Instruction/ maintenance manual of the product CalPilot 4.0 Nortel Networks
Go to page of 176
CallPilot R elease 4 . 0 Document Number: 555-71 01 -220 Document V ersion : St andard 1. 03 July 2006 2 01i S erver Har dw ar e Ins t allation.
Standard 1.03 2 CallPil ot Copyright © 2006 Nortel Networks. All Rights Reserved. The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document ar e believed to be accurat e and reliabl e, but are pre sented without express or implied warranty.
July 2006 201i Server Hardware Installation 3 CRYSTAL REPORTS is a trademark of Seagate Software Inc. EUDORA and QUALCOMM are trademarks of Qualc omm, Inc.
Standard 1.03 4 CallPil ot SONY is a trademark of Sony Corporation. SYBASE is a trademark of Sybase, Inc. TEAC is a trademark of TEAC Corporation. US ROBOTICS, the US ROBOTICS logo, and SPORTSTER are trademarks of US Robotics. WINZIP is a trademark of Nico Mark Computing, Inc.
201i Server Hardware Installation 5 Publication history Jul y 2006 Standard 1.03 of 201i Server Har dwar e Installation is released for CallPilot 4.0 general a v ailability . April 2006 Standard 1.02 of 201i Server Har dwar e Installation is released for CallPilot 4.
6 CallPil ot Publication history Standard 1.03 . Fundamentals CallPilot Fundamentals Guide (555-7101-010) Planning and Engineering Data Networking for Voice over IP Guide (553-3001-160) Network Planni.
201i Server Hardware Installation 7 Task List Preparing for installation .................................. .................. 33 To unpack t he 201i serve r ............... ................. ................ ............... 39 Installing the 201i server in a large Meridian 1 system .
Task List Standard 1.03 8 CallPil ot To connect the CD-ROM and tape d rives to the 20 1i server (Option 11C Mini) ................... ................ ................ ................ ....... 147 To connect the CD-ROM and tape d rives to the 20 1i server (Succession 10 00).
201i Server Hardware Installation 9 Contents 1 How to get help 11 2 About the 201i server 13 201i server description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Network connectivity . . . . . . . . . . . . . . . .
Contents Standard 1.03 10 CallPil ot 6 Installing the 201i server in the Succession 1000 system 93 Succession 1000 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Removing the Media Gateway or Media Gatew ay Expansion cover .
201i Server Hardware Installation 11 Chapter 1 Ho w to get help This section explains ho w to get help for Nortel prod ucts and services. Getting Help from the Nor tel W eb site The best way to get technical supp ort fo r Nortel products is from the Nortel T echnical Support W eb site: http://www .
How to get help Standard 1.03 12 CallPil ot Outside North America, go to the follo wing W eb site to obtain the phone number for your region: http://www .
201i Server Hardware Installation 13 Chapter 2 About the 201i server In this chapter 201i server description 14 Network connectivity 22 P e ripheral conn ectivity 29.
About the 201i server Standard 1.03 14 CallPil ot 201i server description Introduction The 201i server is a fle xible multimedia telephony serv er designed to integrate with Nortel Meridian 1 * and Succession * 1000 products. The 201i serv er occupies two slots of a Meridian 1 shelf or Succession 1000 Media Gate w ay or Media Gate way Expans ion.
July 2006 About the 201i server 201i Server Hardware Installation 15 T wo Ethernet controllers on th e 201i server motherboard pro vide Ethernet capability . These controllers provide th e network interfaces for both the embedded LAN (ELAN) and customer LAN (CLAN).
About the 201i server Standard 1.03 16 CallPil ot The follo wing diagram sho ws the 201i server components:. Heat sink Hard drive power cab le Hard drive data cable Secondary backplane connector pin Secondary backplane connector 3.
July 2006 About the 201i server 201i Server Hardware Installation 17 F aceplate The follo wing diagram sho ws the 201i server f aceplate. The faceplate provides LEDs, MPC card slots, and connectors fo.
About the 201i server Standard 1.03 18 CallPil ot The follo wing table describes each faceplate feature: Faceplate feature Description Mouse connec tor The mouse c onnector is a stan dard PS/2 connec tor and is hot-pluggable.
July 2006 About the 201i server 201i Server Hardware Installation 19 MPC card status LEDs (continued) On, then off: The MPC card has been successfully po wered do wn.
About the 201i server Standard 1.03 20 CallPil ot Network and driv e acti vity LEDs (labeled as E, C, I, and S) The E and C LEDs indicate the presence of network acti vity for both the ELAN and CLAN interf aces (respecti v ely). When the y are lit, they indicate that the interfac es are prop erly attached to th eir respecti v e hubs.
July 2006 About the 201i server 201i Server Hardware Installation 21 En vironmental specifications T emperatures Relative humidity Recommended temperature 15 ° C (59 ° F) to 30 ° C (86 ° F) Absolu.
