Instruction/ maintenance manual of the product ADP102 Nilfisk-ALTO
Go to page of 14
LT O LT O TM ADP102 ADP152 User's Manual Version 1.0 ---English---.
LTO LTO TM Care & Safety Instructions 1 All the safety and operating instructions should be read before this product is installed and operated. We recommend that installation be carried out by an authorized mobile electronics installation company .
LTO LTO TM Introduction 2 Dear Customer, Thank you for choosing this ALT O Mobile ADP Series Full-Range Class-D Power Am plifier. W e hope you will enjoy using this product as much as we enjoyed developing it. The ADP Series is the result of considerable research and development in our R&D centers in Europe and the Far East.
LTO LTO TM Drawings Showing the Front and Rear Panels 3 1 1 2 2 3 3 4 4 5 5 6 6 FREQ. HP/FLA T/LP GAIN CH 1. 2 CH 1. 2 FUSE GND 12V REM CH2 CH1 CH2 CH1 INPUT OUTPUT POWER INPUT.
Mounting the Unit 3 3 Power, Ground and Remote Switch-On T erminals LTO LTO TM Installation & Setup Instructions 4 You r ADP Serie s Power Amplifier has two fixing 'ears' at each side, allowing it to be firmly screwed to a suitable surface.
+12V The terminal marked +12V should be connected to a permanent (i.e. not ignition switched) positive 12 Volt supply from the vehicle battery. GND The terminal marked GND (Ground) should be connected to a cable which is terminated to the vehicle chassis.
4 4 Fuse 5 5 Input Gain Control Use this control to match the pre-amp output level of your car audio source unit (tape or CD player) to the input stage of the ADP amplifier . The amplifier's input gain is variable from 400mV (MAX Gain) to over 15V (MIN Gain).
See how far you can take the volume control before the signal begins to clip (you may need to reduce the amp gain if it gets too loud). If you see it clip on the scope, back off the volume control a little. Now increase the gain on the amp until you find the highest level before distortion or visible clipping.
8 LTO LTO TM Although commonly referred to as a "digital" amplifier, C lass-D is more accurately described as a Pulse Width Modulated (PWM) amplifier. A PWM amplifier converts the music (which is a complex arrangement of sine waves) into a series of pulses.
9 LTO LTO TM Further Information For additional information, please visit our website at www.alto mobile.com , which includes a technical discussion forum where users can exchange ideas.
10 T o be protected by this warranty , the buyer must be able to produce a numbered, machine printed sales receipt from his supplying dealer that clearly shows the dealer's name and address, the buyer's name and address, purchase date, model and serial number of the product.
11 LTO LTO TM ADP102 Power Output (RMS, 4 ohms): THD: Residual Noise: Xover: Input Gain Range (MAX - MIN): Operating Voltage: Output Efficiency at Full Power: Protection Circuitry: Idle Current (no signal): Standby Current, REM input low: Size: 50W X 2 <0.
12 ADP152 Power Output (RMS, 4 ohms): THD: Residual Noise: Xover: Input Gain Range (MAX - MIN): Operating Voltage: Output Efficiency at Full Power: Protection Circuitry: Idle Current (no signal): Standby Current, REM input low: Size: 75W X 2 <0.05% @10Vrms 120uVrms (A-wtd) HP/ LP/ FLAT switchable.
NF01173-1.0 No. 1, Lane 17, Sec. 2, Han Shi W. Road, T aichung, 401 Taiwan http://www.altomobile.com T el: 886-4-22313737 email: info@altomobile.com Fax: 886-4-22346757 All rights reserved to AL TO Mobile.
An important point after buying a device Nilfisk-ALTO ADP102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nilfisk-ALTO ADP102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nilfisk-ALTO ADP102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nilfisk-ALTO ADP102 you will learn all the available features of the product, as well as information on its operation. The information that you get Nilfisk-ALTO ADP102 will certainly help you make a decision on the purchase.
If you already are a holder of Nilfisk-ALTO ADP102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nilfisk-ALTO ADP102.
However, one of the most important roles played by the user manual is to help in solving problems with Nilfisk-ALTO ADP102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nilfisk-ALTO ADP102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
