Instruction/ maintenance manual of the product AN/DC Nortel Networks
Go to page of 150
Part No. 312 410-A Rev 00 Novembe r 2000 600 Techno logy Park Driv e Billeric a, MA 01821-4 130 Installing and Operating AN/DC and ANH-8/DC Systems.
ii 312410-A R ev 00 Copyri ght © 2000 Nortel Netw orks All rights reserved. Nov ember 2000 . The inform ation in this do cument is sub ject to c hange witho ut notice.
312410-A R ev 00 iii EC Dec laration of Conf ormity This pro duct co nforms ( or thes e pr oduc ts co nfor m) to th e provision s of Coun cil Dire ctive 89/336/EEC and 73/23/EEC.
iv 312410-A R ev 00 Canada Requirements Only (continued) Repai rs to cert ified equipm ent sho uld be coo rdin a t ed by a repr e sentat iv e desi gn ated by t he suppli er .
312410-A R ev 00 v FCC P art 68 Compliance Statement This equipme nt complie s with P art 68 of FCC Ru le s. All direc t c onnec tio ns to telepho ne netw ork line s mu st be mad e using sta ndard plu gs and jacks c ompliant with FCC Part 68. Please n ote the follo wing: 1.
vi 312410-A R ev 00 Nor tel Netw orks NA Inc. Software License Agreement NO TICE: Please carefu lly read thi s licen se agr eement before copyi ng or usin g the accom panying software o r installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement).
312410-A R ev 00 vii for the se curity of its o wn da ta and i nformation and for maintain ing adequat e procedures a part from the Software to reconstru ct lost or al tered f iles, data, o r programs.
.
312410-A R e v 00 ix Contents Preface Befo re Y ou Begi n ............... ............. ............. ................... ............. ................... ............. ... xv ii T e xt Conventions ........ ............. ............. ...............
x 312410- A Re v 00 Connectin g a Manage ment Con sole or Modem ............. ............. ................... ............. . 1-12 Connectin g a T er min al Consol e ..... .................... ............. ................... ............. ....... 1-12 Connectin g a PC Cons ole .
312410-A R e v 00 xi Chapter 3 Star ting the AN/DC and ANH-8/DC About Software Installatio n ................... ............. ....... ...... ....... ...... ...... ............. ....... ...... ... 3-1 Boot Opt ions ........ .................... ......
xii 312410- A Re v 00 Appendix B Using Local Boot (the Quick-Start Procedure) Filling Ou t the Quick-Star t W orkshee ts .................... ............. ................... ............. ........ B-2 Global Informa tion Worksheet .. ...... ........
312410-A R e v 00 xiii Figures Figure 1-1. Mounti ng Hardware .. ...... ....... ...... ....... ...... ....... ...... ...... ............. ....... ...... ... 1-2 Figure 1-2. Console C ables ........ ................... ............. ...................
xiv 312410- A Re v 00 Figure 2-17 . Connectin g a PC Cons ole to the ANH-8/DC ......... ................... ............. . 2-23 Figure 2-18 . Connectin g a Modem to the A NH-8/DC ................ ................... ............. . 2-25 Figure 2-19 .
312410-A R e v 00 xv Ta b l e s T able 1-1. Console Parameters ............. ............. ................... ............. ................... . 1-13 T able 1-2. Modem P arameters ........ ....... ...... ....... ...... ....... ............ ....... .
xvi 312410- A Re v 00 T able D-7. V .35 Interface (Order No. 7220) ......... ............. ................... ............. ........ D-5 T able D-8. X.21 Interface (Order No . 7224) .. ............. ................... ............. ............. .. D-6 T able D-9.
312410-A R e v 00 xvii Preface Read this guide for instruc tions on h ow t o instal l, start , and opera te Access Node or 8-Por t Access Node Hub mod els that ha ve a singl e DC input swit ching po wer supply , the AN™/DC and ANH™-8/DC.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems xvii i 3124 10-A Re v 00 T ext Con venti ons This gui de uses the follo wing t ext con vention s: angle br acket s (< >) Indicate that you c hoose the text to enter based on t he descript ion insi de the bra ckets.
Prefac e 312410-A R e v 00 xix Acr on yms This gui de uses the follo wing a cron yms: screen text Indicate s system output , for e xample, prompt s and syst em m ess ag es. Example: Set Trap Monitor Filters vertical line ( | ) Separates choices f or command k eyw ords and arg uments.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems xx 312410- A Re v 00 IEEE Institut e of Electrical an d Electr onic Engi neers IP Internet Protocol ISDN Integ rated Services Digital Ne twork IS.
Prefac e 312410-A R e v 00 xxi Har d-Co py T echni ca l Manuals Y ou can pr int sele cted techni cal manuals and rele ase notes free, dir ectly from t he Inter net . Go to the support.ba ynetwor ks.com/li brary/tp ubs/ URL. Fin d the product for wh ich you nee d documentatio n.