About the 201i server Standard 1.03 22 CallPil ot Netw ork connectivity Introduction This section sho ws ho w CallPilot and the Meridian 1 or Succession 10 00 system are inte grated into your network. It also describes what is required in the network for correct CallPilot operation.
July 2006 About the 201i server 201i Server Hardware Installation 23 G101631 T elephony LAN/Customer LAN (10/100BaseT or 100BaseT) Web-enab led administrativ e PC Web-enab led administrativ e PC Deskt.
About the 201i server Standard 1.03 24 CallPil ot Sample netw ork setup: Succession 1000 The following diagram sho ws an ex ample of how the 201i server can be integrated with the Succession 1000 syst.
July 2006 About the 201i server 201i Server Hardware Installation 25 In the illustration on page 24, the telephon y LAN (TLAN) provides IP connecti vity between the Succession 10 00 system and the i2004 Internet phonesets.
About the 201i server Standard 1.03 26 CallPil ot Netw ork requirements Appropriate network ing equipment must be a v ailabl e for both the CLAN and ELAN. The CLAN and ELAN must be proper ly conf igured for correct CallPilot operation. T o ensure correct conf iguration, Nortel recommends th at you consult a network specialist.
July 2006 About the 201i server 201i Server Hardware Installation 27 The follo wing table identifies the purpose of each connector on the NTRH0912 1 multi I/O cable.
About the 201i server Standard 1.03 28 CallPil ot RS-232 COM1 (male DB-9) This connector pro vides the connection to an external modem. The mod em allo ws administrators an d technical support personne l to administer the 201i server from a remote location.
July 2006 About the 201i server 201i Server Hardware Installation 29 P eripheral connectivity Introduction Peripheral equipment is attached to th e 201i server on the serv er faceplate.
About the 201i server Standard 1.03 30 CallPil ot MPC-8 car d The MPC-8 card looks like a T ype II PC card, and supports the multimedia telephony services on the 201i serv er . Four specially-designed card slots are a vai lable for the MPC-8. All are locat ed on the 201i server faceplate.
July 2006 About the 201i server 201i Server Hardware Installation 31 Note: The CD-R OM dri ve is not hot-pluggable. Y ou must power of f the server to connect or disconnect the dri v e. T ape drive (NTRH9038) An external SCSI tape dri ve is used to back up and restore data.
About the 201i server Standard 1.03 32 CallPil ot Note: The mouse connector on th e 201i facep late is a PS/2 co nnector . If you plan to use a USB mouse with USB-to-PS/2 conv erter , you must also use the Nortel-supplied 101 mm (4-in) PS/2 e xtension cable (A0855616).
201i Server Hardware Installation 33 Chapter 3 Preparing f or installation In this chapter Installation ov er view 34 Unpacking and inspe cting the 201 i ser ver 39 Switch and networ k requireme nts 4.
Preparing for installati on Standard 1.03 34 CallPil ot Installation o verview Introduction This section provides a high-le vel o ve rvie w of the requirements and procedure for installing the 201i server . For a list o f CallPilot document ation, see the document map on page 6.
July 2006 Preparing for in stallation 201i Server Hardware Installation 35 Installation chec klist The following checklist identi fies the step s required to install the 201i serv er and peripheral de vices. For more de tails, see Chapter 8, “Connecting peripheral de vices to the 201i serv er .
Preparing for installati on Standard 1.03 36 CallPil ot 2 Familiarize yourself with the “Switch and network requirements” on page 42 of this guide.
July 2006 Preparing for in stallation 201i Server Hardware Installation 37 6 Set the follo wing: SCSI IDs on the CD-R OM and tape drives (see pages 124 and 126) DIP switches on the CD-R OM dri.
Preparing for installati on Standard 1.03 38 CallPil ot 9 Connect the 201i serv er and de vices as follo w s: Connect the monitor , keyboa rd, and mouse to the 201i server f aceplate (see page 140). ❒ Connect the CD-R OM and tape dri ves to the intermediat e SCSI cable (see p age 142).
July 2006 Preparing for in stallation 201i Server Hardware Installation 39 Unpac king and inspecting the 201i server Introduction This section describes ho w to: unpack the 201i server and peripherals inspect the 201i serv er for damage It also describes what to do if you de termine that the 201i server is f aulty .
Preparing for installati on Standard 1.03 40 CallPil ot T o inspect the 201i ser ver for shipping damage Before proceeding with the installation, visually inspect the 201i serv er for any damag e that might ha ve occurred during shipping.
July 2006 Preparing for in stallation 201i Server Hardware Installation 41 What’ s next? Re vie w the “Switch and network requir ements” on page 42.
