT500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Numark Industries TT500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Numark Industries TT500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Numark Industries TT500 you will learn all the available features of the product, as well as information on its operation. The information that you get Numark Industries TT500 will certainly help you make a decision on the purchase.
If you already are a holder of Numark Industries TT500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Numark Industries TT500.
However, one of the most important roles played by the user manual is to help in solving problems with Numark Industries TT500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Numark Industries TT500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center