Instruction/ maintenance manual of the product CM8SW Niles Audio
Go to page of 24
B LENDING H IGH F IDELITY AND A R CHITE CTURE ® INST ALLA TION & OPERA TION GUIDE ® INST ALLA TION & OPERA TION GUIDE SUBWOOFER CM 8 S W.
Congratulations! Thank you for choosing a Niles ceiling mount loudspeaker. With proper installation and operation, you'll enjoy years of trouble-free use. The CM8SW is a ceiling mount subwoofer uniquely designed to provide unobtrusive low frequency augmentation.
Fea t ur es and Benefits TCC Speaker Cone The Niles CM8SW is a high-performance passive subwoofer that compliments the entire Niles ceiling mount loudspeaker line.
Infinite Baffle Design The CM8SW is designed for optimum low frequency reproduction in traditional ceil- ing environments and varying air volumes. It does not require a special enclosure to provide high performance.
Ho w Man y Sub w oo f er s? 4 Ho w Man y Sub w oof er s? For most applications a single CM8SW is appropriate. However, in large rooms, high performance listening rooms or in home theaters, an array of two or more CM8SW will deliver astounding results.
Connections Single Stereo Subwoofer A four conductor (Left+, Left-, Right+ and Right- ) wire 16 gauge or larger (see side- bar on speaker wire gauge) is run from the amplifier location to the local volume control (See Figure 4) . From the local volume control the four conductor cable is run to the CM8SW and connected to the Input connectors.
6 Connections the left and right speakers simultaneously. Additionally, the crossovers are now con- nected so that the crossover switches can be adjusted to your requirements. You must adjust the crossovers on each speaker with this hook-up. Optionally, a jumper of wire may be connected between the L+ and the R+; and between the L- and the R-.
Impedance With One or Two Subwoofers When one or two CM8SW subwoofers are connected to the satellite speakers, the overall system impedance to the amplifier lowers. System Impedance in Ohms ( Ω ) One or Two Subwoofers 8 Ω Sats 4 Ω Sats 1 Sub 4 Ω 2.
Using Speaker Selectors With Standard Volume Controls In multi-room systems with standard vol- ume controls any Niles speaker selector will maintain a four ohm load if you leave one set of room outputs unused for every speaker system with an impedance of less than four ohms (such as a CM8SW con- nected to a pair of four ohm satellite speakers).
T r eat ment & Placemen t Typically, sheetrock encloses the sub- woofer in most installations. Sheetrock has a fairly loud resonant “twang” compared to the rigid non-resonant enclosures of most floor standing subwoofers.
Inst allation F undament als Introduction If you have doubts about whether you are capable of installing a ceiling mount speak- er, consult a Niles dealer or professional installer. They have special tools, tech- niques, and experience to make the impos- sible possible.
1 1 Ins t allation F undamen t als bottom of the ceiling joists. Then work backward so that you can always see the holes you have already drilled. Paying care- ful attention to this will save you a lot of time later on! Pulling the Cable Pull the cable in sections (from the stereo to the volume control, from the volume con- trol to the speaker).
switch or receptacle, and shining a penlight into the wall. If you have access to an attic or base- ment space you can quickly see which part of the wall space is free of obstructions (See Figure 12) .
In traditional wood ceiling joist/ drywall construction you should first cut the hole for the speaker and utilize the large hole to auger holes across the ceiling (through the ceiling joists) for as far as your drill bit will take you.
Inst allation in Ne w Construc tion Stage One: Before Drywall is Hung Insulating the Wall Cavity. If feasible, fill the wall cavity with insulation at this point . Mounting The CM8 Series New Construction Bracket The hole saving bracket enables a faster and cleaner final installation of the speaker.
Inst allation in Existing Constr uction IMPORTANT: Before you cut into any wall, review the sections on running wire and speaker placement. 1. When determining the location of the speaker cutout keep in mind that the mounting dogs will extend 3/4” beyond the cutout.
Final Ins t allation in Ne w or Existing Constr uction 1. If it is possible to lay a batt of insulation into the ceiling cavity, do so. Remember to use equal amounts of insulation for each speaker. 2. Separate the speaker wire so that at least two inches of each conductor are free.
Painting the Speakers All models may be painted. The plastic will readily accept most paints. The speakers must be masked prior to painting them. The inside circular portion of the hole template can be used as a paint mask. Remove the outside portion of the template by gently pulling along the perforation.
Oper ation Congratulations A concealed CM8SW subwoofer installation frees you to use your tone controls, play the sys - tem loudly and enjoy deep extended bass, even if your satellite speakers are small. When used with satellite speakers that have substantial bass of their own, the CM8SW tightens the deep tones and augments the bass musically.
Specifications CM8SW Driver Complement 8” dual voice-coil injection molded TCC (Talc, carbon and ceramic-filled) woofer with butyl rubber surround Design Principle Infinite baffle for large and vary.
DETACH HERE AND RETURN TO: Niles Audio Corporation, Inc. Warranty Registration Dept. P .O. Box 160818 Miami, Florida 3 3 1 16 - 0818 M o d e l P u r c h a s e d __________________ ____________ _ ____ .
PLEASE FILL OUT THE W ARRANTY REGISTRA TION C ARD ON THE REVERSE SIDE, DET A CH, AND MAIL T O: Niles Audio Corpor ation W arr anty Registr ation Dept. P .
Limit ed Warr anty Niles Audio Corporation ("NILES") warrants its loudspeaker products to the original purchaser to be free of manufacturing defects in material and workmanship for a period of five years from date of purchase. This Warranty is subject to the following additional conditions and limitations.
© 2004 Niles Audio Corporation. All Rights Reserved. Niles, the Niles logo, and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. MicroPerf is a trademark of Niles Audio Corporation. All other trademarks are the property of their respective owners.
An important point after buying a device Niles Audio CM8SW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Niles Audio CM8SW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Niles Audio CM8SW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Niles Audio CM8SW you will learn all the available features of the product, as well as information on its operation. The information that you get Niles Audio CM8SW will certainly help you make a decision on the purchase.
If you already are a holder of Niles Audio CM8SW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Niles Audio CM8SW.
However, one of the most important roles played by the user manual is to help in solving problems with Niles Audio CM8SW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Niles Audio CM8SW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