Preparing for installati on Standard 1.03 42 CallPil ot Switch and netw ork requirements Introduction The information in this section will help you plan your 201i serv er installation. Meridian 1 or Succession 1000 slot requirements The 201i server occupies physical and electrical slots.
July 2006 Preparing for in stallation 201i Server Hardware Installation 43 Meridian 1 I/O panel connections On large Meridian 1 systems (such as Option 51C), the 201i serv er requires two co nnections from the slot s to the I/O panel on the rear of the switch, as follo ws: One connection is for the multi I/O cable.
Preparing for installati on Standard 1.03 44 CallPil ot If the LAN is to be networ ked with the 201i serv er , you need a network specialist to ensure proper conf iguration. What’ s next? Install the 201i serv er in the Meridian 1 switch or Succession 1000 system.
201i Server Hardware Installation 45 Chapter 4 Installing the 201i server in a large Meridian 1 system In this chapter Overview 46 Repositioning the secondary backplane conn ector 48 Installing the 20.
Installing the 201i server in a large Meridian 1 system Standard 1.03 46 CallPil ot Overview Introduction This section describes ho w to install the 201i server in a Meridian 1 switch.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 47 Bac kplane (tip and ring) cable The backplan e (tip and ring) cable supplied with the 201i serv er (NTRH3501) provides 100Base-T Ethernet CLAN operation.
Installing the 201i server in a large Meridian 1 system Standard 1.03 48 CallPil ot Repositioning the secondary backplane connector Introduction The secondary backplane (DS30X) conn ector on the 201i server conn ects the server to the second slot on the shelf, thereby pro viding access to the vo ice channe ls pro vided by that slot.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 49 Secondary backplane con nector description The secondary backplane connector is attached to the ba ckplane edge of the 201i server .
Installing the 201i server in a large Meridian 1 system Standard 1.03 50 CallPil ot Required equipment T o mov e the secondary backplane c onnector , you need a Phillips No. 1 scre wdri ver . A pair of needle-nosed pliers can also be helpful for removing the pin connector .
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 51 See the following diagram: 5 Replace the pin connector so the pin s protrude through both connectors . Ensure that t he connectors ar e correctly a ligned as sho wn in the di agra m below .
Installing the 201i server in a large Meridian 1 system Standard 1.03 52 CallPil ot G101442 A B.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 53 6 Gently pres s the pin co nnector into the sock et until it is fully seated. 7 Remov e the ye llow b ackplan e warning label from the top lock latch on the 201i server .
Installing the 201i server in a large Meridian 1 system Standard 1.03 54 CallPil ot Installing the 201i server in the large Meridian 1 s witch Introduction The 201i serv er occupies two slots. Y ou can install the 201i serv er in slots 0 through 14. Ensure that both slots ha ve electrical backplane connecti vity .
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 55 What’ s next? Continue with “Remo ving the backplane (tip and ring) cabl es” on page 56.
Installing the 201i server in a large Meridian 1 system Standard 1.03 56 CallPil ot Remo ving the bac kplane (tip and ring) cables Introduction Y ou must remove the Meridian 1 backpl ane (tip and ring.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 57 T o remove the bac kplane cables 1 Remov e the I/O p anel cover from the rear of the Mer idian 1 switch. 2 Remov e the protective plate from the rear of the Meri dian 1 s witch.
Installing the 201i server in a large Meridian 1 system Standard 1.03 58 CallPil ot Remov e the ti e wraps where applicab le to free the ca ble . c. Remov e the conn ector , I/O filter assemb ly , and all mountin g hardware from the insid e of the I/ O panel so the slot is comp letely vacated.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 59 The f ollo wing diagr am shows an e xam ple using slots 3 and 4: What’ s next? Continue with “Installing the NTRH35 01 backplane cable” on page 6 0.
Installing the 201i server in a large Meridian 1 system Standard 1.03 60 CallPil ot Installing the NTRH3501 bac kplane cab le Introduction Y ou must connect the backplane (tip and ring) cable supplied with the 201i server (NTRH3501) for 100Base-T Ethernet CLAN operation.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 61 Bef ore y ou begin Before you can install the NTRH 3501 cable, you must remov e the e xisting backplane cable from the back of the switch. See “Removing the backplane (tip and ring) cables” on page 5 6.
Installing the 201i server in a large Meridian 1 system Standard 1.03 62 CallPil ot See the following diagram: What’ s next? Continue with “Installing the SCSI cables for Meridian 1” o n page 63.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 63 Installing the SCSI cables f or Meridian 1 Introduction Before you can connect a CD-R OM or tap e dri ve to the 201i server , you must install the SCSI cables.
Installing the 201i server in a large Meridian 1 system Standard 1.03 64 CallPil ot The connec tor on th e intermediate SCSI cable th at attaches to the 201i server f aceplate is a lo w-profile right-angle connector . This allows the cable to be attached with the Meridian 1 cabinet cov er on.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 65 In this diagram, the CD-R OM driv e is the first de vice. The tape dri ve is the last de vice. Note: Alternate SCSI de vice connection s cenarios are supported, but are not depicted in this guide.