.
312410-A R e v 00 1-1 Chap ter 1 Installin g the AN/ DC This chap ter descr ibes ho w to install th e AN/DC. T op i cs in th is cha pter incl u de • Prep ar ing fo r In st alla ti on • Insta lling.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-2 312410- A Re v 00 1. Inspect a ll items f or any sh ipping damage. 2. Make sur e tha t y our shippi ng package contai ns the f ollowing items : • Mounti ng hardwa re (Figure 1-1) . • Consol e/modem cabl e kit (Figure 1-2 ) .
Install ing the AN/ DC 312410-A R e v 00 1-3 Figure 1-2. Console Cables Supplying T ools and Equip ment Y ou may need items that are not part of the ANH- 8/DC shippin g acces sories. Befo re ins tall ing th e AN H-8/D C ha rdwa re , ens ure th at y ou have all th e ca b les, tools, a nd other e quipment th at you need at your si te.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-4 312410- A Re v 00 Service Console Y ou can at tach an opt ional VT -100 console or equi v alen t to the AN/DC t o monitor the res ults of s t.
Install ing the AN/ DC 312410-A R e v 00 1-5 Space Requirements The inst allati on site must pr ov ide a certa in amount of free spa ce around t he AN/D C to di ssi pate heat . In stal l t he A N /DC in a sp ace that m eet s t he fo llowing spec if ications : • W idth: 19.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-6 312410- A Re v 00 Installing the AN/DC W ith all cabl ing at tached , you can i nstal l the AN/DC in an y of the fo llo w ing w ays : • Positi on the AN/DC on a flat, st urdy surf ace. • Ins tall the AN /DC i n an elec tr oni c encl osur e rac k.
Install ing the AN/ DC 312410-A R e v 00 1-7 T o insta ll the AN/DC in a rack: 1. Attach eac h flange brack et to t he AN/DC (Fig ure 1-3) as f ollows: a. Align the flange hol es with the AN/DC m ounting holes. b. Insert a flange sc rew thr ough eac h flange hol e and into the AN/ DC.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-8 312410- A Re v 00 Figure 1-4. Installing the AN/DC in a Rack Y ou can no w connect the network cables t o your AN/DC. Go to the se ction “ Connecting Communic ations Cables , ” late r in this ch apt er .
Install ing the AN/ DC 312410-A R e v 00 1-9 Mounting the AN/DC on a W all When mounting the AN/DC on a w all, k eep the fol lo wing in mind : • Ma ke s ure th at th e wall i s at l east 3/8 in . (0. 9 6 cm) thic k, an d is m ad e of Sheetroc k or wood .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-10 312410- A Re v 00 Figure 1-5. Mounting the AN/DC on a W all RUN BOOT DIAG POWER Rubber feet AN0005A.
Install ing the AN/ DC 312410-A R e v 00 1-11 Connecting Co mmunications Cables T o connect ne twork c ables to the back of the AN/DC: 1. Connect the appr opriate ca bles f or y our network conf iguration to the communicati ons ports on the back of t he AN/DC (F igure 1-6) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-12 312410- A Re v 00 Connecti ng a Managemen t Console or Mod em Use t he fro nt-panel con sole port to connect an ASCII-ba sed termin al, a pers onal comput er termina l emulator , or a modem to th e AN/DC.
Install ing the AN/ DC 312410-A R e v 00 1-13 Once you ha v e th e appropri ate equip ment, complet e the fol lo wing step s: 1. P ower o n and conf igur e the cons ole, using the parameters i n Ta b l e 1 - 1 . Refer t o the consol e user manu al for i nstructions .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-14 312410- A Re v 00 Figure 1-8. Connecting a T erminal Console 6. Atta ch the 25- p in recep tac le con n ect o r on th e co m bin ed cab le an d adapte r to the termi nal’ s host connect or .
Install ing the AN/ DC 312410-A R e v 00 1-15 Once you ha v e th e appropri ate equip ment, complet e the fol lo wing step s: 1. Insert t he 9-pin r eceptacle end of the consol e cable i nto the CONSOLE port on th e AN/DC back pan el (Figur e 1-9) . 2.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-16 312410- A Re v 00 Connecting a Modem A modem p rovides remot e acce ss to th e AN /D C fo r a net work ad minis trat or . W e recomme nd that you connect a mod em in case t he AN/DC e xperienc es system problems.
Install ing the AN/ DC 312410-A R e v 00 1-17 2. Po wer off the modem. 3. Insert t he 9-pin r eceptac le end of the modem c able into t he back-pane l CONSOLE port of the AN/DC (Fi gure 1-10) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-18 312410- A Re v 00 4. Insert t he 25-pin pl ug at the other end of the mode m cable into the modem’ s RS-232 data communic ations port . The modem is no w conne cted to the AN/DC. Next , connect t he po wer source as desc ribed in the foll owi ng secti on.
