Instruction/ maintenance manual of the product PR5 Niles Audio
Go to page of 28
B LENDING H IGH F IDELITY AND A R CHITE CTURE ® INST ALLA TION & OPERA TION GUIDE ® MODEL S I N F R A R E D S E N S O R K N O C K O U T I N F R A R E D S E N S O R K N O C K O U T.
Congr at ulations! Thank you for choosing a Performance In-Wall Loudspeaker from Niles. With proper installation and operation, you'll enjoy years of trouble-free use. Niles manufactures the industry's most complete line of custom installation com- ponents and accessories for audio/video systems.
Limit ed W arr anty Niles Audio Corporation ("NILES") warrants its loudspeaker products to the original purchaser to be free of manufacturing defects in material and workmanship for a period of five years from date of purchase. This Warranty is subject to the following additional conditions and limitations.
DETACH HERE AND RETURN TO: Niles Audio Corporation Warranty Registration Dept. P .O. Box 160818 Miami, Florida 33 1 16-0818 Model Purchased __________________ ____________ _____ ________________ _____.
Fea t ur es and Benefits Talc-Filled Polypropylene Woofer with Butyl Rubber Surround and Custom Debris Screens The Niles PR Performance series loud- speakers employ a high performance woofer made of vacuum formed polypropylene with talc added for stiffen- ing.
No-Strip Speaker Terminal Niles patented No-Strip terminal enables speakers to be connected without strip- ping the speaker wire. No-Strip terminals eliminate fumbling with wire strippers and input terminals.
PLEASE FILL OUT THE W ARRANTY REGISTRA TION CARD ON THE REVERSE SIDE, DET ACH, AND MAIL T O: Niles Audio Corporation W arranty Registration Dept. P .O.
23 Specifications.
Inst allation C onsider ations Recommended A mplifier Power For satisfactory performance, we recom- mend an amplifier with a power rating of ten to one hundred watts for the PR5; and ten to one hundred twenty-five watts for the PR6. Curiously, most speakers are not damaged by large amplifiers but by small amplifiers.
er, so you must connect the wire from the amplifier to the volume control and then from the volume control to the speaker. Speaker Wire Use 2-conductor speaker wire when con- necting PR speakers to your receiver or amplifier . For most applications, we rec- ommend you use 1 6 or 1 8 gauge stranded wire.
22 Specifications Specifications Model PR6 Driver Compliment 6-1/2 ” Talc-Filled Polypropylene Woofer with Custom Debris Screen and Butyl Rubber Surround 3/4 ” Kaladex ® Tweeter Housed in a Low D.
21 Specifications Specifications Model PR5 Driver Compliment 5-1/4 ” Talc-Filled Polypropylene Woofer with Custom Debris Screen and Butyl Rubber Surround 3/4 ” Kaladex ® Tweeter Housed in a Low D.
6 Speaker Placemen t Placement for Critical Listening If you like to imagine that the band or orchestra is playing in front of you as you listen to music, or you are very conscious of clarity, detail and the textures of the individ- ual instruments, you are a critical listener.
The Boundary Effect Corners can affect the bass response of the speaker powerfully! This is called the boundary effect. Y ou will emphasize par- ticular bass frequencies and cancel out other bass frequencies when you place speakers close to the wall/ceiling bound- ary or a corner wall boundary .
20 Oper ation Remo v al of Speaker and Grille Removing The Speaker If the grille is already installed, remove it by using a bent paper clip or the tip of a corkscrew and pulling it away from the frame. Utilizing two small screwdrivers or two needle nose pliers, release the snaps that hold the speaker to the frame.
19 Installa tion of the Speaker and Grille in Ne w or Existing Construc tion Adjusting the Tweeter The tweeter is housed in a precision adjust- ment mechanism which enables precise aiming of the directional high frequencies to provide optimum performance.
soundtrack to envelope you in the envi- ronment on screen. They will place back- ground music, rain sounds, traffic noise, etc. on the “ surround ” soundtrack.
Inst allation Fundamen t als Running the Speaker Wire in New Construction If you have doubts about whether you are capable of installing a Niles PR loudspeak- er in your walls, consult a Niles dealer or professional installer. They have special tools, techniques, and experience to make the impossible possible.
Speaker Phase Speaker wire has two conductors. One conductor is attached to the negative (-) terminals and one conductor is attached to the positive (+) terminals of both your speaker and your amplifier. Usually , the wire is marked for your convenience.
Installing the Speaker If the grille is already installed, remove it by using a bent paper clip or the tip of a corkscrew and pulling it away from the frame (See Figure 13) . 1 . Separate the speaker wire so that at least two inches of each conductor are free.
Try to line the holes up perfectly, because it makes pulling the wire much easier. A good technique is to snap a chalk line across the face of the studs or against the bottom of the ceiling joists. Then work backward so that you can always see the holes you have already drilled.
Identify where all of your electrical, phone, and TV wiring is likely to be and plan to route around it all. You can acci- dentally induce 60 Hz hum on your speakers if you run your speaker wire right beside electrical wire for more than a few feet. T ry to keep speaker wire running par- allel to power cables at least 3 feet away.
the drywall section can be replaced clean- ly if there is an unseen obstruction behind the wall. BE VERY CAREFUL NOT TO SAW THROUGH EXISTING WIRES, PIPES, OR STRUCTURE.
Inst allation o f Br acket s, Fr ames and Grilles in Existing W alls IMPORTANT: Before you cut into any wall, review the sections on running wire and speaker placement.
building codes, some municipalities require conduit). In traditional wood stud / drywall construc- tion you can cut the hole for the speaker and utilize the large hole to auger holes across, up or down the wall for as far as your drill bit will take you.
Inst allation o f Br acket s, Fr ames and Grilles in Ne w Constr uction Stage One: Before Drywall is Hung. Insulating the Wall Cavity. If feasible, fill the wall cavity with insula- tion at this point . Attach the wings to the bracket by snap- ping them into the sides of the bracket.
the grille with paint. The grille is construct- ed of aluminum with a perfectly even powder coat overall. This powder coat is an ideal primer. Remove the grilles before painting. If you are using spray paint, use two thin coats without any primer . If you are using a compressor and a spray gun, use the finest, most diffuse setting.
Niles Audio Corporation 1 233 1 S. W . 1 30 Street Miami, Florida 33 1 86 T el: (305) 238-43 73 Fax: (305) 238-0 1 85 www.nilesaudio.com © 2000 Niles Audio Corporation.
An important point after buying a device Niles Audio PR5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Niles Audio PR5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Niles Audio PR5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Niles Audio PR5 you will learn all the available features of the product, as well as information on its operation. The information that you get Niles Audio PR5 will certainly help you make a decision on the purchase.
If you already are a holder of Niles Audio PR5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Niles Audio PR5.
However, one of the most important roles played by the user manual is to help in solving problems with Niles Audio PR5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Niles Audio PR5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center