Installing the 201i server in a large Meridian 1 system Standard 1.03 66 CallPil ot T o install the SCSI cables f or Meridian 1 1 Thread the SCSI connector end of the NTRH1408 cab le from the front of the Meridian 1 along the bot tom of the shelf to either the left or the right access channel.
July 2006 Installing t he 201i server in a large Meridian 1 system 201i Server Hardware Installation 67 See the following diagram: Note: The bac kplane co nnectors f or the right slot are not required and, therefore, are left v acant. 6 Thread the NTRH1410 cab le through the shelves belo w and out th rough the bottom of the Meridian 1 tow er .
Installing the 201i server in a large Meridian 1 system Standard 1.03 68 CallPil ot 7 Replace the protect iv e plate. 8 Replace the I/O panel co v er . 9 P ower up the sh elf . What’ s next? Prepare the modem, CD-R OM dri ve, an d tape dri ve for connection to the 201i server .
201i Server Hardware Installation 69 Chapter 5 Installing the 201i server in an Option 11C or Option 11C Mini In this chapter Installing the 201i ser ver in the Option 11C or Option 11C Mini s witch 7.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 70 CallPil ot Installing the 201i server in the Option 11C or Option 11C Mini s witch Introduction The 201i server occupies physical and electrical slots.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 71 See the following diagram: 2 Ensure that no cab les are connected t o the slots in which y ou are installing the 201i ser ver . 3 Open the loc k la tches at the t op and botto m of the 201 i server f aceplat e.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 72 CallPil ot 4 Slide the 201i server into an unoccupi ed pair of slots . Ensure that the 201i server is positione d correctly betw een the slots . Note: When correctly inser ted in the Opt ion 11C Mini, the top of the 201i server is on the left.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 73 What’ s next? Continue with installin g the cables.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 74 CallPil ot.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 75 Section A: Installing Option 11C cables In this section Installing the intermediate SC SI .
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 76 CallPil ot Installing the intermediate SCSI cable f or Option 11C Introduction Before you can connect an external CD-R OM or tape drive to the 201i server , Option 11C requires an inte rmediate SCSI cable (NTRH1407).
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 77 What the completed i nstallation looks like The follo wing diagram sho ws ho w the intermediat e SCSI cable, CD-R OM dri v e, and tap e dri v e are co nnected to the Option 11C.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 78 CallPil ot Note: Alternate SCSI de vice connection s cenarios are supported, but are not depicted in this guide. If you want to use a connection scenario that is not described in this guide, ensure that you use appropriate cabling for each device.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 79 T o install the cable 1 Attach the br ac k et assemb ly and cab le as f ollo ws: a. Below the card cage, tem porarily rem ov e the hardware that secures cabl e connections to the Option 11C .
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 80 CallPil ot See the following diagram: 2 Thread the cab le up thro ugh the card cage . Note: When routing the SCSI cable throug h the card cage , ensure the second cab le f errite is placed halfwa y through the opening.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 81 4 Leav e the lo w-profile ri ght-angle SCSI connecto r loose f or now .
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 82 CallPil ot 5 Replace all cab ling and hardw are that y ou remo v ed in step 1. 6 Restore any ser vices that you took out of ser v ice in step 1. What’ s next? Prepare the modem, CD-R OM dri ve, an d tape dri ve for connection to the 201i server .
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 83 Section B: Installing Option 11C Mini cables In this section Installing the NTRH3502 SCSI .
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 84 CallPil ot Installing the NTRH3502 SCSI cable f or Option 11C Mini Introduction Before you can connect a CD-R OM or tap e dri ve to the 201i server , you must install the NTRH3502 SCSI cab le.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 85 Note: Alternate SCSI de vice connection s cenarios are supported, but are not depicted in this guide.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 86 CallPil ot T o install the NTRH3502 SCSI cable 1 If yo ur Option 11C Mini is equipped with a Fiber Routing Guide , temporarily remov e it. Note: F or detailed instructions, ref er to the Option 11C and Optio n 11C Mini Expansion Guide (NTP 553-3021 -208).
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 87 See the following diagram: 3 Ref asten the inner SCSI br ac k et screws in the ir original locations inside the cabinet. Y ou will us e the top scre w later to f ast en the NTRH3502 SCSI cab le drain wire.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 88 CallPil ot SCSI cable installation to accommo date the Fiber Routing Guide 6 If required, reinstall the Fiber Ro uting Guide . Note: F or detailed instructions, ref er to the Option 11C and Optio n 11C Mini Expansion Guide (NTP 553-3021 -208).