Install ing the AN/ DC 312410-A R e v 00 1-19 3. Strip 3/ 8 in. (10 mm) of in sulation f rom t he end of a #16 or # 18 A WG cabl e. 4. Insert t he strippe d end of the cable into the -VDC termi nal bloc k, the minus lead (Figure 1-12 ) . 5. T ighten the sc rew b eneath the -VDC ter minal block t o establish the electr ical conne ction.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-20 312410- A Re v 00 9. Connect an e arth gr ound to eithe r the leftmost terminal block or to the gr ounding stud, loc ated between the power switch and termi nal conn ecto rs (Fig ure 1 -13) .
312410-A R e v 00 2-1 Chap ter 2 Installing the ANH-8/DC This chap ter descr ibes ho w to install th e ANH-8/DC. T op i cs in th is cha pter incl u de: • Prep ar ing fo r In st alla ti on • Instal.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-2 312410- A Re v 00 V e rifying Shipment Contents V erify that the ite ms you rec ei ve mat ch the it ems in the pa cking list a ttached t o the shi pp ing cont ain er . 1. Inspect a ll items f or ship ping damage.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-3 Figure 2-1. Accessories in the ANH-8/DC Shipping Container Supplying T ools and Equip ment Y ou may need items that are not part of the ANH- 8/DC shippin g acces sories.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-4 312410- A Re v 00 Cables Unless t hey wer e specif ically ordere d, the Ether net and sy nchronous c ables necessa ry for your networ k conf igurat ion are n ot part of the ANH-8/DC s hipping accesso ries.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-5 V e rifying Site Requi rements V erify that your in stallat ion meet t he requir ements lis ted in th is secti on.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-6 312410- A Re v 00 En vironmental Require ments The ANH-8/DC in stallat ion site must meet the f ollo win g en vironmental spec if ications : .
Installi ng the ANH- 8/DC 312410-A R e v 00 2-7 Installing the ANH-8/DC in a Rack F or this proc edure, you need • F our #10 cagenut scre ws and washers (s hipped wit h the ANH-8/DC) • T wo fl ang.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-8 312410- A Re v 00 Figure 2-3. Attac hing Flange Brackets to Rac k-Mount the ANH-8/DC 2. Align the flange brack et holes wit h the holes in the fr ont v ertica l supports of the ra ck (Fig ure 2 -4) .
Installi ng the ANH- 8/DC 312410-A R e v 00 2-9 Figure 2-4. Installing the ANH-8/DC in an Electronic Enclosure Rac k 3. Insert a cagenut scr ew through eac h bracket hole and into t he corr espon ding holes i n the rack. 4. T ighten each ca genut scr ew with a Phillips sc rewdr iver .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-10 312410- A Re v 00 Mounting the ANH-8/DC on a W all F or this proc edure, you need • T wo fl ange brack ets an d four #6 r oundhead scr e w.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-11 Figure 2-6. Mounting the ANH-8/DC on a W all 3. Insert t wo to f our wall anchor sc rews thwro ugh the holes in each flange bracke t, and fast en each scr ew secur ely i n the wall.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-12 312410- A Re v 00 Connecting Co mmunications Cables Gather t he communicat ions equi pment and cab ling that you will att ach to th e ANH-8/DC. If you do not ha ve the proper cables, cont act your n etwork admini strator or see the Cable Guide for Rout ers and BNX Platforms .
Installi ng the ANH- 8/DC 312410-A R e v 00 2-13 Connecting Ethernet Repe ater P or t UTP Cables T o connect unshielded twisted- pair (UTP) c ables to the front panel 10Base- T repeat er ports, attach t he UTP cables to the fr ont-pane l RJ-45 conn ectors (Ethern et Repeate r Ports 1- 8), as sho wn in Figure 2 -8 .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-14 312410- A Re v 00 Figure 2-9. ANH-8/DC Front- P anel MDI-X/MDI Switch Connecting the ANH- 8/DC to Other Repeaters/ Hubs Y ou can use Port 1 .
Installi ng the ANH- 8/DC 312410-A R e v 00 2-15 When you conf igure a netw ork with multiple ANH- 8/DC (or ot her repeat er/hub) systems, y ou must comply with the f ollo win g rules: • Connect no more than f our hubs. • Make sure tha t each UTP con nection i s not longe r than 100 meters (109.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-16 312410- A Re v 00 Figure 2-11. Linking Hubs Refer to “10 Base-T Repea ter Ports (ANH- 8/DC only)” in Appendix C for more info rmation.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-17 Connecting a Second Eth ernet Interface UT P Cable Complete t hese step s to connec t a UTP cable t o the back p anel UTP-2 po rt. 1. Atta ch a U TP ca b le t o the b ack- pan el RJ- 45 c onn ec tor ( Figur e 2-12 ).
