Instruction/ maintenance manual of the product AC12000E NewAir
Go to page of 15
PLEASE READ AND SAVE THESE INSTRUCTIONS NewAir AC ‐ 12000E, AC ‐ 12000H Portable Air Conditioner Owner’s Manual k0045.
BEFORE USE GENERAL SAFETY INSTRUCTIONS: • AL W A YS OPERA TE THE UNIT IN AN UPRIGHT POSITION AND PLACE IT ON A FLA T , LEVEL SURF ACE A T LEAST 14 INCHES A W A Y FROM ANY OTHER OBJECTS (Fig 1 & 4). • DO NOT PLACE OBJECTS ON THE UNIT , AND DO NOT COVER OR OBSTRUCT THE INLET OR OUTLET GRILLS (FIG.
PARTS LIST Front: Back: 1. Control panel 2. Louvers 3. Carrying handle 4. Casters 5. Air filter 6. Air inlet 7. Cord storage 8. Exhaust air outlet 9. Rubber plug / drainage point Accessories: 10. Exhaust hose 11. Hose adaptor (goes over the hose and into the window kit) 12.
INSTALLATION INSTRUCTIONS Installing the Exhaust Hose and Window Kit: FIG.5 Wall or Window Window Kit Adapter 1. Open the window and insert the window kit into the open gap. 2. Close the window until the window kit is held securely. This technique may also be used for sash windows.
Positioning the Exhaust Hose: • Insert the exhaust hose into the back of the unit and tighten it into place. • Avoid kinks and bends in the exhaust hose.
Installing the Activated Carbon Filter: 1. Remove the filter frame from the unit. 2. Separate the filter from the filter frame. 3. Remove the activated carbon filter from its plastic bag. 4. Insert the activated carbon filter into the filter frame. 5.
OPERATING INSTRUCTIONS Control Panel 1. Fan speed (ventilation) button 2. Timer button 3. Display window 4. Remote control receiver 5. Heater indicator (for AC-12000H only ) 6. Mode selection button 7. Automatic mode indicator 8. Cooling mode indicator 9.
Setting the Mode/Function: 1. Press the MODE button to select the desired mode (cooling, fan or heating). Heating mode is only available on the AC-12000H. 2. The selected mode’s indicator light will turn on. Setting the Temperature: 1. Press the “Up” or “Down” butt on to change the set temperature.
Heating Mode: When the air conditioner is in heating mode, ambient warm ai r is recycled and used to heat your immediate area. The exhaust pipe will stil l need to be fitted onto the unit in order for the cold air to be removed . When in heating mode, the machine can be set on HIGH or LOW speed.
DRAINING THE UNIT During the cooling process, some water will be extracted from the air and stored within the unit’s water reservoir. If the water reservoir is full, both the compressor and motor will stop and t he unit will beep (press any button to stop the beeping sound).
For Continuous Drainage: • Remove the rubber plug from the drainage port and retain it for future use. • Connect the drain tube to the drainage port as shown (fig. 17). • Connect the other end of the hose to a drain. FIG.16 • The drain tube may be extended by adding an extension tube with a suitable connector.
For Heating Mode: While using the heating function, please note the following: 1. In order to properly exhaust cool air, make sure the exhaust hose and window kit are properly installed (refer to page 6 for instructions). 2. Set up the air conditioner for continuous drai nage using the drain tube (refer to page 13 for instructions).
MAINTENANCE INSTRUCTIONS Always unplug the air conditioner from the power supply before cleaning. To maximize the efficiency of the air conditioner, regularly clean the unit.
TROUBLESHOOTING The air conditioner does not work. y Is the air conditioner plugged in? y Is the power outlet functioning correctly? y Is the full water tank indicator light flashing? y Is the ambient room te mperature lower than the set temperature? The unit does not produce adequate cooling.
TECHNICAL SPECIFICATIONS Model Number: AC-12000E AC-12000H Power Consumption for Cooling* 1166W / 11A 1166W/11A Power Consumption for Heating * N/A 1054W/10.
An important point after buying a device NewAir AC12000E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NewAir AC12000E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NewAir AC12000E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NewAir AC12000E you will learn all the available features of the product, as well as information on its operation. The information that you get NewAir AC12000E will certainly help you make a decision on the purchase.
If you already are a holder of NewAir AC12000E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NewAir AC12000E.
However, one of the most important roles played by the user manual is to help in solving problems with NewAir AC12000E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NewAir AC12000E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