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 89 See the following diagram: 7 Replace the cabinet co v er . What’ s next? Continue with “Installing cables on the back of the Option 11C Mini cabinet” on page 90.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 90 CallPil ot Installing cables on the bac k of the Option 11C Mini cabinet Introduction The follo wing items connect to t.
July 2006 Installing the 201i server in an Option 11C or Option 11C Mini 201i Server Hardware Installation 91 The f ollo wing diagr am shows ho w to secure the m ulti I/O cab le connection: 3 Attach the m ulti I/O cab le dra in wire to a scre w on the ca binet.
Installing the 201i server in an Opti on 11C or Option 11C Mini Standard 1.03 92 CallPil ot See the following diagram: What’ s next? Prepare the modem, CD-R OM dri ve, an d tape dri ve for connection to the 201i server . For instructions, see Chap ter 7, “Preparing peripheral de vices.
201i Server Hardware Installation 93 Chapter 6 Installing the 201i server in the Succession 1000 system In this chapter Succession 1000 description 94 Removing the Me dia Gatewa y or Media Gatewa y Ex.
Installing the 201i server in th e Succession 1000 system Standard 1.03 94 CallPil ot Succession 1000 description Introduction The Succession 1000 system is an IP PBX that provides telephony and data capabilities ov er an IP network.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 95 one A C po wer cord connector and On/Of f switch The follo wing diagram sho ws the Call Ser.
Installing the 201i server in th e Succession 1000 system Standard 1.03 96 CallPil ot The follo wing table identifies th e Media Gate way and Media Gateway Expansion slots into which yo u can install .
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 97 6 Not supported 6 Not supported Media Gateway Expansion Media Gateway Expansion 71 7 7 2 7 81 8.
Installing the 201i server in th e Succession 1000 system Standard 1.03 98 CallPil ot Back p anel connector s The follo wing table describes the connec tors that are located on the back of each Media .
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 99 The follo wing diagram sho ws the Media Gate w ay: One 10Base-T Ethernet connector that pro.
Installing the 201i server in th e Succession 1000 system Standard 1.03 100 CallPilo t Note: Except for the back panel conne c tors, the Media Gate way Expansion is similar in external app earance to the Media Gate w ay . Succession 1000 software For the 201i serv er , the Succ ession 1000 system must be running Succession Release 3.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 101 Succession 1000 documentation If you need to refer to the follo wing Succession 1000 tech nica.
Installing the 201i server in th e Succession 1000 system Standard 1.03 102 CallPilo t Remo ving the Media Gate wa y or Media Gate wa y Expansion co ver Introduction T o access the interior of the Media Gateway or Media Gate w ay Expansion, you must remove the front bezel and inside front cov er plate.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 103 a. Use a slot screwdriver to gently pr y off the SUCCESSION label.
Installing the 201i server in th e Succession 1000 system Standard 1.03 104 CallPilo t 2 Remov e the in side front co v er plate as f ollows: a. Use a screw driver to l oosen each scre w on the top of the inside front cov er plate by three tur n s. b.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 105 Installing the 201i server Introduction This section describes ho w to insta ll the 201i server inside the Media Gate way or Media Gate w ay Expansion.
Installing the 201i server in th e Succession 1000 system Standard 1.03 106 CallPilo t T o install the 201i ser ver inside the Media Gate wa y or Media Gate wa y Expansion 1 Ensure that no cab les are connected t o the slots in which y ou are installing the 201i ser ver .
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 107 What’ s next? Continue with “Installing the NTRH35 02 SCSI cable for Succession 1000” on page 108. A TTENTION Do not push the 201i server into place against the backplane until you are ready to obser ve the star tup cycle.
Installing the 201i server in th e Succession 1000 system Standard 1.03 108 CallPilo t Installing the NTRH3502 SCSI cable f or Succession 1000 Introduction Before you can connect a CD-R OM or tap e dri ve to the 201i server , you must install the NTRH3502 SCSI cable.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 109 Note: Alternate connection sce narios are su pported, but are n ot depicted in this guide. If you want to use a connec tion scenario that is not described in this guide, ensure that you us e appropriate cabling for each de vice.
Installing the 201i server in th e Succession 1000 system Standard 1.03 110 CallPilo t 2 Ref asten the inner SCSI br ac k et screws in the ir original locations inside the Media Gatewa y or Media Gatewa y Expansion. Y ou will use one of the screws later to f asten the NTRH3502 SCSI cable drain wire .
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 111 5 Replace the inside front co v er plate . F or instructions, see “ T o replace the inside front cov er plate” on page 112. 6 Replace the front bez el.
Installing the 201i server in th e Succession 1000 system Standard 1.03 112 CallPilo t Replacing the Media Gate wa y or Media Gate wa y Expansion co ver Introduction This section describes how to replace the front bezel and inside front co ver plate on the Media Gate way or Media Gate way Expansion.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 113 1 Inser t t he bottom ta bs of the fro nt cov er plate insid e the bottom rail. 2 Align the screw holes on the front cover plate ov er the screw heads on the Media Gatewa y or Media Gatewa y Expansion.