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-18 312410- A Re v 00 Connecting Synchr onous Cables Connect on e to th ree synchr onous inter face c ables to t he back of the ANH-8/DC: 1. Locate th e RS-232, RS-422 , V .28, V .35, or X.21 inter face cable.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-19 Connecting an ISDN Cable Connect a n ISDN BRI cable to the back of the ANH-8/DC: 1. Plug the I SDN cable into the ISDN-BRI connect or ( Figur e 2-14 ). Figure 2-14. Connecting an ISDN BRI Ca ble 2. Connect the other end of the cable to the ISDN communi cations de vice.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-20 312410- A Re v 00 Connecti ng a Managemen t Console or Mod em Use t he fro nt-panel con sole port to connect an ASCII-ba sed termin al, a pers onal computer terminal e mulator , or a modem to th e ANH-8/DC.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-21 4. Insert t he scr ew on th e cable’ s connector i nto th e re ceptacle on the adapte r’ s co nnector and tigh ten the scr ew (Figu re 2-15) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-22 312410- A Re v 00 6. Insert t he 9-pin r eceptacle end of the consol e cable i nto the ANH-8/DC console p ort conn ector .
Installi ng the ANH- 8/DC 312410-A R e v 00 2-23 Figure 2-17. Connecting a PC Console to the ANH-8/ DC 5. Attach th e 25-pin r eceptacl e end of the cabl e-plus-adapt er to the PC console c able’ s 25-pin plug con nector . 6. Connect the complete cable unit to th e communications po rt at the back of the PC ( Figur e 2-17) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-24 312410- A Re v 00 Comple te the following ste ps: 1. Conf igur e the modem, using the par ameters in T able 2-2 . Refe r to the mo d em use r manual f or ins truct ions. 2. Po wer off the modem.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-25 Figure 2-18. Connecting a Modem to the ANH-8/DC 4. Insert t he 25-pin pl ug at the other end of the mode m cable into the modem’ s RS-232 data communic ations port .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-26 312410- A Re v 00 Connect ing to th e DC P ower Source T o connect t he ANH-8/DC to the p owe r source: 1. Ensure th a t the p ower s w itch is in th e OFF ( 0) pos i tion ( Figure 2-19) . 2.
Installi ng the ANH- 8/DC 312410-A R e v 00 2-27 Figure 2-20. Attac hing the ANH-8/DC Po wer Input Cables 6. Strip 3/ 8 in. (10 mm) of in sulation f rom t he end of a #16 or # 18 A WG cabl e. 7. Insert the stripped end of the cabl e into the R TN terminal block, the plus lead (Figur e 2-20) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-28 312410- A Re v 00 Figure 2-21. Att aching the ANH-8/DC Ear th Gr ound Cable 10. Bef ore qualif ied ser vice pe rsonnel connect the ANH-8/DC to t he power sour ce, ve rify that th e power s witch is OFF and that the ANH-8/DC has been pr operly g rounde d.
312410-A R e v 00 3-1 Chap ter 3 Star ting the AN /DC and ANH-8/DC The f irst ti me you start the AN/DC or ANH-8/DC, y ou complete an importa nt softw are conf iguration pr ocess. Befo re you b egin the in itia l s tart up fro m a re mo te si te : 1. Coordinat e with your networ k administ rator .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-2 312410- A Re v 00 Y ou must co mplete an i nitial startup p rocedure to o btain the necessar y f iles and connect the AN/DC or ANH-8/DC to the netw or k. Ge tt ing a f ile o ver the net w ork is calle d network booting, or netbo oting .
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-3 Installing the Flash Memory Car d A PCMCIA Flash memor y card (Figur e 3-1) pro vides st orage cap ability for the non volat ile f ile system ( NVFS) in th e AN/DC and ANH-8/DC. When you r emo ve a form atted memory card, the NVF S automatic ally remo ves a ccess to the card.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-4 312410- A Re v 00 1. P osition t he card with t he label faci ng up and the I NSER T arrow pointing toward t he card r eceptacle.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-5 Figure 3-3. Inserting a Fla sh Memory C ar d in the ANH-8/DC Car d Receptacle Using EZ Ins tall T o use th e EZ Install f eature: 1. Install the r outer and attached communicatio ns equipment as described in Chapter 1 (AN/DC) or Chapter 2 (ANH-8/DC).
