Instruction/ maintenance manual of the product Media Dependent Adapters 302403-G Nortel
Go to page of 32
Par t No . 3024 03- G Jul y 2001 4401 Gr eat Ameri ca Parkwa y Santa Clara, CA 9 5054 *302403-G* Installing Me dia Dependen t Adapters (MDAs).
Copyright © 2001 Nortel Networks All righ ts res erve d . Ju ly 2001 . The inf ormation in t his docum ent is subject to change without not ice. The statements, configurations, t echnical data, and recommendations in t his docum ent are believed to be accurate and reliable, but are presented wit hout express or implie d warran ty .
1 Product Safety Meets requirements of: CSA 22.2 No. 95 0-M95/UL 1950, 3rd ed. EN60950: 1992 /A1:19 93 /A2:1993 /A3: 1995 /A4: 199721CFR , Chapter I EN60825-1 :1994 /A1 1:19 96 Caution: Only qu alified technic ians shou ld insta ll th is equi pme nt.
2 W ar ning: A vertisse ment: L ’é qui pement à fibre opt ique peu t é mettre des rayons laser ou infrarouges qui r isq uen t d ’ ent ra î ner d es l é sions oculaires. Ne jam ais regard er da n s le port d ’ un c on nec te ur ou d ’ un c â ble à f ibre o pti que .
3 Intr oduct ion This g uide d escribe s and pr ov ides in stallatio n instru ctio ns for Nortel Ne tworks * me dia d epend ent adapt ers (MDAs). It cont ains the follo wing to pics : • “ Su ppo r.
4 Supported i nter faces and produc ts Ta b l e 1 shows th e inte rface ty p es used wi th the M DAs desc rib ed in th is gui de. MDA descri pti ons This se ction d escribe s the fol lowin g MDAs: •.
5 • “ GBIC MDA ” on pa ge 22 10BASE-T/100BASE-T X MDAs The 1 0BASE-T/100BASE-T X MDAs use four RJ-45 (8-p in modul ar) co nnect ors , co nfigur ed as medi a de pen dent in t erface - crossover (MDI-X) connectors.
6 Figure 1 4 00 -4T X and 810 0- 4TX MDA front pan els The 10BAS E-T/100BASE -TX MDA ports ca n operat e at either 10 Mb/s or 10 0 Mb /s. T he p ort spee d is dete rmined throu gh au tone gotia tion wi th its connec ting de vice.
7 Ta b l e 2 descr i be s th e 400- 4T X and 81 00 -4TX MDA f ron t -pan el . T a b le 2 400- 4T X and 81 00 -4TX MDA fron t pan el Item Label Description 1 100 100 BA S E-T X po r t st atu s LEDs ( gr ee n ): On: The c orr espond ing por t is se t to op er ate at 100 Mb/s.
8 Fig ur e 2 shows t he fro nt pan el of t he BPS2 00 0- 4 TX MDA. Figure 2 BPS2 00 0- 4T X MD A f r on t pan el Ta b l e 3 describes the BPS2 000-4TX MDA front-panel compo nent s.
9 100BASE-FX MDAs The 100B ASE-FX MDAs c onfo rm to the IEEE 80 2. 3u 100B ASE -F X st andar d and can at t ach fib er-base d 10 0 Mb /s conne ct ions to F ast Eth ern et d evic es. Th e 100 BAS E-F X MDA s do no t su pp or t s ing le - m od e fi b er ca b le .
10 Fig ur e 3 shows t he front panel s of the 4 00- 2F X MDA and t he 8100 -2F X M DA. Figure 3 4 00 -2F X and 810 0- 2FX MDA front pan els BS45071A RX TX 100BASE-FX RX TX 100BASE-FX Activity Link F D.
11 Ta b l e 4 descr i be s th e dual -port 400- 2 FX MDA and the 81 00 - 2FX MDA fron t-pan el com ponen ts. Fig ur e 4 shows t he fro nt pan el of t he dual- por t BPS20 00-2 FX MDA. T a b le 4 400-2 FX M DA an d 81 00- 2F X M DA des cri pt ion Item Label Description 1 Li nk C ommu nic ati ons link L EDs (g reen): On: Valid com munications link.
12 Figure 4 BPS2 00 0- 2F X MD A f r on t pan el Ta b l e 5 descr ibe s the du al- por t BP S2 00 0-2F X MDA front -pa nel compo nent s. T a b le 5 BPS200 0- 2FX M D A d esc ription Item Label Description 1 Li nk Link stat us L EDs (g re en) : On (gr ee n): V alid 100 Mb/s co mm unication s link.
13 Quad-port 100B AS E-FX MDAs The qua d-p ort 100BA SE- FX M DAs u se f our lo ng wave 1300 nm MT -RJ co nn ectors t o at t ach dev ices o ver 62. 5/ 12 5 micro n mu ltimod e fiber optic cable . Fig ur e 5 shows t he front panel s of the 4 00- 4F X MDA and t he 8100 -4F X M DA.
14 Ta b l e 6 descr i be s th e 400- 4F X MDA and the 8100-4 FX M DA front-panel c omponents. Fig ur e 6 shows t he fro nt pan el of t he BPS2 00 0- 4 FX MDA. T a b le 6 40 0-4FX MDA / 8100-4FX MDA descri ption Item Label Description 1 Li nk Com muni cat ions link LEDs (g ree n): On: Valid com munications link.
15 Figure 6 BPS2 00 0- 4F X MD A f r on t pan el Ta b l e 7 describes the BPS2 000-4FX MDA front-panel compo nent s. T a b le 7 BPS200 0- 4FX M D A d esc ription Item Label Description 1 Link Link status L EDs (green) : On (gr ee n): V alid 100 Mb/s co mmunica tion s link.