Installing the 201i server in th e Succession 1000 system Standard 1.03 114 CallPilo t T o replace the front bezel 1 Align the tw o posts and the loc king tab on the rear of the front bez el with the slots on the inside front co v er plate . 2 Push the bez el tow ard the Media Gate w a y or Media Gate wa y Expansion until it snaps into place.
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 115 Connecting cables to the Succession 1000 system Introduction The follo wing it ems are conn ec.
Installing the 201i server in th e Succession 1000 system Standard 1.03 116 CallPilo t c. Secure the connection b y tighte ning the retaining scr ew and V elcro f astening s trap of the cond uctor .
July 2006 Installing the 201i server in the Successio n 1000 system 201i Server Hardware Installation 117 4 Connect the po wer cord to the Media Gate wa y or Media Gate w a y Expansion. What’ s next? Prepare the modem, CD-R OM dri ve, an d tape dri ve for connection to the 201i server .
Installing the 201i server in th e Succession 1000 system Standard 1.03 118 CallPilo t.
201i Server Hardware Installation 119 Chapter 7 Preparing peripheral de vices In this chapter Ov erview 120 Setting the modem DIP s witches 122 Setting the CD-ROM driv e SCSI ID and DIP s witches 124 .
Preparing peripheral devices Standard 1.03 120 CallPilo t Overview Introduction Y ou can connect a modem and one or more SCSI de vices to the 201i serv er . The modem is connected to the 20 1i server by the multi I/O cable. The SCSI devices are connected to the 20 1i server by the intermediate SCSI cable.
July 2006 Preparing peripheral devices 201i Server Hardware Installation 121 tape dri ve (NTRH9038 ): T andberg SLR5 tape dri v e Note: This is currently the on ly su pported tape dri ve.
Preparing peripheral devices Standard 1.03 122 CallPilo t Setting the modem DIP s witches Introduction Set the modem DIP switches to their defa ult settings. This secti on describes ho w to set the modem DIP switches if they hav e been changed from the default sett ings.
July 2006 Preparing peripheral devices 201i Server Hardware Installation 123 4 OFF Command mode local echo suppressio n OFF: Displays ke yboard co mmands ON: Suppresses echo 5 ON Auto ans wer .
Preparing peripheral devices Standard 1.03 124 CallPilo t Setting the CD-R OM drive SCSI ID and DIP sw i t ch e s Introduction This section describes ho w to set the CD-R OM driv e SCSI ID and DIP switches. Note: The CD-R OM driv e discussed in this section is the ex ternal SCSI CD- R O M dri ve (NTRH910 5).
July 2006 Preparing peripheral devices 201i Server Hardware Installation 125 T o set the CD-ROM drive DIP s witches Set the CD-R OM drive DIP switches as described in the follo wing table: What’ s n.
Preparing peripheral devices Standard 1.03 126 CallPilo t Setting the tape drive SCSI ID Introduction This section describes ho w to set the tape dri ve SCSI ID. Note: The tape driv e discussed in this se ction is the T andberg SLR5 tape dri ve (NTRH9038).
July 2006 Preparing peripheral devices 201i Server Hardware Installation 127 T o change the SCSI ID, use the blade of a screwdri ver to press either the plus (+) or minus (–) b utton on the SCSI ID switch. Set the SCSI ID to 5. G101183 A C power receptacle Note: The appearance and size of the tape drive is subject to change .
Preparing peripheral devices Standard 1.03 128 CallPilo t Setting SCSI de vice termination Introduction If you want to connect SCSI de vices in a daisy chain, the last de vice in the daisy chain must be terminated. This section describes how to terminate the SCSI devices.
July 2006 Preparing peripheral devices 201i Server Hardware Installation 129 Meridian 1 For more information about the cablin g requirements, see “Installing the SCSI cables for Meridian 1” on page 63.
Preparing peripheral devices Standard 1.03 130 CallPilo t Option 11C, Option 11C Mini For more information about the cab ling requirements, see one of the follo wing: “Installing the intermed ia.
July 2006 Preparing peripheral devices 201i Server Hardware Installation 131 Succession 1000 For more information about the cablin g requirements, see “Installing the NTRH3502 SCSI cable for Succession 10 00” on page 108.
Preparing peripheral devices Standard 1.03 132 CallPilo t What’ s next? Complete the 201i serv er installa tion in the switch. See Chapter 8, “Connecting peripheral de vices to the 201i server . ” a tape dri ve only do nothing. External terminati on is no t required because the driv e is already internally terminated.