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-6 312410- A Re v 00 Using Ne tboot, Dire cted Netboo t, or Local Bo ot Y ou use a c ommand inter face to t he router softwa re, the Di agnostic Monitor , for Netbooti ng or Local Booting. (Y ou can also use th e T echnician Int erfa ce or Site Manager for the Directed Ne tboot proc edure.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-7 Figure 3-4. Running Dia gnostics 5. Bef ore diagnost ics ar e comple te, si multaneously hold down t he contr ol and c keys to bypas s the automatic boot pr ocess. The AN Diagnosti cs login prompt appea rs.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-8 312410- A Re v 00 Figure 3-5. Log ging In to the Diagnostic Monitor 6. T ype the f ollowi ng command at the login pr ompt and pr ess the Retur n key: Manager Note that yo u must type Manager with an upperca se “M.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-9 Continuing with Netboot 1. Contact y our network a dministrator t o veri fy that the ne twork is set up f or the Net boot pr ocedur e. 2. Ask y our network admi nistrato r (or r efer t o Ap pendix A) f or the interf ace conf igur ation command to use in Step 3.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-10 312410- A Re v 00 Figure 3-7. V erifying the Interface Configuration 5. If the c onf iguration i nf ormation is cor rec t, continue to the next st ep. Otherwise, r eenter t he corr ect ifconfig command.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-11 Figure 3-8. Netboot 7. When y ou boot the rout er , it s LEDs flash in a pa rticular orde r . T o interpre t t he LED se quence and t rou ble shoo t an y potential pr oble m s, re fe r to Chapte r 4.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-12 312410- A Re v 00 Continuing with Directed Netboot Before yo u can use the Di rected Net boot procedur e, you must ha ve already use d the ifconfig command (as describe d in the pr e vious sec tion) to conf igure t he interf ace f rom which you p lan to use Directed Ne tboot.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-13 4. T ype th e f ollow ing co mm and and press t he Retur n key t o verify t he conf iguration that y ou specif ied in Step 3 (Figur e 3-10) : getcfg Figure 3-10.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-14 312410- A Re v 00 Figure 3-11. Directed Netboot After t he router reboots, it gets a con figurati on file from a TFTP ser ver and loads t he softw are ima ge from the local f ile system. The route r start s bridging an d routing traf f ic.
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-15 Continuing with Local Boot Y ou need to use both the Dia gnosti c Monito r and th e T echnician Inter fa ce to loc al boot the AN. Before st arting the Lo cal Boot proce dure, ask y our netw ork admini strator for ass istance i n comp leting t he Quick-St art wo rkshee ts in Appendix B.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-16 312410- A Re v 00 Figure 3-12. Local Boot 4. When y ou boot the rout er , it s LEDs flash in a pa rticular orde r . T o inter pr et the LED seque nce and tr oubleshoot any potenti al probl ems, refer to Ch apte r 4; then return t o Step 5 .
Starting th e AN/DC and ANH-8/ DC 312410-A R e v 00 3-17 Figure 3-13. Logging In to the T echnician Interface and Mounting a Vo l u m e 6. T ype the f ollowi ng command and pr ess the Retur n key to begin the Quick-Star t pr ocedure: run install.bat 7.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-18 312410- A Re v 00 8. When the T echnician Int erface pr ompt r eappea rs, type the f ollowing command and pr ess the Retur n key to exit the T echnician Int erface: logout Once the install script completes, the router starts b ridging and r outing t raf f ic.
312410-A R e v 00 4-1 Chap ter 4 Operating the AN/D C and ANH-8/DC This chapte r describ es • Ensu ring a Succ ess ful I n stal lati o n (using t he front- panel LEDs) • Checki ng the statu s of t.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-2 312410- A Re v 00 Ensuri ng a Succe ssful Inst allation After co nnecting t he route r to the n etwork, you can ensur e a succe ssful instal lation b y checking t he LEDs on th e front pa nel.
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-3 When po wer is supplied t o the rout er , the follo wing LED sequence should occ ur: • The PO WER LED lights and rema ins on. • R UN, BOO T , and DIA G (or F A UL T for ANH) LEDs light for appro ximately 1 second, then turn of f, ind icating tha t the rout er is f unctioning.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-4 312410- A Re v 00 AN/DC LED Desc rip tions LEDs on the AN/DC front and back panels pr ovi de informatio n about ho w the AN/DC is oper ating. The fol lo wing sectio ns descri be the AN/DC front - and back-pan el LEDs.
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-5 Back-P anel LEDs The LEDs on t he AN/DC back-pa nel dif f er depending on the AN/DC model that you ha ve . Ta b l e 4 - 2 describes al l of the av ailable AN/DC ba ck-panel LEDs. These LEDs indic ate the s tatus of the AN/DC’ s netw ork conn ections.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-6 312410- A Re v 00 ANH-8 /DC LED D escri ptions LEDs on the ANH-8/DC fr ont and bac k panels pr ovid e informat ion about ho w the ANH-8/DC is opera ting. Fr ont-P anel LEDs Figure 4- 2 sho wn earl ier illust rates t he three s ets of st atus LEDs on th e ANH front panel.
