Instruction/ maintenance manual of the product GB 1133 Nilfisk-Advance America
Go to page of 20
Instruction manual GB 1133 Categories of application: U, S, C, B1, EOB, K1 ATTENTION Keep these instructions for future reference!.
1 Contents Paragraph Page 1 Contents 2 2 Scope of the instruction manual 3 3 Tests 4 4 Categories of application 5 5 Technical specifications 6 6 General notice on safety 7 7 Filter and emptying syste.
2 Scope of the instruction manual This instruction manual is valid for the the following machine types: GB 1133 – U(L) GB 1133 – C(M,H) GB 1133 – S(M) - B1 GB 1133 – C(M,H) - B1 GB 1133 – C(.
3 Tests All Nilfisk-Advance systems are tested in or der to comply with the requirements of system safety regulations. They have fulfilled the technical safety demands according to the following speci.
4 Categories of application This Nilfisk machine is suitable for remo ving dusts of the following categories of application: “U“ suitable for removing hazardous, dry, not inflammable dusts whose MAK * limiting value is greater than 1 mg/cm³ (comparable to the new dust class “L“ - light hazard - defined by EN 60335-2-69).
5 Technical specifications Voltage 400 V Rated power 13,000 W Vacuum 320 mbar Connection Ø 70/100 mm Airflow 750/930 m³/h Filter area Main filter (U,S,C) 52,000 cm² Prefilter (K1) 52,000 cm² Main .
6 General notice on safety Only original Nilfisk spare parts may be used. The machine may only be operated by instructed and authorised individuals. Liquids, aggressive gases, flammable materi als or smouldering particles should not be removed. The machine may only be used for cleaning dry surfaces and is not suitable for outdoor use.
7 Filters and emptying sy stems The installed main and exhaust filter s are approved by the German Trade Association Institute for Safety at the Work place (BIA). The transmission factors are lower than the limiting values r equired by relating regulations.
8 Initial operation Please read these notes of safety before initial operating. The application scope of the machine is marked on the rating-plate. Industrial vacuum cleaners are exclusively designed for removing settled dusts. Extractors are designed for removing dust at that very place where it is produced.
9 Adjusting the automatic gear change of the minimum airflow Use the performance profile to adjust the cutoff point for the minimum airflow of extractors. First of all, find out the minimal airflow that ensures a good operation of the dust-producing system.
The works for configuring an extractor (connecting the cable, adjusting the cutoff point) may only be carried out by a technician or skilled personnel using suitable tools. When using the vacuum cleaner outdoors, use only a type H07RN-F cable. Connecting the cable must be carried out according to the manual added to the machine.
GB 1133 Performance profile.
10 Monitoring the airflow All Nilfisk vacuum cleaners - except category of application “U“ - are fitted with a manometer that allows you to monitor the minimum airflow in order to guarantee an optimal air speed within the suction hose.
11 Cleaning the filter Nilfisk-Advance systems are fitted with a devic e for cleaning the main filter. First of all, switch the machine off. Then move the shaker handle placed at the container vigorously with a push-pull movement.
12 Emptying the container Industrial vacuum cleaners with antistatic design need to be emptied after every single use. First of all, switch the motor off. Wait a moment until the dust has settled down before you separate the dust collecting container from the upper part of the machine: Lower the container by using the lifting mechanism.
13 Disposal of collected dust Category of application: “U“ The are no particular prescriptions, but take care that no one around you will be affected by the dust. The disposal of the collected dust has to be carried out according to local prescriptions.
Category of application: “C“ and “K1“ Type B: Disposable container Art.no. 031 101 When the container has been torn away from the machine, close it by the lid and fix the lid by the clamp ring.
14 Pre-separator The system can connect to secondary interceptor tanks for even greater waste capacity of 200 litres at a time. The lid fitting both sizes of pre-separators (125 and 200 litres) and the hose connection have to be ordered separately. The separator trolley runs on three wheels.
15 Notice on K1 vacuum cleaners used for removing asbestos A vacuum cleaner that has been used for re moving asbestos in a contaminated area may no longer be used in a non-contaminated area.
16 Service Nilfisk-Advance Limited Newmarket Road Bury St. Edmunds Suffolk IP33 3SR Tel: 01284 763163 Fax: 01284 750562 Internet: www.nilfisk-advance.com ______________________________________________.
An important point after buying a device Nilfisk-Advance America GB 1133 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nilfisk-Advance America GB 1133 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nilfisk-Advance America GB 1133 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nilfisk-Advance America GB 1133 you will learn all the available features of the product, as well as information on its operation. The information that you get Nilfisk-Advance America GB 1133 will certainly help you make a decision on the purchase.
If you already are a holder of Nilfisk-Advance America GB 1133, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nilfisk-Advance America GB 1133.
However, one of the most important roles played by the user manual is to help in solving problems with Nilfisk-Advance America GB 1133. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nilfisk-Advance America GB 1133 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