201i Server Hardware Installation 133 Chapter 8 Connecting peripheral de vices to the 201i ser ver In this chapter Ov erview 134 Installing the MPCs 138 Installing the monitor , keyboard, and mouse 14.
Connecting peripheral devices to the 201i server Standard 1.03 134 CallPilo t Overview Introduction This section describes installing the 20 1i server in the switch, connectin g peripheral devices, and starting the 201i server .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 135 Monitor , keyboar d, and mouse Connect the monitor , k eyboard, and mouse to the 201i server faceplate so that you can: observe the 201i server startup process.
Connecting peripheral devices to the 201i server Standard 1.03 136 CallPilo t 201i server faceplate and peripheral device connectors The follo wing diagram identif ies the pe ripheral device connector.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 137 Star ting the 201i server When you lock the 201i into positio n against the switch backplane, the server starts automatically . Y ou can ob serve the startup process on both the monitor and the 201i server f aceplate.
Connecting peripheral devices to the 201i server Standard 1.03 138 CallPilo t Installing the MPCs Introduction T wo MPCs are preinstalled at the f act ory . This section describes ho w to install additional cards, if required. Correct card insertion The MPC-8 card is ke yed so that it f its only one wa y into the slot on the 201i server f aceplate.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 139 f acing to the right if the 201i server is in ser ted into the 201i shelf (see the f ollowing diagr am) 3 Inser t the card into the slot, and gently push it until it is firmly in place and the ejector b utton po ps back out.
Connecting peripheral devices to the 201i server Standard 1.03 140 CallPilo t Installing the monitor , keyboar d, and mouse Introduction Y ou must connect the monitor , k eyboard , and mouse to the 201i serv er so that you can: observe the 201i server startup process.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 141 PS/2 extension cable The follo wing diagram sho ws the PS/2 e xtension cable connected between the 201i server and the USB mouse with USB-to-PS/2 con v erter .
Connecting peripheral devices to the 201i server Standard 1.03 142 CallPilo t Connecting the CD-R OM and tape drives Introduction Y ou can connect the CD-R OM, tape dri ve, or both to the intermediate SCSI cable that you installed earlier .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 143 Selecting the procedure f or y our switch T o connect the CD-ROM and tape drives to the 201i server (Meridian 1) Note: If you are connecting the SCSI de vices to the Option 11C, go to page 145.
Connecting peripheral devices to the 201i server Standard 1.03 144 CallPilo t 3 Connect the low- profile right-angle SCSI cab le connector to t he SCSI connector on the 201i se r ve r f aceplate. 4 Connect an ad ditional device in a daisy chain, if requir ed, using either th e SCSI cable supp lied with the de vice or an NTRH3502 cab le .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 145 that is not describ ed in this guid e, ensure that you use ap propria te cabling f or each SCSI de vice. 5 Connect the po wer cord f or ea ch de vice. 6 P ower up the de vices.
Connecting peripheral devices to the 201i server Standard 1.03 146 CallPilo t The f ollo wing diag ram sho ws cab le connection s, where the CD-R OM drive is the first device: Note: Alternate SCSI de vice connection scenarios are supported, but are not depicted in this guide .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 147 T o connect the CD-ROM and tape drives to the 201i server (Option 11C Mini) 1 Connect the first SCSI de vice.
Connecting peripheral devices to the 201i server Standard 1.03 148 CallPilo t Note: Alternate SCSI de vice connection scenarios are supported, but are not depicted in this guide . If y ou wan t to use a connection scenario that is not describ ed in this guid e, ensure that you use ap propria te cabling f or each SCSI de vice.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 149 T o connect the CD-ROM and tape drives to the 201i server (Succession 1000) 1 Connect the first SCSI de vice.
Connecting peripheral devices to the 201i server Standard 1.03 150 CallPilo t The f ollo wing diag ram sho ws cab le connection s, where the CD-R OM drive is the first device: Note: Alternate SCSI de vice connection scenarios are supported, but are not depicted in this guide .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 151 Connecting the 201i server to the switc h, ELAN, and CLAN Introduction The CLAN and ELAN co nnections are established by using the 201i serv er multi I/O cable.
Connecting peripheral devices to the 201i server Standard 1.03 152 CallPilo t Note: Ensure that the cable is securely f astened. 2 If y ou ha v e not already done so , connect the ampheno l connector .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 153 Option 11C Mini or Succession 1000 to a scre w on th e back of the cabinet 3 Connect the connector o n the multi I/O cable that is labeled as EL AN to the switch network hub.
Connecting peripheral devices to the 201i server Standard 1.03 154 CallPilo t Connecting the modem Introduction Y ou must connect the modem to th e 201i server if: you want to administer the 201i serv er from a remote location. you need assistance from Nortel technical support.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 155 2 Attach the serial cab le as f ollo ws: a. Connect the 25-pin ma le end of the serial cab le to th e modem. b. Attach the 0.25 -inch nuts to the thumbscrews on the 9-pin female connector on the se rial cable .