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-7 Back-P anel LEDs Figure 4- 3 illustr ates the back-panel LEDs for th e ISDN and Seco nd Ethernet options . These LEDs ar e visibl e after in stalling either a n ISDN BR Inter face or Second Eth ernet Int erfa ce upgrade module.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-8 312410- A Re v 00 Ta b l e 4 - 4 describes t he back-p anel LEDs. P owe ri ng On and Of f The DC po wer switch allo ws yo u to rest art the router with out havi ng to disconnect the po wer supply wire s.
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-9 Figure 4-4. AN/DC P ower Switch Figure 4-5. ANH-8/DC P ower Switch 2. V erify that ai r i s f lo wi n g by plac ing y o ur han d to the s ide of the f an v e nts. T o po wer of f, press the switch to th e Of f posit ion (0); toggle th e switch up.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-10 312410- A Re v 00 Resetting the AN/DC or ANH-8/DC Yo u can use th e Reset b ut ton to r eboot th e router hardw are wit hout c y cling po wer , as fol lows: •T o warm-boot t he router (no diagno stic tests run), pre ss the Rese t b utton fo r less t han 3 second s.
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-11 AN/DC Reset Switch On the AN/DC, t he Reset b utton i s located on t he back pan el of the AN/DC (Figu re 4-6 ) . Labeled “RST ,” it res ides between t he console por t and the LED labele d “RLSD2.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-12 312410- A Re v 00 Remo ving a Flash Memory Car d When you remo v e a formatt ed memory card, t he NVFS aut omatically remo ve s access t o the car d. When you ins ert and f ormat a car d or insert an alread y formatt ed card, t he NVFS automati cally pr ovid es access .
Operati ng the AN/DC and ANH-8/ DC 312410-A R e v 00 4-13 Pr otecting Memory Car d Files Nort el Netwo rks ships each memo ry ca rd wit h it s read -wri te pro t ect sw i tch in the unprote cted posit ion (Figu re 4-10) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-14 312410- A Re v 00.
312410-A R e v 00 A-1 Append ix A Configuring Net boot and Directed Netboot Y ou c an use the fo llowing co mmands to con figure th e A N/D C or ANH -8/D C fo r Netboot a nd Directe d Netboot: • Use th e i fconfig comm and to configure the r o ute r’ s init ia l IP i n terfac e to the netw ork.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-2 312410- A Re v 00 Configuring a Synchr onous IP Int erface for Netbooting T o Netboot, you must firs t confi gure the route r’ s initi al I.
Configur ing Ne tboot and Di rected Netboot 312410-A R e v 00 A-3 Configuring an Ethernet In terface for Netbooting T o conf igure an Ethernet interf ace for Netbootin g, use the fo llo wing co mmand .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-4 312410- A Re v 00 Enab ling and Disab ling Interfaces with ifconfig T o enable or disable a n interf ace f or the Netb oot proces s, use the .
Configur ing Ne tboot and Di rected Netboot 312410-A R e v 00 A-5 T able A-3. The bconfig Command Options Opt ion Des cr ipti on imag e Spe cifie s infor mat io n abou t the s oft ware im age. config S pecifies in f ormation about the confi gura tion file .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-6 312410- A Re v 00.
312410-A R e v 00 B-1 Append ix B Using Local Boot (the Quic k-Star t Procedure) Y ou can loc al boo t the AN/DC or ANH-8/ DC us in g t he Sit e Manager Qui ck- Sta rt procedur e exp lained i n this appe ndix. Y ou need t his info rmation to complete t he procedur e in “Continui ng with Loca l Boot” on p age 3-15 .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-2 312410- A Re v 00 Fillin g Out th e Quick-Star t W orkshee ts The in stall. bat scri pt pro vides man y opti ons for c onf iguring t he router on a netw ork. Use the f ollo wing workshe ets to or ga nize your n etwork informati on.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-3 Global Information W orkshe et This sec tion cont ains the p rompts and p ossible o ptions re lating to al l AN/ANH synchron ous conf igura ti ons . Wri te your s ele ct ion in t h e “ Y our Res ponse” col u mn.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-4 312410- A Re v 00 3 Enter IP address in dotted decimal notation: Enter the I P addres s f or the CO M inte rface. Enter the subnetwork mask in dotted decimal notation: Enter the subnetwork mask f o r the COM interf ace IP address.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-5 Router Pr otocol W orksheets This sec tion cont ains requ ested info rmation and po ssible op tions rel ating t o the routing protocol choices o n the Global Informat ion W orkshee t.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-6 312410- A Re v 00 Enter OSPF MTU size selection [1]: 1. Default 2. E ther net size (N or tel Networ k s Series 5 com patib le) 3. User defi ned MTU Enter OSPF interface type selection [1]: 1. Broadc ast 2.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-7 Enter decimal value in seconds for Poll Interval [20]: (F or NBMA onl y) Enter the l argest n umber of seco nds allo wed betwe en Hello pa ck ets that the route r sends to an inact iv e NBMA ne ighbor .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-8 312410- A Re v 00 Static Rout e to Sit e Manager W orksheet Requested Inf ormation Options Y our Inf orma tion Destination Network [0.0.0.0]: Enter t he gate w a y address of the desti nati on ne twor k.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-9 Wide Area Protocol W orksheets This sec tion cont ains requ ested info rmation and po ssible op tions rel ating t o wide area pr otocol cho ices on th e Global I nformation W orksheet.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-10 312410- A Re v 00 Enter address field length: 2. T wo Bytes 3. Three Bytes 4. Four B y t es Enter DLCI number [30]: (F or DLCMI None , LMI Switc h, Anne x D Switch , and Anne x A Switch only) Enter the P e r manent Vir tual Circui t (PVC) num ber .
