Instruction/ maintenance manual of the product 3.4 PC Nilfisk-ALTO
Go to page of 22
MAXIDRIVE3.4 PC 3 W A Y STEREO DIGIT AL CROSSO VER User's Manual LTO R www .altoproaudio .com V ersion 1.5 Februar y 2006 English.
1 SAFETY RELA TED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol, wherever used, alerts you to the pre- sence of un-insulated and dangerous voltages with- in the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death.
Dear Customer: PREF ACE Thank you very much L TO AUDIO TEAM 2 For our L TO AUDIO TEAM, music and sound are more than a job...are first of all passion and let us say our obsession! We have been designing professional audio products for a long time in cooperation with some of the major brands in the world in the audio field.
T ABLE OF CONTENTS 1. INTRODUCTION ................................................................................................................................... 4 .. 2. FEA TURES ..................................................................
1. INTRODUCTION 2. FEA TURES 3.1 The Front Panel 3. CONTROL ELEMENTS 4 Single rack unit Easy to operate front panel controls 2 input connectors are compatible with balanced XLR and JACK 6 outputs are balanced XLR-M connector A/D and D/A converters for a 1 17dB dynamic range Delay lines up to 2.
5 1>. Ensure that power to the MAXIDRIVE3.4 PC and the computer is switch off. 3>. T urn on your audio system, including the MAXIDRIVE3.4 PC. Now boot up your computer and run the PC editor (see "Configuration of the system"). 2>. Connect the MAXIDRIVE3.
6 4. GETTING ST ARTED 4.1 Configuration of the System 1. 0 Meanwhile, the system will restore the exact operating conditions at the time of switching off. Click the SEL key to select proper PRESET or ID status. r user When PRESET LED lit, you can use the UP and DOWN keys to select factory PRESET s (1 ~ 10) o PRESET s (1.
7 CS 4.4 First Steps with the PC Editor T o avoid accidentally overwriting an existing PRESET , it is important that you follow the correct routine when ini- tiating a session between the MAXIDRIVE3.4 PC and your computer . 1>. With the MAXIDRIVE3.
8 4.5 Edit Mode (Password Protection) Full Edit: This is the DEF AUL T mode. No password is set at the factory . From here you can lock the unit by clicking within the empty or buttons. A text box will open, allowing you to enter a password of your own Partial Lock T otal Lock choice.
9 2 NOISE GA TE Y ou can set the MAXIDRIVE3.4 PC to cut the signal if it falls below a certain level. Most often used to cut the background noise between music tracks. 3 P ARAMETRIC EQUALIZA TION (EQ) Each of the channels (both inputs and outputs) has a fully variable 5-band parametric equalizer .
10 3 P ARAMETRIC EQUALIZA TION (EQ) 7 5-band full parametric equalization is provided on each of the Input and Output channels. The Center Frequency , Gain and Bandwidth are all variable. In addition, the MAXIDRIVE3.4 PC allows you to select from a list of different EQ contours.
11 Butterworth type with 6dB, 12dB, 18dB or 24dB per octave slope Bessel type with 12dB, 18dB or 24dB per octave slope Linkwitz-Riley type with 12dB, 24dB or 48dB per octave slope The different filter characteristics can be seen on the PC Editor's graphical display .
12 What our processor allows us to do is set our preferred upper level it's like having your own DJ poised with her hand over the volume control, ready to turn it down when the music gets uncomfortably loud.
13 Output s1~6 , RS485 OUT GROUND HOT (+) COLD ( ) 3 2 1 BALANCED XLR-F 8. APPLICA TION # 01 02 03 04 05 06 07 08 09 10 Name DEF AUL T 2X2W+MAX 2X3W 2X3W+MSB+MAX 4W+2MAX 4W+BSB+2MAX 5W+MAX 5W+BSB+MAX .
14 CH-A CH-B CLIP SIG POWER ON OFF CLIP SIG PROT CH-A CH-B CLIP SIG POWER ON OFF CLIP SIG PROT.
15.
16 CH-A.
17 CH-A CH-B CLIP SIG POWER ON OFF CLIP SIG.
18 From RS485 OUT to RS485 IN From RS485 OUT to RS485 IN t o/f r o m Rs232 (Front panel) t o/f r o m RS232 Serial Port MAXIDRIVE3.4 PC 3-W A Y STEREO DIGIT AL CROSSOVER e.
19 9. TECHNICAL SPECIFICA TIONS Peak, 6dB Lo-Shelf, 12dB Lo-Shelf, 6dB Hi-Shelf, 12dB Lo-Shelf, Notch INPUT section Connectors 2 x COMBO Nominal input sensitivity 0 dB (0.775 V) Input Impedance 30kOhm, electronically balanced Maximum Input Level +20dBu Input Gain -30 / +6 dB variable in 0.
10. W ARRANTY 1. W ARRANTY REGISTRA TION CARD T o obtain Warranty Service, the buyer should first fill out and return the enclosed W arranty Registration Card within 10 days of the Purchase Date.
NF -1.5 01738 No. 1, Lane 17, Sec. 2, Han Shi West Road, T aichung 40151, T aiwan http://www .altoproaudio.com T el: 886-4-22313737 email: alto@altoproaudio.com Fax: 886-4-22346757 c All rights reserved to AL TO. All features and content might be changed without prior notice.
An important point after buying a device Nilfisk-ALTO 3.4 PC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nilfisk-ALTO 3.4 PC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nilfisk-ALTO 3.4 PC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nilfisk-ALTO 3.4 PC you will learn all the available features of the product, as well as information on its operation. The information that you get Nilfisk-ALTO 3.4 PC will certainly help you make a decision on the purchase.
If you already are a holder of Nilfisk-ALTO 3.4 PC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nilfisk-ALTO 3.4 PC.
However, one of the most important roles played by the user manual is to help in solving problems with Nilfisk-ALTO 3.4 PC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nilfisk-ALTO 3.4 PC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