Connecting peripheral devices to the 201i server Standard 1.03 156 CallPilo t 6 P o wer on the m odem. Note: Ensure that the mo dem is receiving pow er b y checking t hat at least one LED on its front panel is lit. 7 Place the modem in an area wh ere it cannot be accid entally damaged or where people cannot trip ov er attach ed cords.
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 157 Completing the installation Introduction T o complete the installatio n of the 201 i server , lock the 201i into position . The server starts up automatically .
Connecting peripheral devices to the 201i server Standard 1.03 158 CallPilo t Result: The operating system boot sequence be gins, an d communication with the s witch occurs . The HEX displa y sho ws NT (f or about 30 seconds), f ollowed b y OK. Note: The system reboot s more than once .
July 2006 Connecting peripheral devices to the 201i se rver 201i Server Hardware Installation 159 6 Ensure that the oper ating system logon windo w appears on the monitor .
Connecting peripheral devices to the 201i server Standard 1.03 160 CallPilo t.
201i Server Hardware Installation 161 Appendix A RoHS p art conversion t able In this appendix RoHS part conversion t able 162.
RoHS part conversion table Standard 1.03 162 CallPilo t RoHS p art conversion t able This appendix provides a mapping of RoHS-compliant parts to the equivalent non-RoHS-complian t parts for the 201i server .
July 2006 RoHS part conversion table 201i Server Hardware Installation 163 T able 1: RoHS part con version table Ty p e RoHS part description (The non-RoHS par t description is in cluded belo w in par.
RoHS part conversion tabl e Standard 1.03 164 Call Pilot T able 1: RoHS part con version table (cont’ d) Ty p e RoHS part description (The non-RoHS par t description is in cluded belo w in pare nthe.
July 2006 RoHS part conversion table 201i Server Hardware Installation 165 T able 1: RoHS part con version table (cont’ d) Ty p e RoHS part description (The non-RoHS par t description is in cluded b.
RoHS part conversion table Standard 1.03 166 CallPilo t.
201i Server Hardware Installation 167 Inde x Numerics 201i server components, diagram 16 damaged, what to do 40 faceplate connections 29 description 18 – 20 diagram 17 , 136 inspecting 40 installati.
Index Standard 1.03 168 CallPilo t connectors CLAN 27 ELAN 27 RS-232 28 switch 27 diagram 26 installing large Meridian 1 s ystem 151 Option 11C 151 Option 11C Mini 90 , 152 Succession 1000 152 cable, .
July 2006 Index 201i Server Hardware Installation 169 keyboard 18 , 29 monitor 18 , 29 mouse 18 , 29 SCSI 30 SCSI de vice 19 switch, multi I/O cable 27 copyright 2 cove r , re mov in g small Meridian .
Index Standard 1.03 170 CallPilo t CD-R OM dri ve 125 modem 122 documentation, Succession 1000 101 drain wire, connecting Option 11 C 152 Option 11C Mini 153 Succession 1000 153 E ejector buttons , MP.
July 2006 Index 201i Server Hardware Installation 171 L latches, lock 18 LEDs CLAN 20 ELAN 20 hard driv e 20 MPC status 18 – 19 power status 18 SCSI dri v e 20 lock latches 18 M Media Gatew ay and M.
Index Standard 1.03 172 CallPilo t installation diagram 66 installing 66 NTRH1410 cable 64 installation diagram 66 installing 66 NTRH3501 cable 56 diagram 60 installing 61 NTRH3502 cable 84 , 108 inst.
July 2006 Index 201i Server Hardware Installation 173 daisy chain scenarios Meridian 1 129 Option 11C 130 Option 11C Mini 130 Succession 1000 131 installation, attention 124 , 126 , 128 supported 120 .
Index Standard 1.03 174 CallPilo t connecting Meridian 1 143 Option 11C 145 Option 11C Mini 147 Succession 1000 149 description 31 device termination, setting 132 installation, attention 124 , 126 , 1.
.
201 i Se r ver H ard ware In sta l la t io n CallPilot Rel ea se 4.0 Document Number: 555- 7101- 2 20 Document V ersion : Standar d 1.03 July 2006 All Rights Reserved.
An important point after buying a device Nortel Networks CalPilot 4.0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nortel Networks CalPilot 4.0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nortel Networks CalPilot 4.0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nortel Networks CalPilot 4.0 you will learn all the available features of the product, as well as information on its operation. The information that you get Nortel Networks CalPilot 4.0 will certainly help you make a decision on the purchase.
If you already are a holder of Nortel Networks CalPilot 4.0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nortel Networks CalPilot 4.0.
However, one of the most important roles played by the user manual is to help in solving problems with Nortel Networks CalPilot 4.0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nortel Networks CalPilot 4.0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