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-11 Enable the LQR (Link Quality Reporting) Protocol? (y/n) [n]: y(es) n(o) Note: Link Qual ity Moni toring on a Nor tel Netw ork s Se ri es 5 r oute r is not com patib le with th is f eature .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-12 312410- A Re v 00 Using th e Quick-Star t Comma nds Refe r to the c omm an ds in Ta b l e B - 1 when quick-starti ng the AN/DC or ANH-8/DC.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R e v 00 B-13 Runn ing th e Quic k-Start Scri pt After you ent er run install.bat , the AN/DC or ANH-8 /DC progre sse s through t he Quic k -Star t scr ip t as f o llows: 1. The scrip t be gins prompting you for the ini ti al Globa l W orksheet inf ormat i on.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-14 312410- A Re v 00.
312410-A R e v 00 C-1 Append ix C T ec hni cal Speci ficati ons This appendi x pro vides • AN/DC Phy sical Spe cif icatio ns • ANH-8/DC Phys ical Specif ications • Po wer Supply Specif ications .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-2 312410- A Re v 00 P o wer Sup pl y Specif i cations Specif ica tions for bot h the AN/DC AN and ANH-8/DC po wer supply: • Nominal in put v .
Technic al Spec ific ations 312410-A R e v 00 C-3 T able C-1. AN/DC Network Interfaces Network Interface D escription Ethe r net a nd Second Et hernet Suppor ts the Et her net and IEEE 802.3 st andards th at prov ide LAN conne cti vity . The Ethe rnet interf aces on an AN /DC i nc lud e a 10 Bas e-T (UTP) a nd an 802.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-4 312410- A Re v 00 ANH-8/D C Hard wa re Communications Options Ever y ANH-8/DC include s • 9 Ethe rnet LAN repe ater ports (1 A UI and 8 UTP.
Technic al Spec ific ations 312410-A R e v 00 C-5 Connect or Pinouts This sec tion lists pinouts for the AN/DC and ANH-8/DC co nnectors: • Attach ment Un it Inte rface (A UI) Por ts • 10Base-T Re peater Ports (ANH-8/DC only ) • Synchronou s Interf aces • ISDN BRI Port s • Local Cons ole Connection s T able C-2.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-6 312410- A Re v 00 Attachment Unit Interface (A UI) P or ts The AN/DC back p anel and ANH-8 /DC front panel co ntains a s tandard 802.3 A UI DB-15 re cept ac le conne ct or wi th a sl ide loc k fo r co nnec ti on t o the A UI.
Technic al Spec ific ations 312410-A R e v 00 C-7 10Base-T Repeater P or ts (ANH-8/DC only) The eight Ethernet 10Ba se-T repeate r port RJ-45 c onnectors on the ANH-8/DC front pane l pro vi de UTP s uppo rt .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-8 312410- A Re v 00 Synchr onous Interfaces The AN/DC and ANH-8 /DC support tw o synchron ous inter faces, la beled COM1 and COM2. Syste ms with a Third Sy nchronous I nterfac e or ISDN BRI upg rade module supp ort a thi rd synchr onous port .
Technic al Spec ific ations 312410-A R e v 00 C-9 T able C-5. Synchr onous P ort Pin Assi gnments Pin Assignm ent Pin No. Signal Name Pin No. Signal Name 1 FGND 23 D CD- 2 SD+ 24 ST - 3 RD+ 25 R T - 4.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-10 312410- A Re v 00 ISDN BRI P or ts The AN/DC and ANH-8/ DC support the BRI standar d for ISDN usi ng an optional ISDN/BRI modul e. Th e i nte grat ed ISDN BRI fu nct io nal it y al l o ws you to connect direct ly to the ISDN networ k, as oppos ed to connec ting via a terminal adapter .
Technic al Spec ific ations 312410-A R e v 00 C-11 The AN/DC and ANH-8 /DC shipping pac kage incl udes the Ord er No. 110310 console /modem kit fo r connect ing de vices to the Cons ole port. • T o connect a modem to the Cons ole port , use the Order No.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-12 312410- A Re v 00.