16 1000 BASE-X MDAs The follow ing are the 1000BASE-FX MDAs. For a complete list of MDAs, se e T a bl e 1 o n page 4 . For insta llatio n instru c tio ns, see “ Inst alling a n MDA ” on page 24 . Shortwave Gigabit MDAs The f ol low in g 10 00 BASE -S X MDAs co nf or m to th e I E EE 802.
17 Figure 7 4 50 -1S R and 450 -1S X M D A fron t pane ls 1000BASE-SX TX RX Phy Link Activity 450-1SX MDA TX RX 1000BASE-SX RX 1000BASE-SX TX Activity Link Phy Select 450-1SR MDA 3 BS45044A 4 3 4 450-.
18 Ta b l e 9 descr i be s th e 45 0-1S R MDA an d t he 450 -1S X MDA fro nt pan el c omp on ents . T a b le 9 450-1 SR / 450- 1S X M DA des crip t ion Item Label Description 1 Li nk Com mu nicat ion lin k LEDs (gr ee n): On: Valid commun ications link.
19 Longwave Gigabit MDAs The fol low in g 10 00 BASE - LX MDAs conf o rm t o the I E EE 802. 3z 1 000BAS E- LX standa rd and use lo ng wave 130 0 nm f iber opt i c co n ne c tor s to co nn e ct dev ic es ov er si ng le mod e (5 km/3 .1 mi) o r mu ltimod e (550 m/18 05 ft ) fibe r optic cabl e.
20 Figure 8 4 50 -1LR and 450 -1 LX M DA f ro nt pan el s 1000BASE-LX TX RX Phy Link Activity 450-1LX MDA BS45045A 3 4 2 1 TX RX 1000BASE-LX RX 1000BASE-LX TX Activity Link Phy Select 450-1LR MDA 3 4 .
21 Ta b l e 1 0 de scr ibe s th e 45 0 -1LR MDA an d t he 4 50- 1L X MDA front-panel c omponents. T a b le 10 45 0-1L R a nd 4 50-1L X MDA des cript ion Item Label Description 1 Li nk Com mu nicat ion lin k LEDs (gr ee n): On: Valid commun ications link.
22 GBIC M DA The 45 0- 1GB I C MDA ( Fi g ure 9 ) h as a sing le Host port for Gigabi t Interface Conve rters (GBICs). GBICs are hot- swappa ble inp ut/outpu t enha ncemen t compo nents tha t link Gigabit Eth ernet por ts wi th fi ber o ptic ne two rks.
23 Figure 9 450- 1 GBI C MD A Fr ont Pa n el GBIC Phy Link Activity 450-1GBIC MDA BS450102A 3 4 450-1GBIC MDA 2 1 GBIC model with e xtr actor tabs GBIC model with e xtr actor handle SC connector.
24 Ta b l e 1 1 de scri be s th e 45 0-1 G BIC M D A fr ont- pa nel compo nent s. Ins t alli n g a n M DA Be for e yo u begi n i nsta lli ng a n M DA, see “ MDA des criptions ” on pa ge 4 for spe cif ic in for ma tio n ab out yo ur M DA.
25 The Upl i nk/ Exp ansio n Mo dul e slo t on supp ort e d swi tch es acc omm oda te s a si ngle MDA usin g the fol l ow in g co nn ect ors. T o install an MDA: 1 Unpl ug t he AC power co rd from the back of t he switch , or unpl ug th e swit ch mo du le fro m the swi t ch back plan e.
26 Figure 10 I nstalli ng an MDA 4 Press t he MDA firm ly into t he Uplin k/Expans ion M odule slot. Be sure that the MDA is fu lly seat ed into the mati ng conne ct or .
27 For instructions o n attaching devices to the MDA ports, refer to th e p ublication for y our switc h. After c onn ecting the port cabl es, fo l lo w th e i nstruct io ns t o co nnect po wer and veri fy the installa tion .
28 Ins t al li n g a GB IC in a n MD A Before installing a GBIC, see “ GBIC MDA ” o n pa ge 22 for spe c i fic inf orma tio n about yo ur MDA. The 45 0-1 GBI C MDA Hos t port is cov ered wi th a sp ring- lo ade d fille r pa nel t hat ro tates o ut of th e way as you pu sh the GBIC int o plac e.
29 Figure 1 1 Install ing a G B I C 3 Press on the front of th e GBIC u ntil it snaps into pla ce. 4 Remo ve the ru bb er plug to c onnec t ca bles. Removing an Instal led GBIC from an MDA F or a de scri pti on of the GB IC MDA , see “ GBIC MDA ” on page 22 .
30 Figure 12 Remo ving a GB IC wit h spring tab s • If the GBIC has an extracto r handle ( Figu re 9 on page 23 ), gra sp the handl e and pull f irm ly to remo ve th e GBIC from the MDA ’ s Host port.
An important point after buying a device Nortel Media Dependent Adapters 302403-G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nortel Media Dependent Adapters 302403-G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nortel Media Dependent Adapters 302403-G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nortel Media Dependent Adapters 302403-G you will learn all the available features of the product, as well as information on its operation. The information that you get Nortel Media Dependent Adapters 302403-G will certainly help you make a decision on the purchase.
If you already are a holder of Nortel Media Dependent Adapters 302403-G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nortel Media Dependent Adapters 302403-G.
However, one of the most important roles played by the user manual is to help in solving problems with Nortel Media Dependent Adapters 302403-G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nortel Media Dependent Adapters 302403-G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
