Instruction/ maintenance manual of the product Series 180 Neumann.Berlin
Go to page of 9
neumann. berlin the microphone comp any georg neumann gmbh · ollenhauerstr. 98 · 13403 berlin · germany fon +49 (0)30 / 41 77 24-0 · fax -50 · headoffice@neumann.
2 3 Series 180 Table of Contents 1 . Summarized Description 2. Power Supply and Cables 2 .1 Phantom Powering 2.2 Ac Supply Operation 2. 3 Battery Operation 2 .4 Operation with Unbalanced or Center Tap Grounded Inputs 2 .5 Cables 3 . Technical Specifications 4 .
4 5 Series 180 In the microphones pin 2 is the “hot phase“, in ac- cordance with the standard, and pin 3 of the out- put of the power supply must be connected to earth (see Fig.
6 7 Series 180 2 . 5 Microphone Cables The electroacoustic properties of the microphones are not affected even by very long (Neumann) ca- bles. However, if cables are well over 300 m, a fall-off in the upper frequency range becomes ap- parent. Neumann offers a wide range of cables.
8 9 Series 180 4. Frequenzgänge und Polardiagramme Frequency Responses and Polar Patterns KM 185 KM 183 gemessen im freien Schallfeld nach IEC 60268-4 measured in free-field conditions (IEC 60268-4) .
10 11 Series 180 5. Einige Hinweise zur Pflege von Mikrophonen Staubschutz verwenden: Mikrophone, die nicht im Einsatz sind, sollte man nicht auf dem Stativ ein- stauben lassen.
12 13 Series 180 M F 3 ................... bl k ............. Cat. No. 07321 The MF 3 is a table stand with iron base, 1.6 kg in weight, 110 mm in diameter. It has a black matte finish. The bottom is fitted with a non-slip rubber disk. The stand comes with a reversible stud and an adapter for 1/2" and 3/8" threads.
14 15 Series 180 nances and do not influence the directional pat- tern. Only in the upper frequency range is the out- put level slightly attenuated. The wind noise attenuation was measured with- out electrical filtering in a turbulent air stream traveling at 20 km/h, generated by a noiseless wind machine.
Irrtümer und technische Änderungen vorbehalten • Errors excepted, subject to changes Printed in Germany • Publ. 09/05 076833/A06 MF 3 MF 5 MF 4 MNV 21 m t STV... EA 2124 A mt SMK 8 i WNS 100 WS 1 00 PS 15 WNS 110 Konformitätserklärung Die Georg Neumann GmbH erklärt, dass dieses Gerät die anwendbaren CE-Normen und -Vorschriften erfüllt.
An important point after buying a device Neumann.Berlin Series 180 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Neumann.Berlin Series 180 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Neumann.Berlin Series 180 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Neumann.Berlin Series 180 you will learn all the available features of the product, as well as information on its operation. The information that you get Neumann.Berlin Series 180 will certainly help you make a decision on the purchase.
If you already are a holder of Neumann.Berlin Series 180, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Neumann.Berlin Series 180.
However, one of the most important roles played by the user manual is to help in solving problems with Neumann.Berlin Series 180. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Neumann.Berlin Series 180 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