312410-A R e v 00 D-1 Append ix D Requi remen ts f or Eur opean Ope ra t io n This appe ndix pro vides inf ormation requi red for oper ating the AN/DC a nd ANH-8/DC in Europe . ANH-8/D C Safety Status T ables D-1 , D-2 , and D-3 list the safe ty statu s of inte rconnection p oints to the connecti on of other e quipment.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-2 312410- A Re v 00 AN/DC Safety Status Ta b l e D - 4 lists the saf ety stat us of inter connectio n points t o the conne ction of other e quipment. Safety Status (Third Synchr onous Interfa ce Module) Order Nos.
Require ments for Euro pean Ope ratio n 312410-A R e v 00 D-3 Synchr onou s Ca bling Requiremen ts Refe r to Figure D-1 throug h Figur e D-3 and Ta b l e D - 6 through Ta b l e D - 8 for synchron ous int erfa ce cabl in g infor m at ion . Note th e foll owing compl iance req ui reme nts: • V .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-4 312410- A Re v 00 Figure D-2 . Cable 7220 ( V .35 Com pliant) 9 D ata Carrier Detect+ 8 Data Carrier Detec t 10 Se nd Ti ming+ 15 S end Ti mi.
Require ments for Euro pean Ope ratio n 312410-A R e v 00 D-5 T able D-7. V . 35 Interf ace (Order No. 7220) Nortel Network s T ermination Rem ote T ermination Pin Signal Pin Signal 38 VSD+ P Send Dat.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-6 312410- A Re v 00 Figure D-3. Cab le 7224 (X. 21 Compliant) T able D -8. X.2 1 Interface (O r der No.
Require ments for Euro pean Ope ratio n 312410-A R e v 00 D-7 ISDN BRI Requ iremen ts The ISDN BRI modul e (Order No s. AE0004006, AE001 1013, and AE 0011019 for the ANH-8/ DC) and ISDN BRI upgrade modul e (Order Nos.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-8 312410- A Re v 00 ISDN BRI Clearances an d Creepage Dista nces The clea rances and creepage distance s (sho wn as X an d Y , respecti v ely ,.
Require ments for Euro pean Ope ratio n 312410-A R e v 00 D-9 The cree page dista nces appl y to the nor mal of f ice en vironmen t. When th e local en vironment wit hin the host chas sis is subj ect .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-10 312410- A Re v 00 ISDN BRI Connector Pinou ts Ta b l e D - 1 2 lists t he ISDN conne ctor pinouts .
312410-A R e v 00 Index- 1 Numbers 10Base-T ports (ANH-8/DC), 2-13, 2-17, C-7 A AN/DC connec t ing to the power source, 1 -18 dimensi ons, C -1 installing in an elect ronic encl osure rack, 1-6 on a fl at su rface, 1-6 on a wall, 1-9 LEDs.
Index-2 312410- A Re v 00 straigh t-thr ough, 2- 1 4, C-7 supply ing, 2- 4 sync hron ous, C -8 cagenuts, for elect ronic enclo sure rac k, 1-7 clocki ng, A-2 cold bo ot, 4-10 collision d etection AN/D.
312410-A R e v 00 Index-3 electroni c en closure ra ck installing AN/DC in, 1-6 installing ANH-8/DC in, 2-7 physical sp ecific ations, 1-4 en vironmental sp ecific ations AN/DC, 1-5 ANH-8/DC, 2-6 Ethe.
Index-4 312410- A Re v 00 Power , 4- 6 Run, 4-6 RX (Receiv e), 4-8 TX (T ransmit), 4-8 LEDs, AN/DC PO WER, 4-4 linking ANH-8/DCs, 2-14 Local Boot attachin g a co nsole, 1-12 , 2-20 definiti on, 3-2 re.
312410-A R e v 00 Index-5 R repeater ports (ANH-8/DC) 10Base- T , 2-13, 2-17, C-7 resetting, 4-10 RIP worksheet, B-5 RLSD 1 (Rece iv ed Line Sig nal Dete ction 1) LED, 4 -5 RLSD 2 (Rece iv ed Line Sig.
Index-6 312410- A Re v 00 W wall-m ounting AN/DC, 1-9 ANH-8/DC, 2-10 wa rm boot , 4-10 X X.21 conn ections, C-8.
An important point after buying a device Nortel Networks AN/DC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nortel Networks AN/DC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nortel Networks AN/DC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nortel Networks AN/DC you will learn all the available features of the product, as well as information on its operation. The information that you get Nortel Networks AN/DC will certainly help you make a decision on the purchase.
If you already are a holder of Nortel Networks AN/DC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nortel Networks AN/DC.
However, one of the most important roles played by the user manual is to help in solving problems with Nortel Networks AN/DC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nortel Networks AN/DC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
